frank

Techman, How do I verify the version of the multisensory and the firmware level? I am using the Aeotec Range Extender 6 model ZW117-A01 UI version 5.0.15A Zwave board is the 500 Keep in mind, worked with zero problems with 4.7.3 and 300 Dongle Frank

I have tried inserting a repeater between the devices and the ISY with Zero help. Tried sync'ing devices, repairing and healing. Nothing corrects the problem. Tried moving the repeater to many locations again, no cure. Has anyone else been experiencing this problem? Appears to only show an error when ISY tries to wake up and then put to sleep these devices. Other than these annoying errors, devices appear to function correctly. Frank

Thanks everyone. Some great ideas to ponder. Appreciate the feedback. Sent from my iPhone using Tapatalk

Thanks Ken. Can this controller be mounted outside? If not, can someone recommend a controller than can be mounted outside?

Thanks Bumbetshoot

Thanks Paul. I will take a look at this controller

Would like to get suggestions on best irrigation controller to use with my ISY994iz. Needs to be 8 zones with control via the 994 and cell phone. I also subscribe to Mobilinc. Sent from my iPhone using Tapatalk

I have a program to check for any activation which shows zero. Not sure about battery temp but reasonably sure it is about 80 degrees. I will also look for a 1.5v rechargeable battery. Sent from my iPhone using Tapatalk

Hello ELA, yes, I have a program which monitors the heartbeat and notifies if not sent. Also have a program that notifies me when device is triggered. It is very reliable as tested when I manually activate the switch which is activated by a float switch connected to the external contacts of the sensor. The sensor itself was sealed in a clear nail polish and then placed in a plastic waterproof box. This box is sitting on top of my swimming pool skimmer as the float detects the water level of the pool. I had similar short lifespan of the battery even before the steps taken to waterproof it so I’m convinced the process I used to make it water tight did not make the situation worse. Thanks for your time in corresponding with me on this perplexing issue. ELA, remember, I am using a 1.2v rechargeable NiMH battery which I inserted in place of a 1.5v Alkaline from the factory. The 1.2v appears to operate the device just fine, but I wonder if the .3v is the difference between many months versus weeks of keeping the sensor alive? Sent from my iPhone using Tapatalk

ELA, The only monitor I have is the heartbeat once per day. Other than that transmission, the switch(sensor) has not been activated. The sensor has also been water proofed along with being in a water proof enclosure. Being as it’s outside it is difficult to put any kind of instrumentation on it. Please advise if you have a suggestion on how to monitor this device beyond the heartbeat. Frank Sent from my iPhone using Tapatalk

Thanks kclenden, that may be my only route but would much prefer to find some way to charge the single 1.5v via solar. Sent from my iPhone using Tapatalk

These are most definitely outside here in Florida, which should help. Sent from my iPhone using Tapatalk

Thanks ELA, Great info. Based on info you show here, what would be your guess of size of solar panel (volts and current) needed to charge, say a 1.5 volt rechargeable battery, while also powering the device? I have a project where I can’t run power to the sensor and find I can not keep a battery alive for more than about 6 weeks before it stops sending the heartbeat. I’ve tried different alkaline and NiMh batteries with same results so need to find some way of using solar. Any suggestions greatly appreciated. Frank Sent from my iPhone using Tapatalk

These are NiMH that I am trying to charge from solar at same time it is actively powering the open/close sensor. I have had Very poor battery life with the batteries supplied by Insteon is the reason to go with solar. Do you know what the battery drain of the sensor is normally? Sent from my iPhone using Tapatalk

Looking for ANY ideas on how to charge a 1.2v rechargeable battery in the 2843-222 as I can’t seem to get more than a month off a standard battery. Does anyone know how much Energy is used by the device under normal use in mAh? The less than 1 month was without the device ever opening or closing. Battery was consumed with only the HeartBeat sent each day. If someone knows how much power is used normally, hopefully someone can suggest a solar cell to use or even what voltage and current would also be useful. The solar cell would probably need to supply the working current as well as enough to also charge the battery. I am trying to use a Duracell rechargeable 2650 mAh battery. The 2843-222 is enclosed in a water tight box. Frank Sent from my iPad using Tapatalk

Thank you Sent from my iPhone using Tapatalk

Michel, is there an upgrade path, dollar wise, for users with older modules? Sent from my iPhone using Tapatalk

Thanks Benoit. Great assistance, thank you. Sent from my iPhone using Tapatalk

Thanks a million. Appreciate the response Sent from my iPhone using Tapatalk

Is there a method of printing or sending to a file, ALL details within each program within my network? I know it can be done with a screen shot, but that is a lengthly process. Sent from my iPhone using Tapatalk

Does Alexa announcements support programs? Sent from my iPad using Tapatalk

Is there a way to set a routine to repeat itself such as when the garage door is left open I would get the announcement say every 5 minutes or So? Sent from my iPad using Tapatalk

Auto correct changed isy to island, sorry Sent from my iPad using Tapatalk

Problem solved. Rebooted the island did a discovery. Thanks for the response Sent from my iPad using Tapatalk