guyhamelin Posted July 7 Share Posted July 7 My new eisy with the serial PLM adapter kit. Installed, upgraded, and restored ISY-994 backup. PLM doesn't show up. PLM Status shows: "0 0 0 v0 / Not Connected". I used the Universal Devices USB to Serial Kit for PLM blue cable to go from the adapter to the PLM and plugged the adapter into the USB on the back of the eisy. I have checked to ensure I have Insteon support selected and I've rebooted the eisy several times. Guy. Link to comment
paulbates Posted July 7 Share Posted July 7 (edited) My initial eisy experience was similar. Did you try the other USB port, restart? Edited July 7 by paulbates Link to comment
guyhamelin Posted July 7 Author Share Posted July 7 Hi, Yes did a lot of try/error with no luck. Link to comment
paulbates Posted July 7 Share Posted July 7 Open a support ticket. I'm sure you'll get going soon. https://www.universal-devices.com/my-tickets/ Link to comment
Techman Posted July 7 Share Posted July 7 @guyhamelin Is the green led on the PLM lit? How old is the PLM? Link to comment
guyhamelin Posted July 7 Author Share Posted July 7 Yes, light is on and the PLM was working on my 994. Everything work good but no communication. Link to comment
Techman Posted July 7 Share Posted July 7 It's possible that the serial to USB cable is defective Link to comment
guyhamelin Posted July 7 Author Share Posted July 7 It's possible but it's a new one from Aartech.ca, Link to comment
Brian H Posted July 7 Share Posted July 7 (edited) You may want to check the pins in the PLM's serial jack. On the off chance one of them is not making connection. As pointed out. A ticket with UDI should get you an answer. Did you power up the PLM first so it was fully booted up when the eisy powered up? Edited July 7 by Brian H Add a question Link to comment
Techman Posted July 7 Share Posted July 7 Under the Configuration tab on the eisy, do you have the box for Insteon support checked? What is your eisy firmware and UI? Have you tried removing power from the PLM and removing and resetting the USB cable at the PLM? 1 Link to comment
guyhamelin Posted July 7 Author Share Posted July 7 1 hour ago, Brian H said: You may want to check the pins in the PLM's serial jack. On the off chance one of them is not making connection. As pointed out. A ticket with UDI should get you an answer. Did you power up the PLM first so it was fully booted up when the eisy powered up? The pins look ok, and I tried to power up the PLM first and no luck, Link to comment
guyhamelin Posted July 7 Author Share Posted July 7 1 hour ago, Techman said: Under the Configuration tab on the eisy, do you have the box for Insteon support checked? What is your eisy firmware and UI? Have you tried removing power from the PLM and removing and resetting the USB cable at the PLM? Yes the box is check, firmware 5.8.4 UI 5.8.4 And I have resettled the PLM : power off, power on with the pin pushed , Link to comment
Techman Posted July 8 Share Posted July 8 At this point you could either try another converter cable or a new USB PLM. I doubt that the issue is with the eisy. Link to comment
Solution guyhamelin Posted July 8 Author Solution Share Posted July 8 Thank you everybody for your help, Michel Kohanim has resolve the communication problem. The brand new cable was not route well inside the RJ45 connector. Wire Orange is suppose to be inside pin 1 and it was in pin 2. 1 1 Link to comment
Brian H Posted July 9 Share Posted July 9 Pin #1 is the serial signal from the PLM to the attached device. Pin #2 is NC. That will definitely cause a no PLM found error. Thank you for keeping us in the loop. Link to comment
BAbdallah Posted August 22 Share Posted August 22 so the DIY cable I can make from an Amazon one is just orange Pin 1, pink pin 7, yellow pin 8 ? Link to comment
Brian H Posted August 22 Share Posted August 22 (edited) Can't comment on the color wires. Yes just 3 wires. If yours is working then you got it correct. Edited August 22 by Brian H Link to comment
Recommended Posts