Happy

I am having a recurring intermittent issue that is driving me crazy. Relating to this problem, I have two scenes defined in my ISY994 v 4.5.4: 1. A switch turns on a few circuits/devices, including an Insteon LED Bulb. 29.8O.27 2. A motion sensor turns on/off 4 of the above mentioned bulbs and turns them back off after 6- seconds, if its dark, as defined by time. The problem is the above referenced Insteon Bulb seems to turn itself on randomly. Or maybe it is turning on with the motion sensor in the middle of the night along with the other bulbs, but not turning itself back off. the problem is typically noticed before I go to bed, or when I get up in the morning... the offending bulb is ON. It wasn't ON when I was in the area earlier, and none of the other bulbs on the motion sensor are on. Any help will be greatly appreciated... suggestions for troubleshooting or anything. I am not an ISY genius, but usually do okay following directions! Also, I've stared at my event viewer this evening and don't see anything screaming at me, but then again, I really don't know what I am looking at. Here is the event viewer with the motion sensor turning all the lights on and back off. Tue 08/29/2017 06:41:09 PM : [ 21 5E 1B 1] DON 1 Tue 08/29/2017 06:41:09 PM : [ 29 82 AA 1] ST 51 Tue 08/29/2017 06:41:09 PM : [ 29 82 14 1] ST 51 Tue 08/29/2017 06:41:09 PM : [ 29 80 27 1] ST 102 Tue 08/29/2017 06:41:09 PM : [ 29 7F B7 1] ST 51 Tue 08/29/2017 06:41:09 PM : [ 21 5E 1B 1] ST 255 Tue 08/29/2017 06:41:40 PM : [ 21 5E 1B 1] DOF 1 Tue 08/29/2017 06:41:40 PM : [ 29 82 AA 1] ST 0 Tue 08/29/2017 06:41:40 PM : [ 29 82 14 1] ST 0 Tue 08/29/2017 06:41:40 PM : [ 29 80 27 1] ST 0 Tue 08/29/2017 06:41:40 PM : [ 29 7F B7 1] ST 0 Tue 08/29/2017 06:41:40 PM : [ 21 5E 1B 1] ST 0 Tue 08/29/2017 06:46:03 PM : [D2D EVENT ] Event [21 5E 1B 1] [DON] [1] uom=0 prec=-1 Tue 08/29/2017 06:46:03 PM : [ 21 5E 1B 1] DON 1 Tue 08/29/2017 06:46:03 PM : [D2D-CMP 0039] CTL [21 5E 1B 1] DON op=1 Event(val=1 uom=0 prec=-1) is Condition(val=0 uom=0 prec=-1) --> true Tue 08/29/2017 06:46:03 PM : [D2D EVENT ] Event [29 82 AA 1] [sT] [51] uom=0 prec=-1 Tue 08/29/2017 06:46:03 PM : [ 29 82 AA 1] ST 51 Tue 08/29/2017 06:46:03 PM : [D2D EVENT ] Event [29 82 14 1] [sT] [51] uom=0 prec=-1 Tue 08/29/2017 06:46:03 PM : [ 29 82 14 1] ST 51 Tue 08/29/2017 06:46:03 PM : [D2D EVENT ] Event [29 80 27 1] [sT] [102] uom=0 prec=-1 Tue 08/29/2017 06:46:03 PM : [ 29 80 27 1] ST 102 Tue 08/29/2017 06:46:03 PM : [D2D EVENT ] Event [29 7F B7 1] [sT] [51] uom=0 prec=-1 Tue 08/29/2017 06:46:03 PM : [ 29 7F B7 1] ST 51 Tue 08/29/2017 06:46:03 PM : [D2D EVENT ] Event [21 5E 1B 1] [sT] [255] uom=0 prec=-1 Tue 08/29/2017 06:46:03 PM : [ 21 5E 1B 1] ST 255 Tue 08/29/2017 06:46:34 PM : [D2D EVENT ] Event [21 5E 1B 1] [DOF] [1] uom=0 prec=-1 Tue 08/29/2017 06:46:34 PM : [ 21 5E 1B 1] DOF 1 Tue 08/29/2017 06:46:34 PM : [D2D-CMP 0035] CTL [21 5E 1B 1] DOF op=1 Event(val=1 uom=0 prec=-1) is Condition(val=0 uom=0 prec=-1) --> true Tue 08/29/2017 06:46:34 PM : [D2D EVENT ] Event [29 82 AA 1] [sT] [0] uom=0 prec=-1 Tue 08/29/2017 06:46:34 PM : [ 29 82 AA 1] ST 0 Tue 08/29/2017 06:46:34 PM : [D2D EVENT ] Event [29 82 14 1] [sT] [0] uom=0 prec=-1 Tue 08/29/2017 06:46:34 PM : [ 29 82 14 1] ST 0 Tue 08/29/2017 06:46:34 PM : [D2D EVENT ] Event [29 80 27 1] [sT] [0] uom=0 prec=-1 Tue 08/29/2017 06:46:34 PM : [ 29 80 27 1] ST 0 Tue 08/29/2017 06:46:34 PM : [D2D EVENT ] Event [29 7F B7 1] [sT] [0] uom=0 prec=-1 Tue 08/29/2017 06:46:34 PM : [ 29 7F B7 1] ST 0 Tue 08/29/2017 06:46:34 PM : [D2D EVENT ] Event [21 5E 1B 1] [sT] [0] uom=0 prec=-1 Tue 08/29/2017 06:46:34 PM : [ 21 5E 1B 1] ST 0 Tue 08/29/2017 06:56:32 PM : [ Time] 18:56:35 58(0) Here is the event viewer reflecting the switch turning ON the scene with the other lights: Tue 08/29/2017 07:03:47 PM : [D2D EVENT ] Event [20 CD A1 1] [DON] [0] uom=0 prec=-1 Tue 08/29/2017 07:03:47 PM : [ 20 CD A1 1] DON 0 Tue 08/29/2017 07:03:47 PM : [D2D EVENT ] Event [20 CD A1 1] [sT] [255] uom=0 prec=-1 Tue 08/29/2017 07:03:47 PM : [ 20 CD A1 1] ST 255 Tue 08/29/2017 07:03:47 PM : [D2D EVENT ] Event [5 97 DA 1] [sT] [255] uom=0 prec=-1 Tue 08/29/2017 07:03:47 PM : [ 5 97 DA 1] ST 255 Tue 08/29/2017 07:03:47 PM : [D2D-CMP 0035] STS [5 97 DA 1] ST op=1 Event(val=255 uom=0 prec=-1) is Condition(val=255 uom=0 prec=-1) --> true Tue 08/29/2017 07:03:47 PM : [D2D EVENT ] Event [5 99 A9 1] [sT] [255] uom=0 prec=-1 Tue 08/29/2017 07:03:47 PM : [ 5 99 A9 1] ST 255 Tue 08/29/2017 07:03:47 PM : [D2D EVENT ] Event [20 FC 63 1] [sT] [255] uom=0 prec=-1 Tue 08/29/2017 07:03:47 PM : [ 20 FC 63 1] ST 255 Tue 08/29/2017 07:03:47 PM : [D2D EVENT ] Event [21 4 64 1] [sT] [102] uom=0 prec=-1 Tue 08/29/2017 07:03:47 PM : [ 21 4 64 1] ST 102 Tue 08/29/2017 07:03:47 PM : [D2D EVENT ] Event [29 80 27 1] [sT] [102] uom=0 prec=-1 Tue 08/29/2017 07:03:47 PM : [ 29 80 27 1] ST 102 And here it is turning the scene off: Tue 08/29/2017 07:05:03 PM : [D2D EVENT ] Event [20 CD A1 1] [DOF] [0] uom=0 prec=-1 Tue 08/29/2017 07:05:03 PM : [ 20 CD A1 1] DOF 0 Tue 08/29/2017 07:05:03 PM : [D2D EVENT ] Event [20 CD A1 1] [sT] [0] uom=0 prec=-1 Tue 08/29/2017 07:05:03 PM : [ 20 CD A1 1] ST 0 Tue 08/29/2017 07:05:03 PM : [D2D EVENT ] Event [5 97 DA 1] [sT] [0] uom=0 prec=-1 Tue 08/29/2017 07:05:03 PM : [ 5 97 DA 1] ST 0 Tue 08/29/2017 07:05:03 PM : [D2D-CMP 0035] STS [5 97 DA 1] ST op=1 Event(val=0 uom=0 prec=-1) is Condition(val=255 uom=0 prec=-1) --> false Tue 08/29/2017 07:05:03 PM : [D2D EVENT ] Event [5 99 A9 1] [sT] [0] uom=0 prec=-1 Tue 08/29/2017 07:05:03 PM : [ 5 99 A9 1] ST 0 Tue 08/29/2017 07:05:03 PM : [D2D EVENT ] Event [20 FC 63 1] [sT] [0] uom=0 prec=-1 Tue 08/29/2017 07:05:03 PM : [ 20 FC 63 1] ST 0 Tue 08/29/2017 07:05:03 PM : [D2D EVENT ] Event [21 4 64 1] [sT] [0] uom=0 prec=-1 Tue 08/29/2017 07:05:03 PM : [ 21 4 64 1] ST 0 Tue 08/29/2017 07:05:03 PM : [D2D EVENT ] Event [29 80 27 1] [sT] [0] uom=0 prec=-1 Tue 08/29/2017 07:05:03 PM : [ 29 80 27 1] ST 0

