EWhite Posted December 16, 2023 Share Posted December 16, 2023 here is my code..: {"id": "Temp1", "type": "TempHumid", "sensor_id": "AM2301", "status_topic": "tele/Temp1/SENSOR", "cmd_topic": "cmnd/Temp1/power"}, and here is my MQTT that im trying to pull from..: 13:26:02.357 MQT: tele/Temp1/STATE = {"Time":"2023-12-16T13:26:02","Uptime":"7T16:22:52","UptimeSec":663772,"Heap":25,"SleepMode":"Dynamic","Sleep":50,"LoadAvg":19,"MqttCount":5,"POWER":"OFF","Wifi":{"AP":1,"SSId":"nsa_surveillance_32","BSSId":"1E:21:B4:49:DF:B2","Channel":8,"Mode":"11n","RSSI":94,"Signal":-53,"LinkCount":5,"Downtime":"0T00:02:33"}} 13:26:02.404 MQT: tele/Temp1/SENSOR = {"Time":"2023-12-16T13:26:02","ANALOG":{"Range":1187},"AM2301":{"Temperature":42.1,"Humidity":85.5,"DewPoint":38.0},"TempUnit":"F"} it gives me an error in the log : 2023-12-16 13:24:37,620 MQTT udi_interface.interface DEBUG interface:_message: QUEUING incoming message shortPoll 2023-12-16 13:24:37,622 Command udi_interface.interface DEBUG interface:_parseInput: DEQUEING shortPoll 2023-12-16 13:25:02,789 Thread-6 udi_interface DEBUG mqtt-poly:_on_message: Received _on_message {"Time":"2023-12-16T13:25:02","ANALOG":{"Range":1187},"AM2301":{"Temperature":42.1,"Humidity":85.4,"DewPoint":38.0},"TempUnit":"F"} from tele/Temp1/SENSOR 2023-12-16 13:25:02,791 Thread-6 udi_interface INFO mqtt-poly:_on_message: ANALOG Payload = {"Time":"2023-12-16T13:25:02","ANALOG":{"Range":1187},"AM2301":{"Temperature":42.1,"Humidity":85.4,"DewPoint":38.0},"TempUnit":"F"}, Topic = tele/Temp1/SENSOR 2023-12-16 13:25:02,791 Thread-6 udi_interface INFO mqtt-poly:_on_message: _OA: Range 2023-12-16 13:25:02,792 Thread-6 udi_interface DEBUG mqtt-poly:_get_device_address_from_sensor_id: GDA1: tele/Temp1/SENSOR Range 2023-12-16 13:25:02,793 Thread-6 udi_interface DEBUG mqtt-poly:_get_device_address_from_sensor_id: DLT: [{'id': 'shopstorage', 'type': 'switch', 'status_topic': 'stat/shopstorage/POWER', 'cmd_topic': 'cmnd/shopstorage/power'}, {'id': 'shopoutside', 'type': 'switch', 'status_topic': 'stat/shopsouthwall/POWER1', 'cmd_topic': 'cmnd/shopsouthwall/POWER1'}, {'id': 'shopmain', 'type': 'switch', 'status_topic': 'stat/shopsouthwall/POWER2', 'cmd_topic': 'cmnd/shopsouthwall/POWER2'}, {'id': 'sonoff1', 'type': 'TempHumid', 'sensor_id': 'AM2301', 'status_topic': 'tele/sonoff1/SENSOR', 'cmd_topic': 'cmnd/sonoff1/power'}, {'id': 'sonoff2', 'type': 'switch', 'status_topic': 'stat/sonoff1/POWER', 'cmd_topic': 'cmnd/sonoff1/power'}, {'id': 'Temp1', 'type': 'TempHumid', 'sensor_id': 'AM2301', 'status_topic': 'tele/Temp1/SENSOR', 'cmd_topic': 'cmnd/Temp1/power'}, {'id': 'Temp2', 'type': 'switch', 'status_topic': 'stat/Temp1/POWER', 'cmd_topic': 'cmnd/Temp1/power'}, {'id': 'Temp3', 'type': 'analog', 'sensor_id': 'Range', 'status_topic': 'tele/Temp1/SENSOR', 'cmd_topic': 'cmnd/Temp1/power'}, {'id': 'ST1', 'type': 'TempHumid', 'sensor_id': 'AM2301', 'status_topic': 'tele/StorageTrailer/SENSOR', 'cmd_topic': 'cmnd/StorageTrailer/power'}, {'id': 'ST2', 'type': 'switch', 'status_topic': 'stat/StorageTrailer/POWER', 'cmd_topic': 'cmnd/StorageTrailer/power'}, {'id': 'STlights', 'type': 'switch', 'status_topic': 'stat/TrailerLights/POWER', 'cmd_topic': 'cmnd/TrailerLights/command/power'}, {'id': 'DeckLites', 'type': 'switch', 'status_topic': 'stat/decklitesplug/POWER', 'cmd_topic': 'cmnd/decklitesplug/power'}, {'id': 'ShopHeatLamp', 'type': 'switch', 'status_topic': 'stat/ShopHeatLamp/POWER', 'cmd_topic': 'cmnd/ShopHeatLamp/power'}] 2023-12-16 