ISY994
Formerly "Questions & Answers for ISY994 Support"
Anything & everything related to ISY994 (hardware & ISY on standalone ISY994 models)
"Formerly Q&A ISY994 Support"
Subforums
-
Z-Wave - Series 300/500 (Managed by the ISY994)
- 12730 posts
13024 topics in this forum
-
I have had my ISY99/IR Pro and Insteon 2412S PLM for several flawless years. I recently upgraded to the 994i/IR Pro and connected to my 2412S PLM and it has worked fine... Until today I was away from our house and went to check the lights using Mobilinc and could not connect to the ISY. Got home and pulled it up on my PC and got the "safe mode" error message, so I unplugged the PLM for 30 seconds to reset (I'm powering the ISY with the PLM). I'm still getting the "safe mode" message when I log on to the ISY. Also, both RX and TX lights on the ISY are on steady for awhile after powering it back up. I can see all my devices in the admin screen, but cannot see any programs …
-
- 23 replies
- 1.8k views
-
-
I'm wondering if I got a bad Thermostat or if this is normal behavior. I just bought the 2441TH and got it installed last night but was really surprised by how bad the viewing angle is on it. The thermostat is mounted considerably below eye level (about mid-chest height) and completely unreadable unless you look directly at it on the same plane (at eye level). Any other angle other than straight on seems unusable. Also, when I push any of the buttons OR anywhere around the plastic bezel around the LCD I notice that the LCD distorts (for lack of a better word), meaning other elements that are not active on the LCD start showing up for a brief second. This seems poorly…
-
- 10 replies
- 1.2k views
-
-
I just updated my Java to 1.8.0_65-b17 and now find that I'm unable to connect to my admin console via https. I receive the following error: What needs to be done to resolve this? Thanks in advance. -Xathros
-
- 2 replies
- 2.3k views
-
-
I have a KPL dimmer that just started going dark (LED back lighting) mostly at night? The unit continues to operate when any of the eight buttons are pressed. Selecting any of the eight keys also lights up that specific LED. Yet the remaining keys are completely black and appears to be set to the lowest setting of off. Currently the only method to restore the back lighting is to air gap the device via the set button. My next step is to hard reset the device and then perform a restore device to see if it correct this odd behavior. I am wondering if anyone else has seen this odd issue and if its a sign of a bad KPL about to give up the ghost? For back ground ref…
-
- 9 replies
- 863 views
-
-
The restore went well, I even got a door sensor working by put it in linking mode (hold set button for several seconds) and then Updating devices in Admin Console. What I can't do is get the lock into linking mode. I do have a Morninglinc, so should I be holding the set button on the Morninglinc. This probably makes sense because I believe ISY is only able to see the Insteon module, not the lock itself. Just don't want to make any mistakes. The door lock is still fully functional so I'm hoping nothing too drastic is required.
-
When I try to update a remotelinc2 that has a scene in common with another remotelinc2, it says they remotelinc cannot be found (becuase I have not put it in learning mode I assume). However when i try to put both remotelinc2s in learning mode they just beep and go back to normal standby mode.
