Exception in thread using v1.0.0

[johnnyt]

@Jimbo.Automates Am getting errors after uninstalling and reinstalling to get v1.0.0, per this workaround:

 

2022-12-12 21:03:19,507 Thread-19  udi_interface      DEBUG    Controller:add_node: Adding: Guest Bedroom
2022-12-12 21:03:19,508 Thread-19  udi_interface      ERROR    udi_interface:write: Exception in thread

will PM log to you

[johnnyt]

how do I go back? I lost all my airthings nodes in ISY and my programs are all have Node Status [null entry]

 
Then
        Wait  2 seconds
        $sAQ.CO2.MasterBedroom.Value  = Node Status [null entry]
        $sAQ.CO2.MiddleBedroom.Value  = Node Status [null entry]
        $sAQ.CO2.NWBedroom.Value  = Node Status [null entry]
        $sAQ.CO2.SWBedroom.Value  = Node Status [null entry]
        $sAQ.CO2.MainFloor.Value  = Node Status [null entry]
        $sAQ.CO2.RecRoom.Value  = Node Status [null entry]
        Wait  1 second
        $sAQ.VOC.MainFloor.Value  = Node Status [null entry]
        $sAQ.VOC.MasterBedroom.Value  = Node Status [null entry]
        $sAQ.VOC.MiddleBedroom.Value  = Node Status [null entry]
        $sAQ.VOC.NWBedroom.Value  = Node Status [null entry]
        $sAQ.VOC.SWBedroom.Value  = Node Status [null entry]
        $sAQ.VOC.RecRoom.Value  = Node Status [null entry]
        Wait  1 second
        $sTemp.MasterBedroom.Airthings  = Node Status [null entry]
        $sTemp.MasterBedroom.Airthings *= 100
        $sTemp.MiddleBedroom.Airthings  = Node Status [null entry]
        $sTemp.MiddleBedroom.Airthings *= 100
        $sTemp.NWBedroom.Airthings  = Node Status [null entry]
        $sTemp.NWBedroom.Airthings *= 100
        $sTemp.MainFloor.Airthings  = Node Status [null entry]
        $sTemp.MainFloor.Airthings *= 100
        $sTemp.RecRoom.Airthings  = Node Status [null entry]
        $sTemp.RecRoom.Airthings *= 100
        $sTemp.SWBedroom.Airthings  = Node Status [null entry]
        $sTemp.SWBedroom.Airthings *= 100
        Wait  1 second
        $sHum.MainFloor.Airthings  = Node Status [null entry]
        $sHum.MasterBedroom.Airthings  = Node Status [null entry]
        $sHum.MiddleBedroom.Airthings  = Node Status [null entry]
        $sHum.NWBedroom.Airthings  = Node Status [null entry]
        $sHum.RecRoom.Airthings  = Node Status [null entry]
        $sHum.SWBedroom.Airthings  = Node Status [null entry]
        Wait  1 second
        $iAQ.Pressure.MainFloor  = Node Status [null entry]
        $iAQ.Pressure.MasterBedroom  = Node Status [null entry]
        $iAQ.Pressure.MiddleBedroom  = Node Status [null entry]
        $iAQ.Pressure.NWBedroom  = Node Status [null entry]
        $iAQ.Pressure.SWBedroom  = Node Status [null entry]
        $iAQ.Pressure.RecRoom  = Node Status [null entry]
        Wait  1 second
        $sAQ.Radon.MainFloor  = Node Status [null entry]
        $sAQ.Radon.MasterBedrm  = Node Status [null entry]
        $sAQ.Radon.MiddleBedroom  = Node Status [null entry]
        $sAQ.Radon.NWBedroom  = Node Status [null entry]
        $sAQ.Radon.RecRoom  = Node Status [null entry]
        $sAQ.Radon.SWBedroom  = Node Status [null entry]
        $sAQ.Radon.UtilityRoom  = Node Status [null entry]
        Wait  1 second
        $sAQ.HRV.Hum  = Node Status [null entry]
        $sAQ.HRV.Radon  = Node Status [null entry]
        $sAQ.HRV.Temp  = Node Status [null entry]
        $sAQ.HRV.VOC  = Node Status [null entry]
        Wait  1 second
        Send Notification to 'jean' content 'IAQ - Raw Data - HRV'
        Run Program 'Calc AQ Averages and add Weather data' (Then Path)
 
Else
   - No Actions - (To add one, press 'Action')
 

[Jimbo.Automates]

Sorry, you shouldn't have uninstalled, just reinstall in the same slot due to the pg3 issue. Do the nodes not show up in the ISY?

Sent from my Pixel 6 Pro using Tapatalk

[Jimbo.Automates]

Sorry, I see the exception now, missed that. I'll review your log and see if I can get it fixed tonight.

Sent from my Pixel 6 Pro using Tapatalk

[Jimbo.Automates]

Version 1.0.1 released to force an upgrade of the udi_interface which was out of date on your system.

 

[johnnyt]

did the upgrade to 1.0.1 and all the nodes in ISY were restored and my programs see them properly. phew.

all good now. thanks.