Trying to exclude/remove some Z-Wave switches from my ISY in preparation to move them, but when I choose Remove a Device, that window just says Listening for Devices and eventually just dismisses itself, not returning anything or doing anything.

I did see some SSL errors recently, but not sure what those are all about.

ISY v5.3.1

ZWave 6.82.01 / 21100

Any help/tips would be greatly appreciated.

Found this in the log, don't know if it helps?

ZW 004 Multilevel Switch    Error    0.00000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000    Wed 2024/01/31 04:51:36 PM    System    Log    
ZW 004 Multilevel Switch              Wed 2024/01/31 04:51:36 PM    System    -2    
D R Side board Lights    Status    100%    Wed 2024/01/31 04:55:06 PM    System    Log    
L R Lights 3    Status    50%    Wed 2024/01/31 05:20:06 PM    System    Log    
ZW Outdoor1 On-Off    Error    0.00000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000    Wed 2024/01/31 07:52:50 PM    System    Log    
Get NodeDef    ZWave    0    Wed 2024/01/31 08:36:34 PM    System    Log    
ZW 005 On-Off Power Switch    Status    On    Wed 2024/01/31 08:36:57 PM    System    Log    
Start Exclude    ZWave         Wed 2024/01/31 08:37:15 PM    System    Log    
Start Exclude    ZWave         Wed 2024/01/31 08:39:43 PM    System    Log    
Cancel Include/Excl    ZWave         Wed 2024/01/31 08:40:38 PM    System    Log    
Start Exclude    ZWave         Wed 2024/01/31 08:41:16 PM    System    Log    
ZW Outdoor1 On-Off    Status    Off    Wed 2024/01/31 08:44:08 PM    System    Log    
ZW Outdoor1 On-Off    Status    On    Wed 2024/01/31 08:44:11 PM    System    Log    
ZW Outdoor1 On-Off    Status    Off    Wed 2024/01/31 08:44:17 PM    System    Log    
ZW Outdoor1 On-Off    Error    0.00000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000    Wed 2024/01/31 08:44:28 PM    System    Log    
ZW Outdoor1 On-Off              Wed 2024/01/31 08:44:28 PM    System    -2    
[ZWCMD cmd.51]    ZWave         Wed 2024/01/31 08:44:50 PM    System    Log    
[ZWCMD cmd.51]    ZWave         Wed 2024/01/31 08:44:51 PM    System    Log    
[ZWCMD cmd.51]    ZWave         Wed 2024/01/31 08:44:51 PM    System    Log    
[ZWCMD cmd.51]    ZWave         Wed 2024/01/31 08:45:19 PM    System    Log    
[ZWCMD cmd.51]    ZWave         Wed 2024/01/31 08:45:19 PM    System    Log    
[ZWCMD cmd.51]    ZWave         Wed 2024/01/31 08:45:20 PM    System    Log    
Start Exclude    ZWave         Wed 2024/01/31 08:45:30 PM    System    Log    
Get Dongle Version    ZWave         Wed 2024/01/31 08:50:44 PM    System    Log    
Get NodeDef    ZWave    0    Wed 2024/01/31 08:55:57 PM    System    Log    
ZW Indoor1-On-Off    Error    0.00000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000    Wed 2024/01/31 08:57:18 PM    System    Log    
ZW Indoor1-On-Off              Wed 2024/01/31 08:57:18 PM    System    -2    
 

Edited February 1, 20241 yr by aweber1nj
version info, log info

If you're moving to an EISY and If you're unable to exclude the zwave device(s) you can delete them from the ISY then factory reset the device(s) before including them in the EISY

Yeah, this is a very good point.  Unfortunately, I have a mish-mosh of different plugs so I'll have to go find the factory reset info for each model.  But yes, good idea.  Thanks.