Simple program question

[JSchumann]

I have a temp sensor on the output of my furnace.  When water temp goes below 120 I get text notification.  When temp restores I don't get any notification.

 

========================================

Furnace Temp Alert - [iD 000E][Parent 0001]

 

If

        Elk Zone 'Furnace Temp' is Violated

 

Then

        Send Notification to 'AT&T Text' content 'Elk M1 Alert'

        Enable Program 'Furnace Temp Restored'

        Set Elk Speak Word 'Furnace'

        Set Elk Speak Word 'Temperature'

        Set Elk Speak Word 'Low'

 

Else

   - No Actions - (To add one, press 'Action')

==========================================

 

==========================================

Furnace Temp Restored - [iD 000F][Parent 0001][Not Enabled]

 

If

        Elk Zone 'Furnace Temp' is Normal

 

Then

        Send Notification to 'AT&T Text' content 'Elk M1 Alert'

        Disable Program 'Furnace Temp Restored'

 

Else

   - No Actions - (To add one, press 'Action')

=========================================

 

Elk M1 Alert = ${alert.control} ${alert.action}

 

On trip I get 'Furnace temp violated'

 

Or restoration, no text

 

I have to be missing something simple here.......

 

Thanks in advance.

 

John

 

 

 

[larryllix]

 

I have a temp sensor on the output of my furnace.  When water temp goes below 120 I get text notification.  When temp restores I don't get any notification.

 

========================================

Furnace Temp Alert - [iD 000E][Parent 0001]

 

If

        Elk Zone 'Furnace Temp' is Violated

 

Then

        Send Notification to 'AT&T Text' content 'Elk M1 Alert'

        Enable Program 'Furnace Temp Restored'

        Set Elk Speak Word 'Furnace'

        Set Elk Speak Word 'Temperature'

        Set Elk Speak Word 'Low'

 

Else

   - No Actions - (To add one, press 'Action')

==========================================

 

==========================================

Furnace Temp Restored - [iD 000F][Parent 0001][Not Enabled]

 

If

        Elk Zone 'Furnace Temp' is Normal

 

Then

        Send Notification to 'AT&T Text' content 'Elk M1 Alert'

        Disable Program 'Furnace Temp Restored'

 

Else

   - No Actions - (To add one, press 'Action')

=========================================

 

Elk M1 Alert = ${alert.control} ${alert.action}

 

On trip I get 'Furnace temp violated'

 

Or restoration, no text

 

I have to be missing something simple here.......

 

Thanks in advance.

 

John

 

 

Your "Normal" program triggers are disabled.

 

BTW: You could place that code in the Else section of the first program unless there is a hysteresis element by time delay or by temperature difference, effectively giving three states instead of two.

[MWareman]

Sending a network notification is asynchronous. Your program could be completing before its sent. Try adding a wait before the program disables itself to allow the network send to complete.

[JSchumann]

Sending a network notification is asynchronous. Your program could be completing before its sent. Try adding a wait before the program disables itself to allow the network send to complete.

Ahhhh, ok, will try that.

 

Thanks,

John

[JSchumann]

Your "Normal" program triggers are disabled.

 

BTW: You could place that code in the Else section of the first program unless there is a hysteresis element by time delay or by temperature difference, effectively giving three states instead of two.

Probably so (3 states), will try a delay