mango

This is great thank you. Setting up and testing now I have 4314rev2.3 sensors and a v72 serial PLM. The sensors have to be setup manually and report as (2852-222) Leak Sensor v.00 through console. Is this a problem or will I still get full functionality? Wet and dry testing works well, I am presently waiting for a heartbeat and will test for heartbeat missed.

Three reds. Fantastic. Meter time.

Remove the ISY and leave/setup basic scenes on the SL and KPLs

Oberkc I am not the op but thanks for the advice!

Can this not all be done with logic? Do not assign the button directly but have it toggle on and off with programming in between doing the reversing.

I have found using the up and down arrows instead of keying in the values seems to work more often than not.

Now all you need is for your other half to be the recipient so they get the mail from the box for you. Fully automated!

Queuing the writes up in batches is a much nicer way to go about things.

The ISY responds to pings. Does yours?

Yes, DHL will sting you.

This is what I ended up with that seems to work. The end of THEN preps up the scene ready for ELSE for the lights to come back up at slow-ish ramp. Then ELSE returns the scene ramp rate to defaults for regular use. There is probably a more elegant solution no doubt... Den Watch Movie If Control 'X10DenMovieIR' is switched On And Control 'X10DenMovieIR' is not switched Off Or Control 'A2DenKPL / A2DenKPL-A-Movie' is switched On Or Control 'A2DenKPL / A2DenKPL-A-Movie' is not switched Off Then Set Scene 'Den Movie A2DenKPL' On In Scene 'Den Main' Set 'A2DenDoorLL' 3.0 Min (Ramp Rate) In Scene 'Den Main' Set 'A2DenWindowLL' 3.0 Min (Ramp Rate) In Scene 'Den Main' Set 'A2DenDoorLL' 38% (On Level) In Scene 'Den Main' Set 'A2DenWindowLL' 36% (On Level) Wait 5 seconds Set Scene 'Den Main' On Wait 1 minute In Scene 'Den Main' Set 'A2DenDoorLL' 1.0 Min (Ramp Rate) In Scene 'Den Main' Set 'A2DenWindowLL' 1.0 Min (Ramp Rate) In Scene 'Den Main' Set 'A2DenDoorLL' 62% (On Level) In Scene 'Den Main' Set 'A2DenWindowLL' 55% (On Level) Else Set Scene 'Den Main' On Set Scene 'Den Movie A2DenKPL' Off Wait 25 seconds In Scene 'Den Main' Set 'A2DenDoorLL' 4.5 Sec (Ramp Rate) In Scene 'Den Main' Set 'A2DenWindowLL' 4.5 Sec (Ramp Rate) /edited: revised - further ramp modifications

I already had a 10 second wait, now set to 5 to be safe. Great info, thank you.

2456D3 v.37 and v.38 I seem to have found the issue. I factory reset and restored them and now they are responding properly. Thanks for the assist! I spent ages thinking there was some logic I was missing to get the damn things to work for me in what is a very simple program..

Hi Lee and thanks. This is strange as I have tried the set scene on command after the scene changes but nothing happens. I am using a couple of quite old LampLink devices, would this be a factor?

So, I really don't know what I'm doing. I think I asked a poor question to begin with, apologies. May I ask: Adjust Scene, if the scene is already on, and I adjust it, I'd like to be able to initiate the updated scene to the new state. Is this possible?

Thanks jerlands. Kicking myself I realize I haven't fully thought this through. Not only would I like the lights to dim slowly upon movie mode I would need them to ramp back up a little more quickly but not as quick as the default scene ramp rate. X10 C1 ON - enable movie mode (slow ramp down). X10 C1 OFF - disable movie mode, return scene to default settings but ramp up reasonably slowly to help eyes adjust.

Forgive me if this is easy, I am new to adjust scene. How does one go about using adjust scene both light intensity and ramp rate but have the changes happen live? I am away from my home and playing around with this, so I cannot test in person. I've created a watch movie program to adjust aspect lighting in the TV room triggered by a X10 IR event through an IR543 from a programmable remote. This is what I have. The lighting is to dim very slowly. Do I need to run the scene after then and else commands? Perhaps a different programming route required? If Control 'X10DenMovieIR' is switched On Then In Scene 'Den Main' Set 'A2DenDoorLL' 3.0 Min (Ramp Rate) In Scene 'Den Main' Set 'A2DenDoorLL' 38% (On Level) In Scene 'Den Main' Set 'A2DenWindowLL' 3.0 Min (Ramp Rate) In Scene 'Den Main' Set 'A2DenWindowLL' 36% (On Level) Else In Scene 'Den Main' Set 'A2DenDoorLL' 4.5 Sec (Ramp Rate) In Scene 'Den Main' Set 'A2DenDoorLL' 62% (On Level) In Scene 'Den Main' Set 'A2DenWindowLL' 4.5 Sec (Ramp Rate) In Scene 'Den Main' Set 'A2DenWindowLL' 55% (On Level) Thanks for the assist.

An actuator and some hydraulics would be able to fix the problem for you Press either man or woman before you enter.

I could even prep all the buttons up in the software and forward them to the contractor. Ideally I'd like a light burn to make the text similar to the screen printed buttons.

Of course I understand the differing requirements across the board. You could say my point is to confirm what would be an easy commission.

Icons look a little 'too busy' for my personal taste. The keypads stand out much more on the wall. I like them being as unobtrusive as possible. Not discounting the excellent work done of course.

I'd personally be happy with plain old text.

I'd be happy to pay around five bucks US per button. Something to consider. Still quite a bit of work to produce. How much are blanks?

Wow. Amazing. So my question to Marcin would be to consider producing some for clients. I would be interested in about 30 just text in the future.

This is very interesting thank you. What DPI can the laser go down to with how fine a point?