joeria

I had a thread titled as above without the again a few months ago. Below is the last post I made in that thread. Unfortunately after several months of quiet, I'm seeing a handful of devices (same devices each time and same as in the past events) turn on randomly. The devices are not in any common scene except my good night scene which has many more devices. Any thoughts again? So, it has subsided, but my solution/answer is not straightforward. I first tried restoring from IOP the links on all devices that would turn on. That did not solve the issue. I also went through all my programs looking for situations where an "on event" on a device would trigger an "on event" for a scene in which the device was a member as this was a known cause. I either eliminated those situations or put a substantial (several second) delay before executing the scene on. This also did not resolve for me. I note these 2 solutions appear to have helped others. Finally, knowing that the devices that the devices impacted appeared to be older and likely had an "all on" bit in their code, I would take on or two off the network (air gap or unplug) at a time and see if that would stop it. Doing this, I found a couple of old devices that would not air gap or would not take a restore device. I changed these out and have not had an occurrence since. Cost me replacing about 5 devices that appeared to be working fine, but stability is king.

Hi Andy, I think the green panel light takes more into account than checking all nodes. For example if there are nodes that don’t trigger an alert in stay mode (typically motion sensors, but could be others), the light is green even if they are faulted. I doubt that level of detail is provided to the interface. That said I do wish your request could be implemented!

Thanks!!

Not sure when my device (iOS) updated to UD Mobile 1.1.19 but beginning yesterday I noticed the badge count both at the bottom of the app screen and on the icon on phone Home Screen shows the total of all notifications, not just the unread. For me, this is an issue. Have others seen this? thx

@Jimbo.Automates I have basically the same messages in both the network resources and notification customizations. Which is used by the plugin? Looks like it's the notification ID's. Thanks so much, this a great addition! Also, any idea why in the program, the actual name of the customization doesn't appear just the ID? Screenshot attached.

Outstanding! Thanks so much!

Thanks, by using this method it seems not to rely on the node server at all. By changing the network resource, the traditional notify sends only to the group. I was trying to use the functionality of the node server more fully, perhaps using the same network resource messaging and sending to different groups for different conditions.

I think I followed that instruction as well. I've attached 2 screenshots. Once from UD mobile that shows the Groups created and one from IOX that shows a program when the Group box only has the one option. Background - I installed the node server via UD Mobile. I ten went into the PG3X interface and paid for the standard version in case that was the limitation. Also, separte but related, installing the nodes created 2 blank programs - New Notification and New Notification 1. Must these be left there for notifications to function? Thanks again!

Thanks. I've followed this. In the program section, using the Notification Controller / UD Mobile the only choice appearing for Group is REMOVED - Default. How do I get the group(s) I created to be an option in the ISY. Appreciate the help!

Thanks so much. I saw that I can bring the content in. The one thing I'm trying to figure out is how to send to a specific group. I have created the groups on UD mobile, but they don't appear as choices in IOX. Any guidance on this? Thanks again! Joe

Hi, Sorry if I missed seeing a thread on this already if it exists. I currently have been using network resources for several dozen notifications to UD Mobile. I really would like to be able use the Node server group functionality (so my wife doesn't get all the notification I want to see). Is there an easy way to migrate my network resources setup to the notifications module? Thanks for any insight! Joe

Thanks Bob, When was PG3x for Polisy released, surprised my recent update didn't migrate. I've tried updating the node server from the store several times with no luck. Since Weatherbit is now my backup weather server, I can live without it. I won't be able to spend much time over the next couple of weeks with HA stuff, so I'll stay pat and stable and migrate to PG3x in 2 weeks, rather than risking an issue I won't have time to address. THANKS AGAIN! Joe

