Timedata
Running on PG3 - An ephemeris node server for Polyglot V3 on Polisy
12 topics in this forum
-
Is there a trial version available for this plug-in? The PG3x store shows a purchase option only.
-
-
- 6 replies
- 886 views
- 3 followers
-
-
I finally got around to installing and migrating to eisy/PG3x from my 994i and polisy (PG2). I had restored PG2 to PG3 on the polisy and attempted to migrate from PG3 to PG3x in eisy but received errors and instructions to install all of the NS's manually, so I did that. I installed them into the same slot numbers as before. I have hundreds of programs with timedata written into them. The PG3x timedata NS in eisy shows as online. However, the programs that have timedata show the following error. I take it that eisy can't "see" the new PG3x NS as being the same. Any advice on how to point the eisy programs to the new timedata server without going through and manually …
-
-
- 11 replies
- 1.5k views
- 3 followers
-
-
I purchased this (didn't realize there was a trial option as it didn't show initially) and can't figure out how to install it. It shows as purchased in the Polyglot 3x server store. The available purchase / install options shows Install Type is ZIP package. I can't find or haven't been sent a link to the Zip package to install the package. Does anyone know how / where to install this nodeserver? I'm hoping this well allow me to easily set a program to run one day a month. It's too bad you can't easily do this within the EISY's time function if / then statements.
-
-
- 2 replies
- 634 views
-
-
The problem is an edge condition where the logic is invoked TWICE (should only be once) if, and only if, the minute being checked is 59 AND another test accompanies it to verify that the hour is not 23. I setup four test to verify this (see attached Test.jpg, Test1.jpg, Test2.jpg, Test3.jpg) two of the tests trigger at two minutes before the hour and they both work properly. The other two tests trigger at one minute before the hour and one of these fails (see attached Test2.jpg) You can see this in the attached Results.jpg file. All variables in the attached Results.jpg file were initialized to zero before running this test. Notice how variable TEST2 was incr…
-
- 17 replies
- 1.5k views
- 1 follower
-
-
What does Timedata give you over just using time and date native in ISY and Eisy?
-
-
- 2 replies
- 961 views
- 1 follower
-
-
Running PG3 3.1.20 on Polisy Running 5.6.0 on IOP When I turn off the nodeserver the online status is not changing to False. Other nodeservers have same issue but most work.
-
- 1 reply
- 845 views
- 1 follower
-
-
in pg3 Node Server list it shows Timedata was updated last night 2/28/23 at 23:14 but when I check its the same version that i have had for a while. Is this due to just a reupload of the same version?
-
-
- 2 replies
- 965 views
- 1 follower
-
-
@glarsen Time data had been running fine but noticed recently some calendar based programs not running. PG3 reported the node server was not running. Spent the evening trying to fix it. Deleted and tried to install but PG3 complained that node server time data file not found. I noticed the firmware date for time data was 1/23/2022 so just within the last week. Is it possible there is a glitch in the new file, or its missing in the store? I am on the latest PG3 and ISY-Polisy. Any help would greatly be appreciated. Tim
-
- 13 replies
- 1.4k views
- 3 followers
-
-
Any chance I could beg you to do a holidays field with US Holidays? Jeff
-
-
- 16 replies
- 2.9k views
- 2 followers
-
-
see screenshot under the Sun part of TimeData
-
-
- 1 reply
- 821 views
- 1 follower
-
-
@glarsen I have Time Data running on both PG2 & PG3. Both are showing sunrise for today at 06:08 am and sunset at 17:57. According to google sunrise today was at 7:11 am and sunset at 7:01 pm. Same differences are shown for tomorrow in Time Data. PoI is showing correct current time and DST is set up for correct location on Configuration page.
-
-
- 11 replies
- 2.4k views
- 2 followers
-
-
I use variables from nodeservers in emails from TimeData and other nodeservers I upgraded from Pg2 to pg3 and none of the variables work now. This was the pg2 version ${sys.node.n014_timedata.GV10} for Season. I noticed its now TimeData so I changed that but still wont work. I am still on node 14 and still need GV10. Ideas?
-
- 2 replies
- 1.5k views
- 1 follower
-