ldrinc

Sorry about that. Took me awhile to figure out how to correctly add an attachment.

Can someone help me understand what the grayed out symbol means in the image attached?

Thanks all... Your suggestions fixed my issue. Thanks again.

Hi All Need help with a simple program. I'd like my hidden door sensor to trigger a hallway light to come for 5 minutes when the sensor is switched on. This is what I have so far test sensor - [ID 014B][Parent 0032] If Status '32.7A.4D.1 - Door Sensor' is Off Then Set 'Master Bedroom / M/Bedroom light' On Else - No Actions - (To add one, press 'Action')

ok, I figured it out everything works as it should. Here is what I did. The settings for the IP2SL should be as follows. Serial Parameters : Multiple Ports Enabled Baud Rate 57.600 Flow Control None Stop Bits 1 Parity None Data Bits 8 Frame Errors "0" Parity Errors "0" Overflow Errors "0" Previously, I had "Multiple Ports" disabled

I am having trouble creating a resource for powering on/off my KD 4x4 Matrix Switcher. Can anyone help me with how to setup and format the command in the resource. attached are some particulars from the KD manual. Also, I am using a Global Cache Itach IP2SL to transmit the command via the ISY. I have setup the IP2SL with the following parameters. Baud rate: 57,600 Data Bits: 8 Parity: None Stop Bits: 1 Flow Control: None Carriage Return: Required Following is the network resource that I have created. TCP 192.168.1.16 Port = 4999 timeout = 500 ms C-Escaped Body = PF\r\n Actual = PF The error in the ISY log is as follow: [TCP-Conn] -1/-140002, Net Module Rule: 226 What am I missing?

That is correct. I am talking about a potential failure of the A/C system not the thermostat in this case.

The TSTAT is located in my vacation home three hundred miles away. The program that I was suggesting is to prevent further damage (if any) until I can have the unit checked out.

I have three Venstar thermostats in my home. All three have the Insteon Venstar Adapters attached to them. In the past I have had a situation where my hvac units where failing causing the temperature on the thermostat to rise higher which made the AC unit run non stop. I would like to put a protect program in the isy to have the TStats turn off if the AC if temperature in the home reaches a certain point in the summer. Below is my attempt at this programming. Am I on the right track with programming? Is there anything that you could add/subtract? If Status 'First Floor Thermostat' > Mode Cool And Status 'First Floor Thermostat' > 77° (Temperature) Then Set 'First Floor Thermostat' Mode Off Send Notification to 'Default' content 'First Floor Thermostat' Else - No Actions - (To add one, press 'Action')

Can someone help me with the command structure(syntax) for issuing an RS232 command via the ISY. I already have the ISY994i with the networking module installed and I know how to create the resource but not so sure what to use to execute the command (http, tcp, etc). Any help would be appreciated. The device that I am trying to control is my Key Digital Matrix Switch. When I set up the GC IP2SL the manufacturer suggests that the following settings be applied: » Baud rate: 57,600 » Data Bits: 8 » Parity: None » Stop Bits: 1 » Flow Control: None » Carriage Return: Required » Line Feed: Required The command that I would like to use to create an ISY resource for will switch Output 3 to Input 1. The command that I should use is SPO01SI03. How do I write this command in the isy resource?

When moving to the configuration tab in my isy admin console. I get the following messages in the event viewer. Wed 04/22/2015 09:58:40 PM : [FileOpen ] Open failed for [/CONF/ELK.CNF] ® Wed 04/22/2015 09:58:42 PM : [FileOpen ] Open failed for [/CONF/ELK.CNF] ® Wed 04/22/2015 09:58:43 PM : [FileOpen ] Open failed for [/CONF/ELK.CNF] ® Wed 04/22/2015 09:58:44 PM : [FileOpen ] Open failed for [/CONF/ELK.CNF] ® Is this normal? If not, how do I fix this?

All, I have one thing to say.... FANTASTIC!!! You guys are awesome. Turns out that I had a corrupt sd card. I changed it out for a new one and restored a backup. Everything is back the way it was. Thank you very much for your prompt responses...

Not sure if you can identify the problem by the lights but I have 3 solid blue lights (power, rx, tx) on and 1 red flashing led dl

Did that.... Same thing. Blinking Red LED

Updated to the latest RC thinking that it would solve problems that I was having with "Options" not showing up on the admin console. When that didnt help I wanted to go back to the previous stable firmware.

After an unsuccessful attempt to restore my isy to a previous file. the red light keeps blinking and I am unable to connect to my isy. Please advise. I have done a power cycle but have not had any luck with it.

Michel, I am using a voice control software by the name of VoxCommando. Currently, I have it executing programs and commands in my ISY nicely. I'd like to have the VoxCommando software monitor events that take place in the isy such as when a motion detector is triggered so that it will speak to me when it does.

I am trying to use a program to watch for events in order to trigger a program. Is there a way to have this program subscribe to my ISY for events?

Ok, I think I understand now. My apology for not being clear. I am working from a different computer and off of my memory at the moment and I do not have remote access to my isy to see the program that I created. That said, I will post a reply this evening when I get access to my isy.

Xathros, Thanks for the reply. Not sure I understand your question. The only program that calls the resource is as follows: Open XBMC (program) run if if MCE = 0 and XBMC = 0 Then Resouce XBMC (Open XBMC)

Looking for help with writing a program in my isy994i that will identify the state, when and if a program was executed. In a nutshell, I have two applications that I controll via my isy... XBMC and Windows MCE. Using network resources I have successfully created a program that will launch and close both applications. The problem that I am running into is that I'm not able to identify the state of these programs. Nonetheless, After doing some reading through the wiki and some threads I don't fully understand how to use the variable options that are available. My ultimate goal is to prevent both XBMC and MCE from running at the same time. Here is what I have tried so far that doesn't seem to work. Network Resources that were created include: * Open XBMC XBMC variable state = 1 * Close XBMC XBMC variable state = 0 * Open MCE MCE variable state = 1 * Close MCE MCE variable state = 0 Program created *Open XBMC IF MCE = 0 and XBMC = 0 Then Resouce XBMC (Open XBMC) When I run the if statement all it does is open and closes both applications repeatedly and it won't stop until I reset the HTPC. Any help with resolving this looping issue would be appreciated.