oskrypuch Posted February 9, 2011 Posted February 9, 2011 When I added a 1900 in ISY (MAS), I got a Main, Heat, Cool and Fan control line. Adding a 1700 (STY) I only get a Main. I can still control the 1700, temps and mode show correctly but the Heat/Cool State is blank on its Main page. Is that normal? I could just remove it and try relinking it to check this, but I have it added now to a lot of programs, so would prefer not to do that unnecessarily. * Orest
Michel Kohanim Posted February 9, 2011 Posted February 9, 2011 Hello Orest, It's normal and it's a function of the dongle and not the thermostat itself: if you have V1 thermostat, then you will only get one node. If you have V2, then you will get two nodes. I think you have a V1 dongle and, if so, you might want to get it upgraded to V2. With kind regards, Michel
oskrypuch Posted February 9, 2011 Author Posted February 9, 2011 OK, pulled the dongle, it says v2.1 on it. On the ISY panel, the version is listed as v.00. Problem with the loading of the device? Did some searching of the forums ... Q. I am thinking that I need to remove that stat from ISY and do a factory reset on the 2441 v2 dongle for good measure, then re-add it. Yes, no? Q. When adding the stat back into ISY, I presume I should use the New INSTEON device dialog, and manually specify a 2441? * Orest
oskrypuch Posted February 9, 2011 Author Posted February 9, 2011 http://wiki.smarthome.com/index.php?tit ... at_Adapter ... * Tap the Set button on Thermostat Adapter once * Press & hold the Set button on Thermostat Adapter for 3 seconds The thermostat display will flash all the LCD characters twice I read this from the WIKI, I did not do the single Set button push referenced above in the linking procedure, just the hold for three seconds to link it. Q. Do you need to give the Set button a short initial press, before holding for 3sec etc. for linking to the ISY? * Orest
oskrypuch Posted February 9, 2011 Author Posted February 9, 2011 Finally ... Q. If I remove the 1700 from ISY, with the 1700 already in a multitude of program statements, do the respective statements disappear, get reassigned a random device, or are they marked as undefined in some way? * Orest
Sub-Routine Posted February 9, 2011 Posted February 9, 2011 OK, pulled the dongle, it says v2.1 on it. On the ISY panel, the version is listed as v.00. Problem with the loading of the device? Did some searching of the forums ... Q. I am thinking that I need to remove that stat from ISY and do a factory reset on the 2441 v2 dongle for good measure, then re-add it. Yes, no? Q. When adding the stat back into ISY, I presume I should use the New INSTEON device dialog, and manually specify a 2441? * Orest Hello Orest, Yes, remove the adapter and perform the reset. Here are the Wiki instructions to link to the ISY: ISY-99i/ISY-26_INSTEON:Linking_a_Thermostat#Linking_a_Thermostat_V2 Q. Do you need to give the Set button a short initial press, before holding for 3sec etc. for linking to the ISY? No. Q. If I remove the 1700 from ISY, with the 1700 already in a multitude of program statements, do the respective statements disappear, get reassigned a random device, or are they marked as undefined in some way? The programs will display Not Specified. You can use Find/Replace then. Rand
oskrypuch Posted February 9, 2011 Author Posted February 9, 2011 All fixed and now working as expected. Thanks! * Orest
Recommended Posts