Error: Cannot determine device link table address (2466S ToggletLinc)

[iamthesq]

Can someone help me figure out how to get my ToggleLinc added? It's coming up with this error: 

 

Here is the log from the ISY

Wed 12/04/2019 12:28:41 AM : Start Insteon Device Linking Mode
Wed 12/04/2019 12:28:41 AM : [LNK-BGN     ] 02 64 01 00 06 
Wed 12/04/2019 12:28:52 AM : [LNK-STAT    ] 02 53 M(01) gid=00 46.4F.53 021A 41 
Wed 12/04/2019 12:28:52 AM : [46.4F.53 00] Linked device type=02.1A fw=41
Wed 12/04/2019 12:28:52 AM : [46 4F 53 0  ] Added to list of devices to link to ISY
Wed 12/04/2019 12:28:52 AM : [LNK-BGN     ] 02 64 01 00 06 
Wed 12/04/2019 12:28:58 AM : Stop Insteon Device Linking Mode, Final processing to follow
Wed 12/04/2019 12:28:58 AM : [LNK-END     ] 02 65 06 : : Unexpected, ignored (65)
Wed 12/04/2019 12:28:58 AM : [INST-TX-I1  ] 02 62 46 4F 53 0F 0D 00
Wed 12/04/2019 12:28:58 AM : [INST-ACK    ] 02 62 46.4F.53 0F 0D 00 06                 (00)
Wed 12/04/2019 12:29:01 AM : [INST-SRX    ] 02 50 46.4F.53 43.6C.A9 27 0D 02           (02)
Wed 12/04/2019 12:29:01 AM : [Std-Direct Ack] 46.4F.53-->ISY/PLM Group=0, Max Hops=3, Hops Left=1
Wed 12/04/2019 12:29:01 AM : [46 4F 53 0  ] Calibrating engine version
Wed 12/04/2019 12:29:01 AM : [INST-TX-I2CS] 02 62 46 4F 53 1F 2F 00 00 00 00 00 01 00 00 00 00 00 00 00 00 D0
Wed 12/04/2019 12:29:01 AM : [INST-ACK    ] 02 62 46.4F.53 1F 2F 00 00 00 00 00 01 00 00 00 00 00 00 00 00 D0 06        (00)
Wed 12/04/2019 12:29:10 AM : [INST-TX-I2CS] 02 62 46 4F 53 1F 2F 00 00 00 00 00 01 00 00 00 00 00 00 00 00 D0
Wed 12/04/2019 12:29:10 AM : [INST-ACK    ] 02 62 46.4F.53 1F 2F 00 00 00 00 00 01 00 00 00 00 00 00 00 00 D0 06        (00)
Wed 12/04/2019 12:29:18 AM : [INST-TX-I2CS] 02 62 46 4F 53 1F 2F 00 00 00 00 00 01 00 00 00 00 00 00 00 00 D0
Wed 12/04/2019 12:29:18 AM : [INST-ACK    ] 02 62 46.4F.53 1F 2F 00 00 00 00 00 01 00 00 00 00 00 00 00 00 D0 06        (00)
Wed 12/04/2019 12:29:22 AM : [46 4F 53 0  ] Failed to add device, reason 9
Wed 12/04/2019 12:29:23 AM : [All         ] Writing 0 bytes to devices
Wed 12/04/2019 12:29:23 AM : [All         ] Writing 0 bytes to devices
Wed 12/04/2019 12:29:23 AM : [All         ] Writing 0 bytes to devices

 

[Michel Kohanim]

@iamthesq,

In 99% of the cases, this is due to signal/noise. In the other 1%, it's a defective device:

1. Make sure the load is not causing noise
2. Factory reset and link again
3. Move the PLM to a different outlet and one which is not shared with other transformers and power supplies

With kind regards,
Michel