TUhl01

Debug log attached. debug.log

When will iOS 1.1.47 be available? Still at 46.

The plugin is not receiving updates. Deleted and reinstalled. This plugin has been working correctly since installed in April. debug.log

I needed something to do, so I started testing the UD Mobile Geofence function. Very easy to setup and it is doing its thing. Upon exiting the zone, a variable GEO_SW is being set to 0, entering the zone to 1. Program GEO TEST MSG is being used to send a UD Mobil message with the state of the value. So far, very impressed. Will use to turn on my garage lights after sunset at some point. GEO TEST MSG - [ID 0050][Parent 004E] If $GEO_SW is 1 Then Set 'SERVER - NOTIFICATION / Notification Controller / UD Mobile' Send Message Content 42 Notification ID (ID=42) Else Set 'SERVER - NOTIFICATION / Notification Controller / UD Mobile' Send Message Content 42 Notification ID (ID=42)

My Remote Connection Access was set to NO. Reconfigured and all 3 parameters were YES. The Ring Test now shows SUCCESS. However, still not getting a motion event in my program. Also, restarted a few times.

Don't see how this topic is related.

I have restarted, deleted and reinstalled. Just tried a restart again and still have the problem. The "Test Ring" keeps generating Failure versus Success. Totally puzzled. Yesterday I added a 2nd Ring Chime. However, chimes are not included in the server node that could cause this.

I have a few programs that are triggered by a RING device motion action. As of this morning, motion is not being activated in IoX. Submitted a ticket. Has anyone else had this problem?

Only 1 battery requires a charge when low. Always just removed the low battery for recharge while 2nd continues to power device.

Can the 2nd battery life be added for the device?

All Good. Compliments to the UD organization.

The Zen17 will not work with MyQ or other smart openers.

Yes - Only open and close status actions are being used in IoX.

Don't have an answer to that question. Suggest going to the PG3 store to get any information for the node server and the creator.

No problem at all with range - max. about 75 ft. for mine. However, I have seen up to 1000 ft for some of their devices. I believe the devices may be communicating locally with the hub and cloud for the app. The ease of adding devices is impressing. Have not had any issues with any of the devices since installing. All the devices are being used to control scenes in IoX.

Just want to mention, no wiring required to install the YoLink sensor.

UPDATE - Installed the YoLink Garage Door Sensor 2 today and all functions programmed using the MyQ Server are running with this device. Very impressed with the garage open and close response from the sensor. I already had the YoLink hub for the other devices I am using. $50 for hardware and $10 for the node server can eliminate the MyQ issue. Also, this setup can be used with any overhead door arrangement. Not dependent on the opener.

My MyQ was running great until I did an update reboot a couple of days ago. This is what I am going to try as a go-around. I just ordered a YoLink Smart Garage Door Position Sensor from Amazon. Currently, I am using YoLink products to monitor water leaks and temperature/humidity with IoX programs. It does require a hub. However, the products are not budget busters. My programs are basically looking at the state of the garage door at set times. I believe using the YoLink garage door sensor will allow me to duplicate the MyQ logic for $24.99. I will provide an update when setup is complete to let all know if a viable solution.

All good now. Updated and rebooted again to make sure I was using 5.7.0_5 and MyQ is now back in operation. Thanks for resolving.

Did not work - Deleted MyQ and reinstalled just to see if that would resolve versus just updating.

Just updated PG3x to 3.2.10. Not sure if this is related to the update. MyQ_10-12-2023_10025_PM.zip

What should upgradeStatus be for <modelVersion>5.7.0</modelVersion>? Mine states <upgradeStatus>inactive</upgradeStatus>.

I have had the same problem for a while going offline. It is usually for a short time. Glad to hear it is not only me. I was thinking it may be a problem on the Liftmaster side.

Just updated and still showing 3.1.32.

All good. Changing the priority to Normal did the trick. Have no more issues with Notifications at this time. Thank you.