13:25:02,794 Thread-6 udi_interface DEBUG mqtt-poly:_get_device_address_from_sensor_id: GDA2: {'id': 'shopstorage', 'type': 'switch', 'status_topic': 'stat/shopstorage/POWER', 'cmd_topic': 'cmnd/shopstorage/power'} 2023-12-16 13:25:02,795 Thread-6 udi_interface DEBUG mqtt-poly:_get_device_address_from_sensor_id: GDA2: {'id': 'shopoutside', 'type': 'switch', 'status_topic': 'stat/shopsouthwall/POWER1', 'cmd_topic': 'cmnd/shopsouthwall/POWER1'} 2023-12-16 13:25:02,796 Thread-6 udi_interface DEBUG mqtt-poly:_get_device_address_from_sensor_id: GDA2: {'id': 'shopmain', 'type': 'switch', 'status_topic': 'stat/shopsouthwall/POWER2', 'cmd_topic': 'cmnd/shopsouthwall/POWER2'} 2023-12-16 13:25:02,797 Thread-6 udi_interface DEBUG mqtt-poly:_get_device_address_from_sensor_id: GDA2: {'id': 'sonoff1', 'type': 'TempHumid', 'sensor_id': 'AM2301', 'status_topic': 'tele/sonoff1/SENSOR', 'cmd_topic': 'cmnd/sonoff1/power'} 2023-12-16 13:25:02,798 Thread-6 udi_interface DEBUG mqtt-poly:_get_device_address_from_sensor_id: GDA2: {'id': 'sonoff2', 'type': 'switch', 'status_topic': 'stat/sonoff1/POWER', 'cmd_topic': 'cmnd/sonoff1/power'} 2023-12-16 13:25:02,799 Thread-6 udi_interface DEBUG mqtt-poly:_get_device_address_from_sensor_id: GDA2: {'id': 'Temp1', 'type': 'TempHumid', 'sensor_id': 'AM2301', 'status_topic': 'tele/Temp1/SENSOR', 'cmd_topic': 'cmnd/Temp1/power'} 2023-12-16 13:25:02,800 Thread-6 udi_interface DEBUG mqtt-poly:_get_device_address_from_sensor_id: GDA2: {'id': 'Temp2', 'type': 'switch', 'status_topic': 'stat/Temp1/POWER', 'cmd_topic': 'cmnd/Temp1/power'} 2023-12-16 13:25:02,800 Thread-6 udi_interface ERROR mqtt-poly:_on_message: Failed to process message 'sensor_id' hope this helps you figure out what i did wrong.. hehehe my Analog Range is working .. just temp and humid not. Quote Link to comment
EWhite Posted December 18, 2023 Author Share Posted December 18, 2023 @TriLife any ideas? I really need this temp and humidity working for my chickens in this cold weather.... Quote Link to comment
TriLife Posted December 20, 2023 Share Posted December 20, 2023 (edited) On 12/18/2023 at 6:54 PM, EWhite said: @TriLife any ideas? I really need this temp and humidity working for my chickens in this cold weather.... Hi @EWhite, Sorry just saw this. Please apologize to your chickens! Ok, let me have a look at what's going on. Question: which Tasmota device are you using? WeMos D1, if I recall correctly? Only Analog and AM2301 on the device? Exactly what are the symptoms? Also, do you have access to Discord? That might speed up troubleshooting Cheers. Edited December 20, 2023 by TriLife added missing information Quote Link to comment
TriLife Posted December 20, 2023 Share Posted December 20, 2023 @EWhite; Can you please send me your complete devfile.yaml? Thanks Quote Link to comment
TriLife Posted December 20, 2023 Share Posted December 20, 2023 Hi @EWhite; I have a temporary fix for you in the Beta Store, Version 0.0.31: The trick is that if you have a type "switch" in the same topic as the type "ANALOG", "AM2301" etc, you MUST put the definition of the type "switch" AFTER the analog etc. Like so: devices: - id: "TurbRange" name: "CrkTurbRange" type: "analog" sensor_id: "Range" status_topic: "tele/Creek/SENSOR" cmd_topic: "cmnd/Creek/POWER" - id: "SluiceTH" name: "CrkSluiceTH" type: "TempHumid" sensor_id: "AM2301" status_topic: "tele/Creek/SENSOR" cmd_topic: "cmnd/Creek/power" - id: "Wemos32A1" name: "Wemos 32 A1" type: "analog" sensor_id: "A1" status_topic: "tele/Wemos32/SENSOR" cmd_topic: "cmnd/Wemos32/POWER" - id: "Wemos32A2" name: "Wemos 32 A2" type: "analog" sensor_id: "A2" status_topic: "tele/Wemos32/SENSOR" cmd_topic: "cmnd/Wemos32/POWER" - id: "Wemos32T1" name: "Wemos 32 T1" type: "Temp" sensor_id: "DS18B20-1" status_topic: "tele/Wemos32/SENSOR" cmd_topic: "cmnd/Wemos32/POWER" - id: "Wemos32T2" name: "Wemos 32 T2" type: "Temp" sensor_id: "DS18B20-2" status_topic: "tele/Wemos32/SENSOR" cmd_topic: "cmnd/Wemos32/POWER" - id: "Wemos32TH32" name: "Wemos 32 TH32" type: "TempHumid" sensor_id: "AM2301" status_topic: "tele/Wemos32/SENSOR" cmd_topic: "cmnd/Wemos32/POWER" #SWITCH TYPES AT THE END - id: "Wemos32SW" name: "Wemos 32 SW" type: "switch" # sensor_id: "AM2301" status_topic: "stat/Wemos32/POWER" cmd_topic: "cmnd/Wemos32/power" - id: "Sluice" name: "Creek Sluice" type: "switch" status_topic: "stat/Creek/POWER" cmd_topic: "cmnd/Creek/power" Please download and verify. In the mean-time, I'll try to figure out, why the order matters. Cheers. Quote Link to comment
EWhite Posted December 20, 2023 Author Share Posted December 20, 2023 (edited) [ {"id": "shopstorage", "type": "switch", "status_topic": "stat/shopstorage/POWER", "cmd_topic": "cmnd/shopstorage/power"}, {"id": "shopoutside", "type": "switch", "status_topic": "stat/shopsouthwall/POWER1", "cmd_topic": "cmnd/shopsouthwall/POWER1"}, {"id": "shopmain", "type": "switch", "status_topic": "stat/shopsouthwall/POWER2", "cmd_topic": "cmnd/shopsouthwall/POWER2"}, {"id": "Temp1", "type": "TempHumid", "sensor_id": "AM2301", "status_topic": "tele/Temp1/SENSOR", "cmd_topic": "cmnd/Temp1/power"}, {"id": "Temp2", "type": "switch", "status_topic": "stat/Temp1/POWER", "cmd_topic": "cmnd/Temp1/power"}, {"id": "Temp3", "type": "analog", "sensor_id": "Range", "status_topic": "tele/Temp1/SENSOR", "cmd_topic": "cmnd/Temp1/power"}, {"id": "ST1", "type": "TempHumid", "sensor_id": "AM2301", "status_topic": "tele/StorageTrailer/SENSOR", "cmd_topic": "cmnd/StorageTrailer/power"}, {"id": "ST2", "type": "switch", "status_topic": "stat/StorageTrailer/POWER", "cmd_topic": "cmnd/StorageTrailer/power"}, {"id": "STlights", "type": "switch", "status_topic": "stat/TrailerLights/POWER", "cmd_topic": "cmnd/TrailerLights/command/power"}, {"id": "DeckLites", "type": "switch", "status_topic": "stat/decklitesplug/POWER", "cmd_topic": "cmnd/decklitesplug/power"}, {"id": "ShopHeatLamp", "type": "switch", "status_topic": "stat/ShopHeatLamp/POWER", "cmd_topic": "cmnd/ShopHeatLamp/power"} ] so i would need to re-arrange these? this is what i have now.. as you can see.. i have 1 analog, 1 temphumid, and 1 switch all on one device. They are all wemos d1 mini units. Edited December 20, 2023 by EWhite Quote Link to comment
EWhite Posted December 20, 2023 Author Share Posted December 20, 2023 edited and arranged all the above.. but .31 is not showing in the store... Quote Link to comment
Solution TriLife Posted December 20, 2023 Solution Share Posted December 20, 2023 (edited) Hi @EWhite, In the meantime, I think I fixed the bug that requires a certain order. I tested it with "switch" front and back. I just pushed the update to the beta store and installed it on my box from there. Still V0.0.31) Can you please confirm? Edited December 20, 2023 by TriLife added missing information Quote Link to comment
EWhite Posted December 20, 2023 Author Share Posted December 20, 2023 It is still just showing .30 for me...i even logged out and back in, refreshed several times...does it take a bit for it to get thru system? Quote Link to comment
