TheA2Z

Installed PG3 3.2.2 from 3.2.1 during eisy upgrade packages. Did my usual reboot after upgrade routine: When time to reboot, hit power button 6 times to shutdown, removed power cord for 30 seconds. Plugged back in. I went in to PG3 and did the reinstall node servers (even though said did not need to above). Everything came back up and is good to go. Thanks UD!

Update: I opened a Ticket as I could not get an Aqara motion or P1 motion to work with eisy. Response was Aqara requires their own hub and is proprietary. UD is not sure if they will ever be able to get those devices to connect. UD recommended the ThirdReality Motion as they have tested with it, so I ordered one from Amazon.

Update: I opened a Ticket as I could not get an Aqara motion or P1 motion to work with eisy. Response was Aqara requires their own hub and is proprietary. UD is not sure if they will ever be able to get those devices to connect. UD recommended the ThirdReality Motion as they have tested with it, so I ordered one from Amazon.

@Jimbo.AutomatesI have been using a ZooZ RGBW controller for a few years now and works great. Got two of them. One for LEDs around TV and one for Kitchen undercabinet lighting. ZOOZ ZEN31 RGBW DIMMER – ZOOZ (getzooz.com) I also have used three of these for about 4 years and work great. I have them in my crawlspace with a separate power supply controlling leds on my stairs. Color LED Controller (Z-Wave) - RGB Genie Both have been solid with my isy and now eisy.

Just got a new Aqara Motion P1 model today. It also is not connecting to Eisy. Will open ticket.

Thanks @Michel Kohanim Im sending it back to Amazon. Im going to get the newer Aqara P1 motion and will try it. If I cant get it to work, Ill open ticket.

Upgraded to 5.6.4 and tried to pair a Aqara Motion (Not P1). No luck. Anyone get any Aqara device connected to Eisy yet? Wondering if I should get the newer Aqara Motion P1 device instead. But before I buy, checking if anyone got an Aqara zigbee device connected yet?

Installed upgrade and then hit reinstall all node services. Working with Elk and notification servers. (Only two I am using right now)

@landolfiActually did not know that. Thanks. Not sure if Aqara devices are ready for prime time yet with Eisy.

@landolfi I held the reset button on Aqara Motion for 10 sec both ways. Once before I pushed add zigbee device and the second time, I pushed Aqara button after I pressed add zigbee device. Would be good to know if anyone got these Aqara motion (non-p1) or even got the new Aqara P1 motion to pair with Eisy?

Just bought a couple of Aqara Motion Detectors (Not P1 but original model) off Amazon. Not pairing with Eisy 5.6.4 Checked Zigbee support then save. Rebooted Eisy Now have zigbee Drop down menu. Clicked add zigbee device Held button on device for 10 seconds. It flashed a view times but did not connect to Eisy. Has anyone been able to get these to work on Eisy? I saw latest 5.6.4 enables Zigbee Motion devices so thought I would give them a try.

Went from 5.6.3 to 5.6.4. Everything seems to be working fine. Note: I, like @Geddy always after upgrading, power down (6 clicks of power button), then unplug the eisy for about 30s, then plug back in. Had a problem in past where that fixed a problem, so now I just do it. Thanks UD devices team for your dedication to making the product better everyday.

@Jimbo.AutomatesI was. I can select it either in IoX or UD Mobile but the only ones that work are disarm and the two "Armed Next" options. The others flash like Armed Stay but then go back to disarmed

Thanks @Jimbo.Automates. The only Armed Status that will set my Elk with UDmobile or IoX is "Armed next Stay Mode" or "Armed next Away Mode". Is that the only two that allow you to change the actual armed status of the Elk alarm from eisy IoX or UD Mobile?

Tried going into elk node in UD mobile for eisy. Trying to set the alarm in stay or away mode in UD Mobile app. Is it possible? Thanks.

I do it with setting a vacation or Away variable. If I set my Elk alarm away it sets the variable to 1. Then all my away programs look for my away variable if 1. When I disarm my alarm the away variable is set by to 0. You could also use UD Mobile to manual set an away variable. Im not into microphones being in my house. Not that Im saying anything concerning. I just value my privacy. I know some will say what about your phone or your Roku device that is listening. I set all those off for microphone listening. Whether they do so or not is another story. That being said, when I sell my house, I will most likely convert my Eisy controller to whatever the most simple controller there is and add Alexa or whatever else is popular at that time. High probability of whoever is buying house not being a techie.

Checked Port with Portchecker. Its open. As for the Host ip config, @MBell that is my IP of my actual rachio device on my network. I thought this was my IP and that the Rachio web will send data via webhooks to it and the port?

Need some help on this one. Installed from PG3 store. In config, I put: Poll short left at 5 Poll Long left at 60 API key from Rachio site. My DDNS address port left as 3001 Left Node additional Interval blank In my Ubiquiti edgerouter: Port Forwarding Page Original Port: 3001 Protocol: Tried all three, UDP, and TCP. Which one? Forward to address: IP of Eisy/ PG3. It is the same for both. Forward to port: Tried 3001. Tried PG3 port. Is it the port number I put in Rachio config or Port number of PG3? With all that, I did not reboot PG3/ Eisy. Wanted to validate config first here.

Eisy is the Universal Devices replacement for the ISY. I moved to it from my ISY.

Why Polisy vs using Eisy device?

I have some battery Zooz devices but not the door sensors. However, they may work the same. Here is what I did to resolve similar problem. Remove device from Eisy Factory reset the device. If you have ability to update the Firmware, do so. I use a home assistant setup that makes it real easy. Here is where it gets fun. Put eisy in add to zwave mode. Take sensor close to eisy and put in inclusion mode. Every 5 to 6 second wake the sensor again Repeat 6 until the sensor is included. See if that works for you.

Agree Timedata is way to go. I was posting a workaround for you in event it is not fixed or fixed quick enough for you.

I sent right when you did. I see now. Impressive. I may be out of my lane in this, but why couldnt you assign minutes to your variable using below screen shot. Then use counters to calculate. Granted it probably could be done programmatically in ISY/eisy, but much easier using Timedata.

Not knowing exactly what the details are. What about something like this where the program would run every second, minute or hour. In your Then you could put the action.

@AGinsburg01Ah. If you dont mind me asking, what is the use case where you are trying to trigger an if on a minute, hour or second value?