CopyRon

My Isy is no longer found here, https://xxxxxxxx.dyndns-at-home.com/ How do I get it back? I can find it at either IP address.

I am now running the Enterprise Evaluation of Windows 8 and Admin Console is working properly.

Thank you, Please call me Ron

Can't log on to Admin Console Windows. Socket error and XML error. Is this because of IE10 or W8?

Installed with no issues!

Chompin' at the bit to try this!!!

Thanks, Michel Looking forward to it!

Any ideas when we'll be seeing support for these?

Although everything seem to go well, I cant not open from this applet. http://www.universal-devices.com/99i/3.1.13 Takes me to UD site

viewtopic.php?f=25&t=6966&start=75 read my same problems reported a while back, about halfway down page 6. Also scroll down to my reply. .

They not only don't report their status, but they do not control the lights they are linked to. However, if I manually push the button inside the motion sensor they will activate their linked device. I removed and reinstalled the MS v1's and they might work for another day or so and then same behavior. ISY would say they were not responding and to check connections. Replacing with V2 solved this.

Maybe just coincidence... but since upgrading to 3.1.9, all of my early (1st version) Motion Sensors have failed. I have replaced them with newer versions, and all appears OK. Actually I have one V1 still working.

What is a 2420M SP? Was linking a new motion sensor and noticed the 2 2420M's.

Best install yet!

Installed perfectly!

Along with Clock/Time not being restored, all of my battery lincs had to restored ( remotelincs, triggerlincs and motion sensors ). Also my EZX10-RF had to be restored. Also all controlincs no longer show status. I will be working on that soon.

The only thing I did between 28.11 and 28.12 was download Home Automation 4 Free. I couldn't find an uninstall for it.

Performed full reset on ISY, had to hold button on for almost 30 seconds. Tried to restore from .12 back up - failed. Restored from .11 back up - all is well again. About says I am at 28.12 I had cleared my certificate during trouble shooting, interestingly, I now have 2 UDi certificates.

Quit again Now I get socket error

Left the ISY unplugged for 5 minutes, everything is suddenly working!

Followed instructions or so I thought, can no longer find my ISY. I have benn trying every version as available and this is the first to fail. I have tried a different PLM and every trick I know to no avail. Help!!!

It seems to me, some time ago I could cross-link an ApplianceLinc to a KeyPadLinc. By doing this, if I turned on the ApplianceLinc from its set button, it would light the corresponding light on the KeyPadLinc. Now, I notice in the ISY, that an ApplianceLinc cannot be configured as a controller. Is there a program I could use that when I turn and ApplianceLinc on from its set button that it would turn on the linked light in its corresponding KPL? In other words I have button eight on my KPL linked to turn on my attic light, which is a fluorescent light plugged into an ApplianceLinc. If I'm already up in the attic, and decide I want to turn on the light, I just press the button on the ApplianceLinc. Them I go downstairs I noticed that the KPL corresponding light is not lit, and therefore I may forget to turn the light off. I just want to know if there's a way, that when that ApplianceLinc is on, I can have a visual confirmation on my KPL.

I had just replaced this KPL with V.36 because thr older one could not do this. After about an hour, the new KPL started responding as I expected.

Is it possible to have an 8 button KPL with button 7 set to toggle off and yet still show the status (in other words, light up) when the linked light is turned on? A program?

I want to thank Michel for his patience and expertise in helping me out with this on line last night. This is an example of how companies should be run, no problems only solutions! I commend you and Universal Devices! Well done!!