TriLife Posted December 20, 2023 Share Posted December 20, 2023 (edited) 1 minute ago, EWhite said: It is still just showing .30 for me...i even logged out and back in, refreshed several times...does it take a bit for it to get thru system? did you clickREFRESH STORE SORRY, yes, it can take a bit to refresh... Edited December 20, 2023 by TriLife added missing information Quote Link to comment
EWhite Posted December 20, 2023 Author Share Posted December 20, 2023 yup.. and it finally showed up.. installing now and testing. Quote Link to comment
EWhite Posted December 20, 2023 Author Share Posted December 20, 2023 YES!!!! it seems to be working.. thanks much! Quote Link to comment
TriLife Posted December 20, 2023 Share Posted December 20, 2023 YAY! Apologies to the chickens again! Let me know, if you have any other issues/ideas. Please make sure you mention @TriLife, and keep posting to this thread. Cheers Quote Link to comment
EWhite Posted December 20, 2023 Author Share Posted December 20, 2023 will do .. thanks again! Quote Link to comment
EWhite Posted December 20, 2023 Author Share Posted December 20, 2023 and the chickens will survive..they are extremely pampered anyways! hehe automatic doors, waterer, feeder and then a climate controlled hacienda! Quote Link to comment
TriLife Posted December 20, 2023 Share Posted December 20, 2023 1 hour ago, EWhite said: and the chickens will survive..they are extremely pampered anyways! hehe automatic doors, waterer, feeder and then a climate controlled hacienda! Nice life! Happy Holidays Quote Link to comment
EWhite Posted December 25, 2023 Author Share Posted December 25, 2023 @TriLife Trying to upgrade the chicken coop Wemos...its been flaky a bit.. So i have a new one started, with relay, and a BME280 module for temp and humid, and the analog for battery. Problem is the BME280 sensor is not working, i added the sensor id to the statement and still nothing. it also reports a dewpoint but that doesnt show up in the AC at all. my MQTT statements from wemos: 21:32:06.392 MQT: tele/ChickCoop/STATE = {"Time":"2023-12-25T21:32:06","Uptime":"0T00:45:09","UptimeSec":2709,"Heap":20,"SleepMode":"Dynamic","Sleep":50,"LoadAvg":19,"MqttCount":1,"POWER":"OFF","Wifi":{"AP":1,"SSId":"IoT_whitehouse","BSSId":"1E:51:B4:49:DF:AE","Channel":4,"Mode":"11n","RSSI":100,"Signal":-33,"LinkCount":1,"Downtime":"0T00:00:03"}} 21:32:06.440 MQT: tele/ChickCoop/SENSOR = {"Time":"2023-12-25T21:32:06","ANALOG":{"Range":1224},"BME280":{"Temperature":72.9,"Humidity":39.7,"DewPoint":46.9,"Pressure":973.5},"PressureUnit":"hPa","TempUnit":"F"} my statements in Nodeserver : [ {"id": "Temp1", "type": "TempHumid", "sensor_id": "AM2301", "status_topic": "tele/Temp1/SENSOR", "cmd_topic": "cmnd/Temp1/power"}, {"id": "ChickCoop1", "type": "TempHumidPress", "sensor_id": "BME280", "status_topic": "tele/ChickCoop/SENSOR", "cmd_topic": "cmnd/ChickCoop/power"}, {"id": "Temp3", "type": "analog", "sensor_id": "Range", "status_topic": "tele/Temp1/SENSOR", "cmd_topic": "cmnd/Temp1/power"}, {"id": "ChickCoop2", "type": "analog", "sensor_id": "Range", "status_topic": "tele/ChickCoop/SENSOR", "cmd_topic": "cmnd/ChickCoop/power"}, {"id": "ST1", "type": "TempHumid", "sensor_id": "AM2301", "status_topic": "tele/StorageTrailer/SENSOR", "cmd_topic": "cmnd/StorageTrailer/power"}, {"id": "ST2", "type": "switch", "status_topic": "stat/StorageTrailer/POWER", "cmd_topic": "cmnd/StorageTrailer/power"}, {"id": "shopstorage", "type": "switch", "status_topic": "stat/shopstorage/POWER", "cmd_topic": "cmnd/shopstorage/power"}, {"id": "shopoutside", "type": "switch", "status_topic": "stat/shopsouthwall/POWER1", "cmd_topic": "cmnd/shopsouthwall/POWER1"}, {"id": "shopmain", "type": "switch", "status_topic": "stat/shopsouthwall/POWER2", "cmd_topic": "cmnd/shopsouthwall/POWER2"}, {"id": "Temp2", "type": "switch", "status_topic": "stat/Temp1/POWER", "cmd_topic": "cmnd/Temp1/power"}, {"id": "ChickCoop3", "type": "switch", "status_topic": "stat/ChickCoop/POWER", "cmd_topic": "cmnd/ChickCoop/power"}, {"id": "STlights", "type": "switch", "status_topic": "stat/TrailerLights/POWER", "cmd_topic": "cmnd/TrailerLights/command/power"}, {"id": "DeckLites", "type": "switch", "status_topic": "stat/decklitesplug/POWER", "cmd_topic": "cmnd/decklitesplug/power"}, {"id": "ShopHeatLamp", "type": "switch", "status_topic": "stat/ShopHeatLamp/POWER", "cmd_topic": "cmnd/ShopHeatLamp/power"}, {"id": "EriksLight", "type": "switch", "status_topic": "stat/EriksFan/POWER1", "cmd_topic": "cmnd/EriksFan/power1"}, {"id": "EriksFan", "type": "ifan", "status_topic": "stat/EriksFan/Result", "cmd_topic": "cmnd/EriksFan/FanSpeed"} ] the ChickCoop# are the new module im trying to add. analog and switch(relay) are working great.. Quote Link to comment
TriLife Posted December 25, 2023 Share Posted December 25, 2023 18 minutes ago, EWhite said: @TriLife Trying to upgrade the chicken coop Wemos...its been flaky a bit.. So i have a new one started, with relay, and a BME280 module for temp and humid, and the analog for battery. Problem is the BME280 sensor is not working, i added the sensor id to the statement and still nothing. it also reports a dewpoint but that doesnt show up in the AC at all. my MQTT statements from wemos: 21:32:06.392 MQT: tele/ChickCoop/STATE = {"Time":"2023-12-25T21:32:06","Uptime":"0T00:45:09","UptimeSec":2709,"Heap":20,"SleepMode":"Dynamic","Sleep":50,"LoadAvg":19,"MqttCount":1,"POWER":"OFF","Wifi":{"AP":1,"SSId":"IoT_whitehouse","BSSId":"1E:51:B4:49:DF:AE","Channel":4,"Mode":"11n","RSSI":100,"Signal":-33,"LinkCount":1,"Downtime":"0T00:00:03"}} 21:32:06.440 MQT: tele/ChickCoop/SENSOR = {"Time":"2023-12-25T21:32:06","ANALOG":{"Range":1224},"BME280":{"Temperature":72.9,"Humidity":39.7,"DewPoint":46.9,"Pressure":973.5},"PressureUnit":"hPa","TempUnit":"F"} my statements in Nodeserver : [ {"id": "Temp1", "type": "TempHumid", "sensor_id": "AM2301", "status_topic": "tele/Temp1/SENSOR", "cmd_topic": "cmnd/Temp1/power"}, {"id": "ChickCoop1", "type": "TempHumidPress", "sensor_id": "BME280", "status_topic": "tele/ChickCoop/SENSOR", "cmd_topic": "cmnd/ChickCoop/power"}, {"id": "Temp3", "type": "analog", "sensor_id": "Range", "status_topic": "tele/Temp1/SENSOR", "cmd_topic": "cmnd/Temp1/power"}, {"id": "ChickCoop2", "type": "analog", "sensor_id": "Range", "status_topic": "tele/ChickCoop/SENSOR", "cmd_topic": "cmnd/ChickCoop/power"}, {"id": "ST1", "type": "TempHumid", "sensor_id": "AM2301", "status_topic": "tele/StorageTrailer/SENSOR", "cmd_topic": "cmnd/StorageTrailer/power"}, {"id": "ST2", "type": "switch", "status_topic": "stat/StorageTrailer/POWER", "cmd_topic": "cmnd/StorageTrailer/power"}, {"id": "shopstorage", "type": "switch", "status_topic": "stat/shopstorage/POWER", "cmd_topic": "cmnd/shopstorage/power"}, {"id": "shopoutside", "type": "switch", "status_topic": "stat/shopsouthwall/POWER1", "cmd_topic": "cmnd/shopsouthwall/POWER1"}, {"id": "shopmain", "type": "switch", "status_topic": "stat