Jgdavis14 Posted September 22, 2014 Share Posted September 22, 2014 For months I've had a motion detector in the garage that turns on the lights (via togglelinc) and then turns them off after 2 minutes. Several other things involved like time of day and if there is continued motion. It's worked great for months. Recently the lights always seem to be on. I decided to disable the program and just let the motion detector work on it's own. Checking my log in the last 24 hours I've had over 1500 entries with 1400 of them being the sensor doing an on/of routine. I've attached a small screen shot of the last few minutes. Also a shot of the motion detector's settings. Any ideas what the heck I've got going on here? Link to comment
larryllix Posted September 22, 2014 Share Posted September 22, 2014 Racoon in your garage? Your off cycle always lasts about 3 seconds. Are you sure you don't have the darkness sensor being used? Link to comment
stusviews Posted September 22, 2014 Share Posted September 22, 2014 A low battery can cause that. Link to comment
Xathros Posted September 22, 2014 Share Posted September 22, 2014 I can second the low battery as the culprit. Just had one in my basement do exactly the same thing. Low battery node never triggered either. -Xathros Link to comment
Jgdavis14 Posted September 22, 2014 Author Share Posted September 22, 2014 Raccoon not possible. Place closed up and it still reacts the same. Would the darkness sensor cause it to keep checking it's status? And if it's dark, it is supposed to turn on the lights. I do have a program to tell me if the battery is low....but if Zathros said his didn't trigger, that just may be it. I'll try the battery and see what happens. Link to comment
Jgdavis14 Posted September 23, 2014 Author Share Posted September 23, 2014 It looks like it WAS the battery. Replaced it with a new lithium and all is well. It irritates me that the battery sensor never did anything! Link to comment
LeeG Posted September 23, 2014 Share Posted September 23, 2014 What does the Low Batt Program do when Low Batt is indicated? When the ISY is rebooted the Low Batt node is reset to Off. Link to comment
larryllix Posted September 23, 2014 Share Posted September 23, 2014 Perhaps for ALL battery operated devices we need detectors like this? If Control 'Gathering Room / Motion.GathRm' is switched On Or Control 'Gathering Room / Dark.GathRm' is switched On Or Control 'Gathering Room / Dark.GathRm' is switched Off Then Wait 26 hours $MS_Battery_Status = $cGATHERING_ROOM Else - No Actions - (To add one, press 'Action') andb $MS_Battery_Status ${var.2.14} is a State variable so the following programme should event trigger. If $MS_Battery_Status is not 0 Then Wait 5 seconds Send Notification to 'Text Larry' content 'MS Battery Low' Wait 5 seconds Send Notification to 'eMail Larry' content 'MS Battery Low' Wait 12 hours Send Notification to 'Text Larry' content 'MS Battery Low' Wait 5 seconds Send Notification to 'eMail Larry' content 'MS Battery Low' Wait 30 minutes Run Program 'MS Battery Low' (Else Path) Else $MS_Battery_Status = 0 Note $cGATHERING_ROOM is a constant defined by myself and is further used in the notification Alert! MS Battery Low ${sys.date} @${sys.time24} Detected in room ${var.2.14}. 10=RecRm,12=AftBr,13=EveBr 14=Libr,16=Util,19=LLand 20=GathRm,21=MBR,29=MudRm 30=Shop Link to comment
Recommended Posts
Archived
This topic is now archived and is closed to further replies.