raptor

I have 2-2443 access points

I can see to find were to upgrade the firmware. I've done it before but can't remember how

Also have a 2443. Should that one work because I tried putting beside it but nothing. I'm running the 99i so I guess I'm out of luck with the door sensor.

I factory reset the motion sensor, put it in pairing mode and put it a few inches from the PLM (2412s) . Try to re add it Wed 12/24/2014 05:10:26 PM : [31 B1 8F ] Added to list of devices to link to ISY Wed 12/24/2014 05:10:26 PM : [iNST-TX-I1 ] 02 62 31 B1 8F 0F 0D 00 Wed 12/24/2014 05:10:26 PM : [iNST-ACK ] 02 62 31.B1.8F 0F 0D 00 06 (00) Wed 12/24/2014 05:10:35 PM : [iNST-TX-I1 ] 02 62 31 B1 8F 0F 0D 00 Wed 12/24/2014 05:10:35 PM : [iNST-ACK ] 02 62 31.B1.8F 0F 0D 00 06 (00) Wed 12/24/2014 05:10:44 PM : [iNST-TX-I1 ] 02 62 31 B1 8F 0F 0D 00 Wed 12/24/2014 05:10:44 PM : [iNST-ACK ] 02 62 31.B1.8F 0F 0D 00 06 (00) Wed 12/24/2014 05:10:48 PM : [31 B1 8F 0 ] Failed to add device Wed 12/24/2014 05:12:09 PM : [iNST-TX-I1 ] 02 62 1D B1 E6 0F 11 FF Wed 12/24/2014 05:12:09 PM : [iNST-ACK ] 02 62 1D.B1.E6 0F 11 FF 06 LTONRR (FF) Wed 12/24/2014 05:12:09 PM : [iNST-SRX ] 02 50 1D.B1.E6 0F.42.41 27 11 FF LTONRR (FF) Wed 12/24/2014 05:12:09 PM : [std-Direct Ack] 1D.B1.E6-->ISY/PLM Group=0, Max Hops=3, Hops Left=1

I'm trying to add 2 new sensors to my ISY but keep getting errors. When adding 2842 motion sensor I got cannot determined insteon engine at first but now getting cannot determine devices type. And when adding Insteon hidden door switch I get cannot determine Insteon devices type. I make sure they are in pairing mode and place them inches from the ISY

Do you mean add it to the exception list? I removed it from the list and added it again but still get the same error message.

Windows and yes it's a static IP. With the same IP set for the exception I can get to the web interface just can't get open the admin consol

I have the same problem. I updated Java and added my IP to the exception list but still get application blocked for security

Thanks LeeG it works.

I have a Dakota Alert DCR-2500 Wireless Receiver and DCMT-2500. How do I wire the transmiter to a I/O Linc 2450. I want to prgram some scenes in the ISY trigered by motion. On the transmiter their are 3 plugs for each channels. The 3 plugs are NO, COM and NC. Were do I connect these on the I/O Link. And in the ISY the I/O link currently shows status of on or off. Will this work for what I want to do or do I have to configure something diffrently.

Thanks for the reply but could you expand on your answer. As a newbie what do i need to get this to work

Yes I do have a ISY 99.Just wasn't aware that one device could be configured as a controller in one scene and responder in another scene.

Currently I have no Zwave products except the deadbolts. So there no way to integrate with ISY

I have 3 Kwikset ZWave Motorized Deadbolt installed in my house. Only after installing them I actually realized that these had the potential to be controlled remotely. For this I believe I need some kind of wireless card to plug in the deadbolt. What exactly do I need and will I be able to control it try my ISY and Insteon switches.

I wasn't aware that the same button could be configured as controller in one seen and responder in another. I'll try that tonight and if it works it's going to be a lot of programing considering I have 4 keypad with eight buttons each but an easy fix. Thank You

I have four keypads. Lets call the keypad A-B-C-D. Lets say i turn on scene A on keypad A it also turns on the light inside button A on keypad A. If i go to any keypad A-B-C or D and push the all of button it will turn off all the lights in the house but the light that that's inside button A on keypad A stays on. This creates to problems. 1 once all the lights are off I still have keypad buttons that are glowing. 2 the next morning when I go to turn on a scene that's off but the keypad button is still on I have to push the button twice. Once turns of the button itself and does noting to the lights and the second time it turns on the button and the scene. Hope this clears it up for you.

I have 4 keypads in the house and anytime I push all of on any off them it turns all the lights off but if any keypad buttons are one(the light behind the button) it doesn't turn it off. I tried adding those keypad button to the all of scene but to do that I need to change the keypad from a controller to a responder. If I do this the keypad will no longer work as a controller right? Any way to fix this issue.