Jump to content
AT&T to end email-to-text ×

CoLong

Members
 View Profile  See their activity

  • Posts

    46

  • Joined

  • Last visited

 Content Type 

Everything posted by CoLong

  1. CoLong
    Thanks @bpwwer. Version 2.0.7 became available on the store this morning. A restart updated my Node Server, but after 1 sec of uptime, it disconnects. I did a reinstall, and the same thing is happening - it disconnects after 1 sec of uptime, and stays disconnected even if I restart again.
  2. CoLong
    @bpwwer: This morning we had 0.03" of precip. It uploaded to CWOP at 08:59 (see attached) and to PWS at 09:04 (see attached), but it is not showing up at all on the IoP AERISWeather page, even an hour later (see attached) - my short polls are at 300, and long polls at 3600. I will send you the debug log via email. Your help is very much appreciated. PS: I notice that the pressure reading is not updating either (see the lower panel in Clip-1 attached as compared to the value showing in the IoP table)
  3. CoLong
    @bpwwerDid you receive the debug log I sent via email?
  4. CoLong
    I'll send it to you privately. Thanks.
  5. CoLong
    Here's what the AERISWeather Error Log Shows (see attached).
  6. CoLong
    It rained today, and the current amount of precip was displayed on PWS just fine. However, the "AERIS Weather" table in IoP on my Polisy remained at zero, even though the other parameters were showing updated values during the storm. The attachments show the PWS display and AERIS Weather Table just after an update. You can see that Precip is at zero in the table, even through PWS shows 0.57 inches, and the other parameters are updated. Any help would be greatly appreciated. @bpwwer
  7. CoLong
    The UD website says the following about Polisy Pro: "Native support for 3G/4G modems gives you the ability to go off the grid. Literally! And, if you are one of those maximum-connectivity types, this model – Polisy PRO – comes standard with Dual Band WiFi and Bluetooth (4.0)!" I think I understand that the WiFi capability can be used to connect the Polisy Pro to my home network instead of a hard wired ethernet connection, but can someone please point me to where I can better understand what the 3G/4G and Bluetooth capabilities in Polisy Pro would be used for? Some example use cases would be very helpful.
  8. CoLong
    Excellent...that will be very helpful. Should I do a PG3 reinstall/update now, or will that be included in a future release.
  9. CoLong
    I've also updated my router with the same fixed address for my Polisy, rather than leaving it on DHCP.
  10. CoLong
    I noticed that the URL showing in the ISY finder was different than what was showinh in the PG3 Current ISY edit, so I changed the latter to match the former and now the AERISWeather parameters are populating the tables in IoP correctly - problem solved. Many thanks for your help @bpwwer
  11. CoLong
    No joy...I even reinstalled the AerisWeather Node...getting a constant string of errors now (see attached).
  12. CoLong
    I could use some help with that...here's the PG3 log. Thanks. EDIT: Removed file
  13. CoLong
    I did a refresh of the Node Server page in PG3, and now the log has more entries. I've attached it below.
  14. CoLong
    As near as I can recall, this problem started right after I installed a Zooz USB 700 Series Z-Wave Plus S2 Stick in one of the USB ports, and completed the setup in the Config/System tab.
  15. CoLong
    I've done that (clicked restart on the Node Server with the Log set to Debug) and there's no change in what the log is showing in Debug, compared to Info.
  16. CoLong
    After getting everything working right on my new Polisy, the AERISWeather parameters have suddenly stopped populating the Weather and Forecast tables in IoP - all values are all blank. I've restarted Polisy, and reinstalled the AerisWeather Node Server on PG3, and its been showing Status "Connected" for more than an hour with no joy. I've checked and my weather station is uploading parameters to PWS correctly. The aerisweather account shows that it is being polled. The Node Server Log is shown below. Any help would be greatly appreciated. @bpwwer
  17. CoLong
    Many thanks.
  18. CoLong
    I'm in the process of migrating from ISY 944i to IoP. All the Aeris Weather node server parameters are displaying just fine on the IoP AERIS Weather and Forecast displays, as you can see from the attachments. But when I use Node Substitution Variables to populate an email report, Current Conditions node GV6, and Forecast nodes GV18, GV20, GV6 display as blanks in the report, no matter what their values in the IoP display. Others such as Current Conditions GV12 and GV13, and Forecast GV0, GV1, GV7 and several others display correct values in the report just fine. @bpwwer My Polisy characteristics are shown in the attached.
  19. CoLong
    When will the Polisy Pro be back in stock and available for purchase?
×
×
  • Create New...