-
- 2 replies
- 796 views
-
-
I've got a bunch of programs and they're all running fine, but I'm trying to add one that should be simple but I can't get it to work. Here's what I'm trying to do: On Mondays I leave the house at 5:30 AM, and on Tuesday, Wednesday, and Thursday I leave at 6:00. If it's dark when I leave I would like the side yard light to be on for 15 minutes. Here's what I've got at the moment: If From Sunset To Sunrise (next day) And On Tue, Wed, Thu Time is 6:00:00AM Or On Mon Time is 5:30:00AM Then In Scene 'Outside / Side Yard' Set 'Outside / Side Yard' 100% (on Level) Wait 15 minutes In Scene 'Outside / Side Y…
-
- 5 replies
- 1.2k views
-
-
I have external venetian blinds, Omega Shades by Draper, which I would like to automate. I've tried the Insteon Open Close controller, but that didn't allow me to have intermediate stops. After reading several forum postings, I purchased Insteon Micro On/Off controller with the hopes that I could make this work. My blinds have two load lines, and are operated manually using a dual momentary switch. They operate on 110V, with amperage range: 1.21 to 1.80. The Open/Close controller has two lines, but the On/Off controller only has one line, although it has two possible connectors to the line. Does anyone have a suggestion on how I can make this work? Do I need…
-
- 11 replies
- 3k views
-
-
Hi All I wanted to get a MS and install it outside to detect anyone one walking up to my front door and also one for the back door. Living in MN it's pretty cold in the winter I was wondering how they performed in the winter. Anyone from a cold weather state have any insight for me Thanks Jeff
-
- 13 replies
- 3.4k views
-
-
So I have a IO Linc on the garage door, a 6 button KPL, and the switch that came with the garage door. What I would like is for button D on the KPL to be lit up when the door is open and off when closed. I would also like the button D to control the door. Right now I have the IO status, IO relay and the KPL Button D in a scene. The IO relay is set to Relay follows Input and Trigger Reversed. Things seem ok when I use the KPL to open the door. It does not like it when I use the real switch. Is there a way to get this to work with a program of some sort? Thanks.
-
- 9 replies
- 1.8k views
-
-
For some reason my keypad linc will make a clicking noise all buttons go dim then goes back to normal. I also notice that if i open my door and the door sensor which is linked to the keypadlinc, the keypadlinc will go dim and make the clicking sound. Ia the keypadlinc going bad?
-
- 4 replies
- 790 views
- 1 follower
-
-
My ISY is using the default ports 80 for HTTP and 443 for SSL. That said, I also have another device WIFI-IR to control all of my AV equipment which also uses port 80. Is this practice ok, or should I change the ISY HTTP port to one which isn't in use? Thank you, Chuck
-
- 2 replies
- 863 views
-
-
Water leak sensors. Must be missing something obvious here. After restart of ISY and two units do not have batteries so the ISY does not know the state of the sensors as can be seen by blank status here however this program runs TRUE and continues to stay true WaterLeakSensor WET - [iD 00D5][Parent 01EC] If Status 'Sensors / WaterLeak Sensors / WaterLeak DownBath-Dry' is Off Or Status 'Sensors / WaterLeak Sensors / WaterLeak Fish-Dry' is Off Or Status 'Sensors / WaterLeak Sensors / WaterLeak FurnaceRoom-Dry' is Off Or Status 'Sensors / WaterLeak Sensors / WaterLeak Kitchen2-Dry' is Off Or Status 'Sensors / WaterL…
-
- 4 replies
- 1.1k views
-
-
I upgraded my ISY994 today and based on the directions there is supposed to be a way to automatically update ISY firmware from within the admin console, however the only means I see is using the manual method via downloading the firmware. Am I missing something? Also, I want to be sure I downloaded and installed the correct firmware. I have an ISY994iZW/IR PRO and there were two options. I chose the first, which I'm now thinking is the wrong one, however I didn't receive any errors. ISY 994i Series including Z-Wave Support ISY 994i ZW, Z, or ZS Series (Z-Wave/Zigbee and/or if you do NOT have a PLM) Thanks, Chuck
-
- 15 replies
- 1.9k views
-
-
I have ISY994iPRO. If I add the Z-wave add-on module, would it be possible to create scene/program which controls both Insteon and Z-Wave devices within a single scene/program? I have never used Z-Wave so I am not sure how the Z-Wave devices appear in the network. Thanks, Arun
-
- 6 replies
- 1.8k views
- 1 follower
-
-
I bought a few 2992-222 to see if I had any communication problems between the two electrical legs. Everywhere I plugged in I got a flashing green status light with the 4 quick hit beacon test. I even got a flashing green status light when I plugged into the same circuit as the PLM The PLM is on a dedicated circuit, alone. I guess this means that I don't have any communication problems between the two electrical legs ? I'll be installing a hardwired phase coupler in the next few days, but based on results so far I don't expect any improvement in reliability. Next I'll start chasing sources of electrical noise by plugging in a few FilterLinc.
