vbsafire1 Posted March 13, 2012 Share Posted March 13, 2012 I am very very new to the isy99i coming from Smartlinc. I am trying to program a very simple action. I want my family room lamp to come on every morning at 6:45 am and go off at 7:35am. I have read everything and I just can't quite grasp the terminology. I don't work with computers but I figured I could at least progrom something as simple as a light coming on and going off at a certain time. I am very fustrated and feeling quite stupid that I can't get this right. Is there anyone out there who can put it in simple or I should say simpler terms for me to understand/ Thanks in advance. Link to comment
oberkc Posted March 13, 2012 Share Posted March 13, 2012 I don't know whether this will help with the broader question of helping understand the terminology, but try: If Time is from 0645am To 0735am Then Set family room light on Else Set family room light off Code verbage is approximate, but I hope this communicates the program logic. Link to comment
vbsafire1 Posted March 13, 2012 Author Share Posted March 13, 2012 Thanks I'll give it a try Link to comment
vbsafire1 Posted March 13, 2012 Author Share Posted March 13, 2012 Another dumb question. How do you type what you want it to say? Link to comment
vbsafire1 Posted March 13, 2012 Author Share Posted March 13, 2012 Do you need to set the program to run or will it run automatically? Link to comment
oberkc Posted March 13, 2012 Share Posted March 13, 2012 One does not actually type the commands...they are created for you when you create a new program and use the choices and options provided. No, you need not set it to run. Have you checked out the user manual? The wiki? Link to comment
vbsafire1 Posted March 13, 2012 Author Share Posted March 13, 2012 Thanks! That worked. I'm slowly starting to understand the terminology. Is there a way to control the ramp rate in the program? Link to comment
ScottAvery Posted March 13, 2012 Share Posted March 13, 2012 Is the "else Off" logic required? I was having a problem where my switch would immediately turn off after being manually turned on. Removing the else from the timer program for that switch eliminated the phantom shut down. Link to comment
LeeG Posted March 13, 2012 Share Posted March 13, 2012 vbsafire1 The Ramp Rate cannot be specified with the Insteon Direct device On command. The switch can be defined as a Responder in an ISY Scene. The responder Ramp Rate can be changed with an Adjust Scene Action statement. The Ramp Rate is stored in the responder device link database so it is not a value that should be changed on a whim but setting the Ramp Rate for day operation and a different value at night for example is fine. The next time the Scene is turned On/Off the new Ramp Rate will be in effect. Link to comment
oberkc Posted March 14, 2012 Share Posted March 14, 2012 Is the "else Off" logic required? I was having a problem where my switch would immediately turn off after being manually turned on. Removing the else from the timer program for that switch eliminated the phantom shut down. Yes, it is required in order to turn the light off at 735. It sounds, in your case, that you may have had a program with a condition including the switch status rather than just time. A lot of folks seem to use (overruse, in my mind) the following construct: If Time is from 0600 To 0900 And status light is not on. <<< this is the extra line I often question Then Set light on Else Set light off A program such as this could cause problems that you describe. Link to comment
ScottAvery Posted March 14, 2012 Share Posted March 14, 2012 Yes, I had indeed done that. Good call! My thinking was that if someone was using the bathroom I wouldn't want to interrupt. As it turns out it isn't relevant since I am using a timer for any On event. I think I will change it though to turn back on after an off, so I can time it from vacancy not occupancy. Link to comment
Recommended Posts
Archived
This topic is now archived and is closed to further replies.