/shopsouthwall/POWER2", "cmd_topic": "cmnd/shopsouthwall/POWER2"}, {"id": "Temp2", "type": "switch", "status_topic": "stat/Temp1/POWER", "cmd_topic": "cmnd/Temp1/power"}, {"id": "ChickCoop3", "type": "switch", "status_topic": "stat/ChickCoop/POWER", "cmd_topic": "cmnd/ChickCoop/power"}, {"id": "STlights", "type": "switch", "status_topic": "stat/TrailerLights/POWER", "cmd_topic": "cmnd/TrailerLights/command/power"}, {"id": "DeckLites", "type": "switch", "status_topic": "stat/decklitesplug/POWER", "cmd_topic": "cmnd/decklitesplug/power"}, {"id": "ShopHeatLamp", "type": "switch", "status_topic": "stat/ShopHeatLamp/POWER", "cmd_topic": "cmnd/ShopHeatLamp/power"}, {"id": "EriksLight", "type": "switch", "status_topic": "stat/EriksFan/POWER1", "cmd_topic": "cmnd/EriksFan/power1"}, {"id": "EriksFan", "type": "ifan", "status_topic": "stat/EriksFan/Result", "cmd_topic": "cmnd/EriksFan/FanSpeed"} ] the ChickCoop# are the new module im trying to add. analog and switch(relay) are working great.. Hi @EWhite; Merry Christmas! the BME280 not working is not surprising: I have not updated the plugin for the BME280... I would need to order a unit from Amazon for that, in order to troupbleshoot it here. No problem doing that (you can send me some Amazon bucks $15.90), but it would take a couple of weeks to get here... I can try to do it without a test unit as well, and use you as a guinea pig, if you're up to it. Let me know, what you wanto to do. Cheers; Quote Link to comment
EWhite Posted December 25, 2023 Author Share Posted December 25, 2023 im up for it.. hehehe..i thot the original had BME280 support but dunno if it ever worked or not.. this is first time messing with that unit.. Quote Link to comment
EWhite Posted December 25, 2023 Author Share Posted December 25, 2023 here is screenshot of all the info from MQTT Explorer: Quote Link to comment
TriLife Posted December 25, 2023 Share Posted December 25, 2023 39 minutes ago, EWhite said: im up for it.. hehehe..i thot the original had BME280 support but dunno if it ever worked or not.. this is first time messing with that unit.. You asked for it! Please look for V 0.0.33 in the Beta-Store Quote Link to comment
TriLife Posted December 25, 2023 Share Posted December 25, 2023 (edited) 8 minutes ago, TriLife said: You asked for it! Please look for V 0.0.33 in the Beta-Store The original does have BME Support, but not if you have multiple sensors on the same tasmota topic I also haven't tested the original, so if what I sent you doesn't work, we'll have to wait for me to order a BME280. Or you need to configure a Wemos with ONLY a BME280 on it (no other sensors, switches etc) Edited December 25, 2023 by TriLife Quote Link to comment
EWhite Posted December 25, 2023 Author Share Posted December 25, 2023 39 minutes ago, TriLife said: The original does have BME Support, but not if you have multiple sensors on the same tasmota topic I also haven't tested the original, so if what I sent you doesn't work, we'll have to wait for me to order a BME280. Or you need to configure a Wemos with ONLY a BME280 on it (no other sensors, switches etc) i could do that.. i have like 20 of them .. hehe Quote Link to comment
EWhite Posted December 25, 2023 Author Share Posted December 25, 2023 DUDE!!! it works now.. awesome job! Quote Link to comment
EWhite Posted December 25, 2023 Author Share Posted December 25, 2023 Merry Christmas to you and your family! 1 Quote Link to comment
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.