f.demello

Thanks Brian. It appears you have to hit the Refresh button at upper right to show the On. Still no luck on e-mails/texts. I keep trying the units by testing a wet condition. This worked with my first unit (immediately received a text). Not sure it I am doing anything wrong. I am assuming all I have to do is put the contacts on a damp sponge/bit of water to trigger the Wet signal (or at least that is what I think I did with the 1st one). Am I missing something? Thanks again

Having a small issue with the text/e-mail notifications. It worked on the activation of my first leak sensor but not on the subsequent 2. I did notice that for the Leak Startup program I am not sure ENABLE RUN AT START-UP is activated. When I right click the program on the summary page and select it "Enable Run At Startup", it does not appear to update the status to On in the Run At Startup column (see below) - it also appears this has never run . How can I be sure it is Enabled and working? Thank you

Thanks a lot guys!

Does anyone know how to get the brackets in this Leak Sensor Problem condition statement? If ( Time is 9:00:00AM Or Time is 6:00:00PM ) And ( $sLeakKitchenSink is not 1 Or $sLeakStorageRoom is not 1 ) See below for what I have - can't get the remainder and not sure what I am doing wrong: Thank you

Hello Michael - I opened a 2nd leak sensor, found the address and linked it. Once confusing thing to me is it adds 3 instances (Wet, Dry, Heartbeat) of the device. If every device did this it could get complicated. Should/ca you create a folder for each device? I am assuming if I want to get a text message when there is a leak I need to interface with Wet? Thank you for your help

Connected

Hello 25.29.42 V9B

Have installed the 2 new Access Points. They are on opposite phases. Have added a FilterLinc to my comouter equipment. I am still having 0 luck installing the Leak Sensors. I also cannot find a Address inside the unit to try manually. I'm about $900 in and can only get one device to link. Pretty frustrated and not sure what to try next. Any help will be appreciated

I am a little confused on what to buy. From what I am reading you want 2 access points to join the 2 phases of an electrical system. However any dual band unit is already an access point. Isn't the PLM a dual band unit serving as one access point? If you have an odd # does it break the phase join that 2 devices perform? I am also confused on placement of these devices. My initial thought would be you would want them spread out (IE 1 on each floor) to get the best coverage but from reading I am not sure. It appears it bridges RF/Power Line so they essentially could be close together. Correct? Or is it better to spread out as long as the phases are joined? Thank you

Thank you guys for the information and advice. I will add a couple of access points to help the communication. I am assuming this is the correct unit (2443 Access Point - INSTEON Range Extender Dual-Band). Hopefully that will help

Thank you. Moved the ISY/PLM back to my lower level and I was able to get the Appliance link to be seen/added No luck with a Link Sensor (will try to add manually) or a motion detector. What does the device address look like once I open up the unit? Any trick on hte moton? I am a little confused on what a Responder means. I assume you make a device a responder to events of another device (s) Correct? Thanks again

OK I tried that: Start Linking Put ApplianceLinc into linking mode - flashes repeatedly Select Remove Links Finish Nothing No matter what I do nothing seems to complete the link. No devices are visible in the admin console

Thanks for the help I do get the Admin Console AND that 2nd window (which is new - never had that before). I would normally use Start Linking. I would get the 2nd window and select Remove Links. I would normally Start Linking after I put the device into linking mode

Instead of opening the leak sensor I had a new ApplianceLinc (#2456S3) come in and tried that instead. Thought that would be easy. Cannot get the ISY to see it. Moved the ISY/PLM closer to my computer so I could test this out. All devices are right next to these units. Not only will it not see anything but I am getting this 2nd window popping up when I launch the Admin Console (see attached) Not sure where to go next Any help will be appreciated. Thank you

Hello - I have the above dual band unit and have been unable to get the system to see my first device - Leak Sensor (2852-222). I have placed the unit in program mode directly near the PLM to no avail. My Admin Console connects no problem. When I Start Syncing I get the Remove Links dialog but nothing happens after I click Finish. I tried to manually connect but I do not know where to find the address of the device Anything I can try to get the unit connected? Noet: PLM Version 25.29.42 V9B Thank you