aweber1nj Posted February 1 Share Posted February 1 (edited) Trying to exclude/remove some Z-Wave switches from my ISY in preparation to move them, but when I choose Remove a Device, that window just says Listening for Devices and eventually just dismisses itself, not returning anything or doing anything. I did see some SSL errors recently, but not sure what those are all about. ISY v5.3.1 ZWave 6.82.01 / 21100 Any help/tips would be greatly appreciated. Found this in the log, don't know if it helps? ZW 004 Multilevel Switch Error 0.00000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000 Wed 2024/01/31 04:51:36 PM System Log ZW 004 Multilevel Switch Wed 2024/01/31 04:51:36 PM System -2 D R Side board Lights Status 100% Wed 2024/01/31 04:55:06 PM System Log L R Lights 3 Status 50% Wed 2024/01/31 05:20:06 PM System Log ZW Outdoor1 On-Off Error 0.00000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000 Wed 2024/01/31 07:52:50 PM System Log Get NodeDef ZWave 0 Wed 2024/01/31 08:36:34 PM System Log ZW 005 On-Off Power Switch Status On Wed 2024/01/31 08:36:57 PM System Log Start Exclude ZWave Wed 2024/01/31 08:37:15 PM System Log Start Exclude ZWave Wed 2024/01/31 08:39:43 PM System Log Cancel Include/Excl ZWave Wed 2024/01/31 08:40:38 PM System Log Start Exclude ZWave Wed 2024/01/31 08:41:16 PM System Log ZW Outdoor1 On-Off Status Off Wed 2024/01/31 08:44:08 PM System Log ZW Outdoor1 On-Off Status On Wed 2024/01/31 08:44:11 PM System Log ZW Outdoor1 On-Off Status Off Wed 2024/01/31 08:44:17 PM System Log ZW Outdoor1 On-Off Error 0.00000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000 Wed 2024/01/31 08:44:28 PM System Log ZW Outdoor1 On-Off Wed 2024/01/31 08:44:28 PM System -2 [ZWCMD cmd.51] ZWave Wed 2024/01/31 08:44:50 PM System Log [ZWCMD cmd.51] ZWave Wed 2024/01/31 08:44:51 PM System Log [ZWCMD cmd.51] ZWave Wed 2024/01/31 08:44:51 PM System Log [ZWCMD cmd.51] ZWave Wed 2024/01/31 08:45:19 PM System Log [ZWCMD cmd.51] ZWave Wed 2024/01/31 08:45:19 PM System Log [ZWCMD cmd.51] ZWave Wed 2024/01/31 08:45:20 PM System Log Start Exclude ZWave Wed 2024/01/31 08:45:30 PM System Log Get Dongle Version ZWave Wed 2024/01/31 08:50:44 PM System Log Get NodeDef ZWave 0 Wed 2024/01/31 08:55:57 PM System Log ZW Indoor1-On-Off Error 0.00000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000 Wed 2024/01/31 08:57:18 PM System Log ZW Indoor1-On-Off Wed 2024/01/31 08:57:18 PM System -2 Edited February 1 by aweber1nj version info, log info Link to comment Share on other sites More sharing options...
Techman Posted February 1 Share Posted February 1 If you're moving to an EISY and If you're unable to exclude the zwave device(s) you can delete them from the ISY then factory reset the device(s) before including them in the EISY Link to comment Share on other sites More sharing options...
aweber1nj Posted February 2 Author Share Posted February 2 Yeah, this is a very good point. Unfortunately, I have a mish-mosh of different plugs so I'll have to go find the factory reset info for each model. But yes, good idea. Thanks. Link to comment Share on other sites More sharing options...
Recommended Posts