btreinders

The github page is not found. How do you configure the node server? Thank you!

Another issue I found was scenes in programs not working until you re-saved that program. Not sure if that was because I had to redo all my scenes or not. Just in case others have this issue, just select a line in the program and select update and then save it. Then it starts working.

That was the first thing I checked, it is correct. It seems to happen with variables that get set back to zero after they are set to 1. Like motion detected variables I have set up to have external cameras or Elk motion sensors change them to 1 via REST and then after 5 seconds the ISY changes them back to zero. But ecobee sensors and weather variables form node servers are doing it as well. Some variables, even node servers and variables set via REST don't have the issue though so that is making it difficult to pin down a cause.

@Techman Oh most definitely, I make daily backups. One strange thing I am noticing today is some variable's time changed is 6 hours behind. Like I can even manually change it and the time becomes exactly 6 hrs behind. Only for some though, others are fine. Is this an IoP bug? I have never seen this before. Rebooting did not help either.

@Techman Thank you! Yes, restore works on insteon devices but not node server or z wave. I have a lot of huge scenes and it does take a long time to delete and add back. Spent about 3 hours now and I am almost done.

@Michel KohanimI guess I don't understand what he was telling me then. Can you explain? I have not competed my scene fixing and could still save me a lot time.

I do have one battery insteon motion detector and some other Z wave battery devices. Programs all work except for scenes. If a program runs a scene the scene fails but any other lines in the program are fine. Yes, I have decided to just go through all the scenes and delete and add back all devices. Just adds to the 5 days it has already taken me to convert to IoP, probably take another couple of hours to fix the scenes at a minimum. Thank you!

Yes, I can control the devices and programs are functioning properly. The only thing that does not work until I remove a device and add it back is the scene. Once I add the device back it passes the scene test and work with the scene but no other devices pass or work until they are deleted and added back. It is all the scenes that contain insteon devices and even the other devices won't work if they are in a scene with insteon in it.

Different PLM than original. In the process of switching over the original PLM stopped working. I restored from ISY and then put it on the Polisy. They may have or may not have been working on the ISY, not sure. Do not work from programs either. But they do work from devices, like a keypadlinc still works to turn on and off the correct devices. I have rebooted the Polisy.

All of my scenes are not working after migrating to IoP. If I remove the device from the scene and add it back then that device is good. I have to do this to all the devices in all of the scenes. Any way to speed this up? I have a ton of scenes and devices. Thank you!

I figured it out. The IoP was too busy from a program running standpoint. The Polisy is much faster than the ISY so I had folders with a condition that was the same condition for a lot of programs inside that folder. So when the variable went true in the ISY the folder programs did not see the change as quickly as the folder did so they did not run. It was a safety to ensure the ISY would not lockup if all programs would become enabled all at once. Those folders would stop executing in that case and then a program would go disable all the programs and fix itself and send me a notification. Long story short, too many programs would execute all at once and the IoP would hang. Anyway, I removed the condition from the programs and left it on the folders which should work just as well I hope. Thank you for the help!

I don't see anything in the log that says install or failed

For IoP, the IP address is the same as the Polisy right?

I was changing the IP of the Polisy which changes the ISY on Polisy and the node servers. I had it on one IP and added the ELK node server and set up every thing in the IoP for the ELK (about 100 programs) and then changed the IP to what the ISY standalone had after shutting it down. The ELK node server became unmanaged in PG3 at that point which I did find out is expected and you should not do that. So I changed back to the IP I had installed the ELK with. Still unmanaged. Deleted it out of the IoP, and that got rid of it in PG3 after e reboot I think. Then changed to the IP the original ISY was on again, and tried to install ELK. I get the error in a red pop up, install failed on the ISY just after the green one saying installing the node server.

I installed the ELK node server using a different IP address than I was going to switch to once my ISY was shutdown. I found out that cannot be done so I changed back to the original IP and tried to delete it. It was still unmanaged. I deleted it in the ISY on Polisy. Then I got it removed from PG3. I changed the IP of the Polisy back to what I need it to be but now when I try to install the node server I get an error failed to install to ISY. Any ideas? Thank you.

Thank you!

Any chance you will add the display on keypad and the button pressed on keypad in the future? My program is yellow because I can't change it to anything on the node server that matches. Thank you!

Thank you for the information! I really do appreciate all the hard work of the people in this forum and UD people. I am just frustrated with the amount of work it is taking to convert to Polisy. I don't have any issues with paying for these node servers it was just a surprise to me and was unexpected since they have always been free. I wish there was a way to let people know about the future when they decide to start depending on the node servers. And if the node servers cost money why aren't you charging for PG3 as well? I hope you are getting paid for all of this somehow.

@Jimbo Thanks! Really appreciate it!

I am about to convert to ISY on Polisy and I was unaware of PG2 being deprecated until I saw it on the ISY finder listed that way. My issues with all of this is the lack of an easy way to convert (Z wave, ELK module, network resources, etc...) and then I find out that the new node servers (the reason I bought the Polisy I thought) now will cost more money. I am not saying all the hard work is not worth it and that the developers do not deserve it but I run about 10 node servers and already 2 of them are $30 a piece and one is a yearly subscription. So I paid around $400 for the polisy, another $50 for the z wave stick, and now I might have the potential to spend over $300 more on node servers? There really should be notes when buying a Polisy about the extra expense you might incur if you want to move the ISY to it (which why would you not want to since just the speed of loading programs in the AC alone is awesome), especially when I already bought the ELK module once. I mean what is the incentive to move to PG3 if the node server on PG2 is free but costs $30 on PG3? Will the PG2 node servers still get updates? If we are getting more goodness then it is worth it I guess but right now all of this is very hard. For $300 I would want to press one upgrade button and have it all done automatically. Sorry for the rant but I am in he middle of this conversion and it is really annoying and I haven't even begun to change all the ELK programs which I won't have voice anymore apparently. One good thing I found, since I have Smartthings as the primary Z Wave controller I was able to just shift all the devices to the Polisy and only have to rename them back to what they were. I really do appreciate UD and this forum for all the hard work they do.

Looks like Prowl is only on iPhone and thus will definitely not work with Android Auto. Sure would be nice to get notifications on Android Auto from the ISY without using a slow text message.

I see the exact same with the font size. It is very annoying to me. Sure wish there was a way to make the default another size.

Does it work with Android Auto?

Any idea how to get Pushover notifications to work on Android Auto? I'd make the switch completely if you could. Thanks!

That was fast and it is now working again, and below was Michel's response. I do not know how I deleted the node server from the ISY but you'd think there should be some sort of error if you get in this situation. Michel Kohanim wrote: Thank you Brent. The issue seems to be that you have removed your Rachio node server from ISY but not from PGC. So, it keeps trying to update values (20 per second) and causes a bottleneck. Please remove Rachio from the cloud and you should be OK. With kind regards, ****************************** Michel Kohanim CEO