-
- 5 replies
- 1.8k views
-
-
I have several Insteon open/close (triggerlinc) sensors on doors and windows. I have some of them programmed through an ISY-994i to flash specific lights when they are opened and send me a text message. My husband is somewhat annoyed with the flashing lights, plus it's not helping me to know exactly which has been opened. The text message is ok for me and helpful when I am away from the house, but I was wondering does anyone know of a way to use something audible in the house for the notification in addition to (or in place of) of the light flashes in the program? Like if I connected some ytpe of bell, chime, or other device to an Insteon I/O linc or to my smartenit E…
-
- 14 replies
- 5.3k views
- 1 follower
-
-
Trying to figure out how many of you use a "wait" time of any duration between actions in one program. For instance, a program that changes the values of several variables and changes the temperature of a thermostat and maybe turns on some lights all in one program. Do you just string the actions together or do you put a wait time of 1-2 seconds between each action or do you put a wait time only between certain types of actions such as after the temperature adjust but not after variable value changes or light changes. Thoughts?
-
- 4 replies
- 941 views
-
-
Can this be done with 1 program or are 2 needed. if time is sunset turn on light I don't see a turn off option. I see a wait x hours but this changes due to sunset etc. If time is midnight turn off light.
-
- 2 replies
- 709 views
-
-
Hi All, I have seen this discussed, but I couldn't find the answer. I want a scene that ramps over the 9 minutes that turns on the house in the morning. So I created a "Wake-up" program, and expected that when I went "On" instead of "Fast On" that it would ramp. Any help would be appreciated, Devon
-
- 6 replies
- 1k views
-
-
I am trying to find a timer program that keeps the bathroom shower fan on for 10 minutes after it is turned off. the program that I found on the forum is not working for me; IF control fan is switched on and status fan is off THEN wait 10 minutes set fan off ELSE (optional) Please let me know if you have seen any other programs that may assist. Thanks Rudy.
-
- 21 replies
- 5.7k views
-
-
Hi, Any who has tried sending SMS to Rogers number? Some details: https = Net::HTTP.new('www.rogerscatalyst.com', 443) https.use_ssl = true request = Net::HTTP::Post.new('/SendSmsService/REST_v0_91/sms') request.basic_auth SystemConfig.configForKey("NAME"), SystemConfig.configForKey("PASSWORD") request.set_form_data({'address'=>'tel:+16479989122xxxxxxx&+1416xxxxxxx', 'message'=>txtMsg}, '&') request.set_content_type 'application/x-www-form-urlencoded' response = https.request(request) How do I convert this into an ISY networking resource? I am stuck on how to do this -> request.set_form_data({'address'=>'tel:+16479989122xxxxxxx…
-
- 11 replies
- 2.9k views
-
-
I am trying to setup a direct link to the camera on my isy, but I am having troulbe passing credentials. I have tried both commands with no success. proceded by http:// user:password@192.168.33.47/WEB/udajax.htm#/conf/cams.jsn&cam=3 or 192.168.33.47/WEB/udajax.htm#/conf/cams.jsn&cam=3&user=usermame&pwd=Password Is anyone aware of the correct syntax, I would not find it on the wiki anywhere. Thank you.
-
- 1 reply
- 730 views
- 1 follower
-
-
I have an issue. My device list (not the tree-view) doesn't show all devices anymore. As you can see from the attached screenshot it shows an error. Can you please advise how I can rectify that? I've tried to backup/restore but it didn't help. So it looks like one file of my configuration is corrupted 60.UND: This is it's content: ue Full: VAR : Task[12] HTTP_1 HTTP-Get pty=19 3644581219 0 -170001 UDQ:Queue Full: SND : Task[1] Alarms AL-DISC-NODES pty=15 3644581220 0 -170001 UDQ: Queue(s) Full, message ignored 3644581228 0 -170001 UDQ:Queue Full: VAR : Task[12] HTTP_1 HTTP-Get pty=19 3644581231 0 -170001 UDQ:Queue Full: SND : Task[1] Alarms AL-DISC-NODES pty…
-
- 2 replies
- 1.2k views
- 1 follower
-
-
I've noticed people talking about the "Set Scene on/off" command in if/then/else programs but I only see the "Adjust Scene" command. How do you find the "Set Scene" command ?