TUhl01

Just want to mention, no wiring required to install the YoLink sensor.

UPDATE - Installed the YoLink Garage Door Sensor 2 today and all functions programmed using the MyQ Server are running with this device. Very impressed with the garage open and close response from the sensor. I already had the YoLink hub for the other devices I am using. $50 for hardware and $10 for the node server can eliminate the MyQ issue. Also, this setup can be used with any overhead door arrangement. Not dependent on the opener.

My MyQ was running great until I did an update reboot a couple of days ago. This is what I am going to try as a go-around. I just ordered a YoLink Smart Garage Door Position Sensor from Amazon. Currently, I am using YoLink products to monitor water leaks and temperature/humidity with IoX programs. It does require a hub. However, the products are not budget busters. My programs are basically looking at the state of the garage door at set times. I believe using the YoLink garage door sensor will allow me to duplicate the MyQ logic for $24.99. I will provide an update when setup is complete to let all know if a viable solution.

All good now. Updated and rebooted again to make sure I was using 5.7.0_5 and MyQ is now back in operation. Thanks for resolving.

Did not work - Deleted MyQ and reinstalled just to see if that would resolve versus just updating.

Just updated PG3x to 3.2.10. Not sure if this is related to the update. MyQ_10-12-2023_10025_PM.zip

What should upgradeStatus be for <modelVersion>5.7.0</modelVersion>? Mine states <upgradeStatus>inactive</upgradeStatus>.

I have had the same problem for a while going offline. It is usually for a short time. Glad to hear it is not only me. I was thinking it may be a problem on the Liftmaster side.

Just updated and still showing 3.1.32.

All good. Changing the priority to Normal did the trick. Have no more issues with Notifications at this time. Thank you.

Implemented Notifications over the weekend and tested with UD Mobile and Pushover. Both are receiving messages with no problems. UD Mobile provides a notification on my iPhone at time of receipt. However, no notification occurs for the Pushover message. Just updated to 3.6.9 and still have the problem. Iox and PG3 are at the current release levels. A message generated from the Pushover website to the iPhone provides a notification.

Fixed - Deleted RING from AC, PG3 Dashboard and reinstalled. Rebooted the EISY. RING test shows SUCCESS now.

Just updated to 1.1.1. Test is resulting in FAILURE. This is the 1st time that I tested for a while. Have not had any active events trigger my programs. This may have been a problem since changing from the Beta version to Production.

I made my purchase from the non-production store last week. I just deleted that version and reinstalled from the production store. All is good except I am back on a trial. How do I bypass purchasing again to make permanent?

Where is "Update" found?

How do I update to 1.1.0? Still showing 1.0.4 Beta

Why is this not showing as an update in UD Mobile?

@GeddyWhat causes losing the connection to the UD Portal? I have the same problem occurring randomly.

I had an offline occur about the same time EDT. Did not save the offline message. I restarted the EISY by doing a power off and on due to not getting an immediate restart. Puzzled why it went offline.

Where is this located - "Discover Devices"?

@Goose66 - I just upgraded to the EISY over the weekend and converted my Polyglots to PG3x. The MyQ is only showing 1 node versus 3. I am using the Polyglot on m Polisy using PG3 with no problems. I tried reinstalling, restarting, powering down the EISY to try to resolve. Firmware is 5.5.9 and all the other Polyglots are functional using PG3x - 3.1.23.

I have been running ZMatter on my Polisy successfully for over a month now. I converted all my devices to Z-Wave months ago to eliminate future Insteon issues. An EISY is being delivered tomorrow along with an USB ZMatter enclosure. I will install the ZMatter board in the enclosure and test with the Polisy before installing on the EISY. From my research, I should just have to perform a backup of the Polisy and a restore from the backup to implement the EISY after powering up. I would appreciate comments from those that have done the same recently. Hopefully this will be a straightforward conversion. Firmware is 5.5.7 and Polyglot PG3 is 3.1.18.

Same here - All devices and routines running very well. I'm very pleased with my Polisy and ZMatter board since replacing the ZooZ Dongle at the beginning of the month.

Updated today from the Admin Console on my PC with no problem. Never used the UD Mobile for updates.

Has anyone successfully been able to get this remote migrated to ZMatter and working? Attachment "B" is the result of the migration. Attachment "C" is the result of the Update and Interview. All the migrated nodes were deleted except the wall controller. This node was the only node highlighted when running the Update and Interview sync option. Attachment "D" is the result of adding the remote to ZMatter where the nodes are completely different than the migrated. Just want to be able to turn a lamp on and off.