One more thing... when doing the factory reset it always come back on with with the "B" button lit... this is the ONLY button that I had used in a scene (there is a load on the switch too). Pushing the B button turns the load on. HOlding it turns the load off. Again, this is the "B" button and not the load button. Pushing the load (big puttons at top and bottom) also control the load. This is AFTER a reset and there are No scenes or anything defined using the KPL. The KPL isn't even "added" at this time. Matt

I installed this KPL today. Seemed to work fine. Several hours later it is no longer recognized as a 2487S and is indicating "Unsupported Device 2.44". Really frustrated. Have cleared Java cache. Am running v4.0.5 on ISY 994. Have restored Have queried Have removed KPL and reinstalled. Have deleted and re-added It still works and runs my programs but I can't seem to access Toggle Model (only reason I even noticed that it was showing Unsupported Device is because I was trying to change toggle mode and couldn't find it. FYI, I DID change the toggle mode earlier today, so I know it was there earlier. Help will be greatly appreciated. Matt

I have installed a bunch of insteon switches and an ISY. I'm pretty decent at programming, but am running short of TIME at the some time that I am doing an addition with TONS of ISY automation planned. I really need help programming my system for lights, fans, etc. as well as integrating with Autelis pool and RS485 controls (windows, music, etc.). I am located in Chapel Hill, NC. I'm not sure being near me is important - I think this could be done remotely? Please reply! I need help! Matt Hapgood matt.hapgood@alumni.duke.edu

Has anyone looked into or successfully controlled a Thermasol steam shower with ISY? I am particularly interested in controlling the "Serenity Sound and Light System" with Insteon/ISY controls. Here's a link to the product: http://www.thermasol.com/index.cfm?fuse ... &mItem=187 Matt