I resent updated PG3 on Polisy to 3.1.23. I also updated weather bit to 2.06. It no longer will stay connected. Dashboard shows disconnected and below is what the log shows. Any suggestions? Thanks! 2023-07-05 11:06:23,668 MainThread udi_interface INFO polylogger:set_basic_config: set_basic_config: enable=True level=30 2023-07-05 11:06:26,193 MainThread udi_interface INFO __init__:<module>: UDI Python Interface for Polyglot version 3 3.0.59 Starting... 2023-07-05 11:06:26,207 MainThread udi_interface ERROR udi_interface:write: Traceback (most recent call last): 2023-07-05 11:06:26,207 MainThread udi_interface ERROR udi_interface:write: File "/var/polyglot/pg3/ns/000db953c5b4_3/./weatherbit.py", line 9, in <module> 2023-07-05 11:06:26,209 MainThread udi_interface ERROR udi_interface:write: from nodes import Controller 2023-07-05 11:06:26,209 MainThread udi_interface ERROR udi_interface:write: File "/var/polyglot/pg3/ns/000db953c5b4_3/nodes/Controller.py", line 16, in <module> 2023-07-05 11:06:26,211 MainThread udi_interface ERROR udi_interface:write: from nodes import weatherbit_daily 2023-07-05 11:06:26,211 MainThread udi_interface ERROR udi_interface:write: File "/var/polyglot/pg3/ns/000db953c5b4_3/nodes/weatherbit_daily.py", line 8, in <module> 2023-07-05 11:06:26,212 MainThread udi_interface ERROR udi_interface:write: from weather_funcs import weather_codes 2023-07-05 11:06:26,213 MainThread udi_interface ERROR udi_interface:write: ImportError 2023-07-05 11:06:26,214 MainThread udi_interface ERROR udi_interface:write: : 2023-07-05 11:06:26,214 MainThread udi_interface ERROR udi_interface:write: cannot import name 'weather_codes' from 'weather_funcs' (unknown location)

So, it has subsided, but my solution/answer is not straightforward. I first tried restoring from IOP the links on all devices that would turn on. That did not solve the issue. I also went through all my programs looking for situations where an "on event" on a device would trigger an "on event" for a scene in which the device was a member as this was a known cause. I either eliminated those situations or put a substantial (several second) delay before executing the scene on. This also did not resolve for me. I note these 2 solutions appear to have helped others. Finally, knowing that the devices that the devices impacted appeared to be older and likely had an "all on" bit in their code, I would take on or two off the network (air gap or unplug) at a time and see if that would stop it. Doing this, I found a couple of old devices that would not air gap or would not take a restore device. I changed these out and have not had an occurrence since. Cost me replacing about 5 devices that appeared to be working fine, but stability is king.

Thanks @DennisC. I've tried restore device on several of the devices, I'll try on the rest. Had one device that wouldn't fully restore after PLM change. I've subsequently replaced it (after last event) as it was a significantly older device.

I have been trying to troubleshoot a random occurence of an event that turns a number of, but far from all, my insteon devices on. It appears to affect the same devices each time, a handful of dimmers and a few (2 or 3 out of individual buttons on three separate keypads. This seems to happen when no one is cotrolling any connected devices and it doesn't appear to coincide with any program executing. When this occurs the devices that turn on remain listed in ISYas in the prior (off) status and no action is recorded in the logs. So far in terms of troubleshooting: I have no motion sensors in the network I have reviewed and modified any programs so that I do not have a control IF statement executing a scene with the device in the IF statement being updated, or in the couple of cases that exists, I've added 3 seconds delay prior to executing the command. - In any case I can't trace the occurrence to the execution of any program. I've swapped out the PLM in case it was getting flaky - had an event after the swap. Does anyone have any suggestions? Thanks much!

Thanks, I have been running similar programs for quite some time but without the counter. Quick question, once the counter has incremented up, what resets it zero when the condition is corrected?

thanks much @macjeff! All good now.

Upgrade went well for me (on Polisy) but I can't get the local version of admin console to update. Tried accessing with existing start.jnlp, with going through UD site My ISY and using http://xxx.xxx.xx.xx:8080/admin.jnlp and each method fails with mismatch between ISY Firmware (5.5.7) and admin console (5.5.6). I can access AC by choosing cloud. Here's the dialog I get. Any suggestions? Thanks!

Hi, I have been running the TotalConnect poly for quite some time. Thanks, it works well!! I have been tracking a "partial all on" issue in ISY and notice that the log has many entries of "Security / Home - Security Panel / Home - FIRE" with either a status of unknown or OK. Can you give any insight what the genesis of this message going to ISY is? Thanks much! Joe

What bout using UD Mobile on your phone?

thanks for these instructions! Got me back online.

thanks. I also saw on an older thread where something similar was reported that restarting polisy without plm attached resolved the issue. I just tried that - no change.

how do you restart udx?

both ports 8443 and 3000 return not found