zeenon

Is there a way to have a single 6 button keylinc button blink? I'm getting weird results, the first time I ran it, it turned the Keylinc SW to on, the second (and on) it blinks ALL the keylinc buttons that are on (so A,C, OFF). 'D' is not assigned to anything. Main Prog If Status 'Security / TriggerLinc-Opened' is not Off Then Run Program 'Blink' (Then Path) Else Stop program 'Blink' Set 'Kitchen KeyLinc - D' 50% (Backlight Level) Blink If - No Conditions - (To add one, press 'Schedule' or 'Condition') Then Set 'Kitchen KeyLinc - D' 100% (Backlight Level) Wait 5 seconds Run Program 'Blink' (Else Path) Else Set 'Kitchen KeyLinc - D' 0% (Backlight Level) Wait 5 seconds Run Program 'Blink' (Then Path)

Xathros that is HOT!!!!! This forum never ceases to amaze me. Is there a way to pull the current temp from the venstar? How do you set a counter for the "Auto Off Count"? Z

Folks, I've searched the forms but have not seen either so I'm wondering if folks can post some of their programs. I have a Venstar 7 day tstat that I'm only using for HEAT that I would like to have an ISY99i control. As it is straight forward to program an off during working hours and an on when home, I would like to see other users programs that possibly have it all in one program. Second, I just have a notification email sent once a day, similar to a heart beat. I would like to jazz it up a little with HTML. Any HTML examples? On another note, is there a way to have a program setup informing you that the power is back on? This heart beat was a god sent during the recent power outages during hurricane Sandy since we were without power for an extended period. All of a sudden at 10:30PM I get the daily 11AM notification email. I'm sure this is not the proper way to program this. Z

Fixed with the above directions. Z

Yes Insteon_UD99 v.3.2.6 (2012-05-04) on both the firmware and UI Z

I consider my home install pretty lucky because I really have not had any issues. I buy a new switch, start up the admin console add it and move on. I recently tackled a 4 way switch install which went well (1 Keylinc and 2 Switchlincs) Button A is controlled by either a remote linc button or the Keylinc A. Now because I have the keylinc I wanted to program the other buttons B, C, D along with the remotelinc buttons. So to make a long story short I'm really stuck. I deleted the switchlinc and no matter what I do, I can not add it back. If I try to backup the ISY, I get an error CONF/XXXXXX.REC where XXXXXX is the address of the switch. Any help would greatly be appreciated. I just want a scene like I currently have with Keylinc button A, in which a remotelinc or keylinc turns on a switch linc. A works, B failed miserably. Z

Thanks for your help that was it. Z

Oh if that is it, I'm going to kick myself in the a$$!!!! I moved the TriggerLinc to every corner and floor, thinking that I was not close to an RF access point. I'm give it a try as soon as I get home. Z

So I have a variety of SwitchLincs, LampLincs, AppLincs, etc. and never had any issues adding them to my ISY99ir. I just rcvd a TriggerLinc and can not for the life of me get it added to the ISY. I do have two access points #2443 that I purchased a few years ago with a Remote Linc starter kit, and 3 Dual band SwitchLincs, so I believe I have the RF net covered throughout the house. (and it's only a 5 bedroom house so we are not talking mansion here ) Any helpful troubleshooting hints? Does the PLM connected to the ISY need to be dual band? ISY FW 3.2.6 Z