Panda88

Hi Has anybody experiencing issues with rain fall in weatherbug/climate information We have had significant rain the last couple of days, but all stations report 0.0" - this naturally screws up the irrigation system. I have my system summarizing in the evening and running in the early morning the following day if needed. If this is common, does the irrigation solution really work? Christian

I am running 3.1.14 Tried to reset the synchrolinc and still the same issue Any ideas? Christian

Lee Thanks I have tried several outlets, and the result is the same. I did manage to get it to show up once, but it never fully worked, so I removed it to try again. It is possible to disable he IR - I am currently not using it. It is likely coming from an LED close by Any other ideas - do you think the unit may have gone bad? Christian

Hi I am having problems getting my new synchrolinc to linc. Here is my log - does anybody have an idea what is going on. Mon 12/19/2011 20:52:17 : [ 18 7E EA 1] Writing High Water Mark at Link 0 Mon 12/19/2011 20:52:17 : [18 7E EA 1 ] Querying engine version Mon 12/19/2011 20:52:17 : [iNST-ACK ] 02 62 18.7E.EA 0F 0D 00 06 (00) Mon 12/19/2011 20:52:18 : [ IR] 02AA Press Mon 12/19/2011 20:52:18 : [iNST-ACK ] 02 62 18.7E.EA 0F 0D 00 06 (00) Mon 12/19/2011 20:52:18 : [iNST-ACK ] 02 62 18.7E.EA 0F 0D 00 06 (00) Mon 12/19/2011 20:52:18 : [ IR] 012A Press Mon 12/19/2011 20:52:18 : [ IR] 0155 Press Mon 12/19/2011 20:52:18 : [18 7E EA 1 ] Failed getting engine version. Reverting to i1 Mon 12/19/2011 20:52:18 : [18 7E EA 1 ] Using engine version i1 Mon 12/19/2011 20:52:18 : [iNST-ACK ] 02 62 18.7E.EA 0F 28 0F 06 SET-MSB(0F) Mon 12/19/2011 20:52:18 : [ IR] 012A Press Mon 12/19/2011 20:52:18 : [iNST-ACK ] 02 62 18.7E.EA 0F 28 0F 06 SET-MSB(0F) Mon 12/19/2011 20:52:18 : [ IR] 00AA Press Mon 12/19/2011 20:52:18 : [iNST-ACK ] 02 62 18.7E.EA 0F 28 0F 06 SET-MSB(0F) Mon 12/19/2011 20:52:19 : [18 7E EA 1 ] ** Not added ** Remove device links failed" Mon 12/19/2011 20:52:19 : ---- All Remaining Device Added ---- Mon 12/19/2011 20:52:19 : [All ] Writing 0 bytes to devices Christian

Lee I do not think it is a power line problem - but I'll try. I can query the device and get the correct state. Does the ISY only update on changes of state or does it query every X min? Thanks Christian

I wonder if it is as simple as status should be control (only execute once key is pressed) I have a similar problem, but probably different. My sensor state does not update - I wonder if is is some of the settings on the IO linc. E.g. I start up the console, and the sensor shows OFF. I run a query, and it updates to the correct state (which is ON). I have a program and it executes as if the state if OFF. Christian

Hi Does anybody have any experience using weatherbug data to control run time (duration) of a pool pump and pool robot cleaner. I have installed timing control using ISY, but I think it must be possible to change the run time of the pump and robot based on the weather (temperature/sun light etc). Do you have any reference on how to determine the run time? I assume there must be a minimum run time, plus some extra time for more sun light and higher temperature. Christian

Lee, I finally got it working I did a factory reset and it started to work - the LED is on when light is off - I have version 5.2 Thanks a lot for your help Christian

Lee, The wiring is correct I'll double check LED status and compare it against the voltage tonight Christian

Lee The motion sensor head works - the light turns on on motion - The sense line is connected to the InLineLinc, Does this not indicate the sensor is working? It also works without using the InLineLinc just wired normally. My understanding is it is the sense line controlling the light - is that not correct? I'll spend some more time to look at the forum to see if I can find any ideas - otherwise - I may just go with a separate sensor. Thanks for your help Christian

Lee Is is the kit sold by smarthome http://www.smarthome.com/2494MSWH/In-Li ... ite/p.aspx Actually, I could not get it to work initially, so I used the original inLinc as a controller elsewhere. I bought an new InLinc as I also got a isy99 in hope it would work now. If this combination is not feasible can you recommend a different sensor type that will with with InLinc Thanks Christian

Lee I checked - the green led is on shortly once the sensor is activated (maybe 1 sec) - then it turns off again - The sensor has different time settings However, I do not see anything showing up in the event log. The event log shows IR event every 5 sec or so, but no activity regarding the sensor The device are off in the main screen Any ideas? Thanks Christian

LeeG In a program - this just means being in the IF statement - correct? I am trying to do it in a program, but no luck - it does not seem to trigger the program once the light goes on Thanks Christian

Hi You may be on to something - there is only a red entry in the device list How do I get the sense controller enable - do I need to remove and insert device again? Thanks Christian

Has anybody made a light sensor driving the in-lineLins w sense work as a controller? I am looking for when the sensor detect something it will turn its own light on as well as other lights. Currently it just turns its own lights on but no even is logged in the isy. As a responder it works fine (meaning at can turn it on from a switch) Does anyone have a sample program Thanks Christian