Frostbite Posted September 17, 2015 Posted September 17, 2015 *************** EDIT ************************ Problem solved by factory reset of the remote. See posts #2 and #3 below. Thanks for the newbie assist folks ************************************************** Unable to add this new device. New Insteon Device-->Auto Discover gets me the following: The following devices could not be added: 35.00.CF -Cannot determine Insteon Engine Choosing one of the (2) available 2342-222 Device Types (00.12 and 00.1A) gets a similar "Cannot determine Insteon Engine" error. I was originally getting a "device not supported" error, but I manually upgraded the firmware and UI to 4.3.18 per this thread: http://forum.universal-devices.com/topic/16270-insteon-mini-remote-switch-model-2342-242-unsupported/page-4 Info: Insteon 2342-222 Scene Mini Remote 35.00.CF v1.7 1450 Firmware: Insteon_UD994 v4.3.18 UI: Insteon_UD994 v4.3.18 I've cleared Java, etc, etc Log from attempted add: Wed 09/16/2015 08:29:21 PM : [ Time] 20:29:22 0(0) Wed 09/16/2015 08:29:38 PM : [35 0 CF ] Added to list of devices to link to ISY Wed 09/16/2015 08:29:38 PM : [iNST-TX-I1 ] 02 62 35 00 CF 0F 0D 00 Wed 09/16/2015 08:29:38 PM : [iNST-ACK ] 02 62 35.00.CF 0F 0D 00 06 (00) Wed 09/16/2015 08:29:47 PM : [iNST-TX-I1 ] 02 62 35 00 CF 0F 0D 00 Wed 09/16/2015 08:29:47 PM : [iNST-ACK ] 02 62 35.00.CF 0F 0D 00 06 (00) Wed 09/16/2015 08:29:56 PM : [iNST-TX-I1 ] 02 62 35 00 CF 0F 0D 00 Wed 09/16/2015 08:29:56 PM : [iNST-ACK ] 02 62 35.00.CF 0F 0D 00 06 (00) Wed 09/16/2015 08:30:00 PM : [35 0 CF 0 ] Failed to add device, reason 3 Wed 09/16/2015 08:30:00 PM : [All ] Writing 0 bytes to devices Any ideas anyone? I hate to send this bad boy back, I was pretty excited. Thanks in advance.
larryllix Posted September 17, 2015 Posted September 17, 2015 Have you done a factory reset? This is always good practice for any device before linking it to anything. It's done on most devices by powering up the device with a button held down until it stops beeping and bopping.
larryllix Posted September 17, 2015 Posted September 17, 2015 From the manual "The factory reset procedure clears all settings from Mini Remote including INSTEON scenes.1) If possible, unlink (remove) all scene responders prior to performing factory reset2) Turn Mini Remote off (slide power switch to left)3) Press & Hold Set Button4) While continuing to hold the Set Button, turn Mini Remote back on (slide power switch to the right)" It's called "finger twister".
jerlands Posted September 17, 2015 Posted September 17, 2015 Try adding it > Link Management > RemoteLinc 2 > 8 or 4 scene Jon...
Frostbite Posted September 17, 2015 Author Posted September 17, 2015 Wow, no kidding about the twisted fingers... I performed the reset and it is now correctly added Thanks a bunch Larry!!!
larryllix Posted September 17, 2015 Posted September 17, 2015 Wow, no kidding about the twisted fingers... I performed the reset and it is now correctly added Thanks a bunch Larry!!! Good to hear and great for the future forum to get resolutions posted!!
Recommended Posts
Archived
This topic is now archived and is closed to further replies.