BVincent

@mango are you able to use bluetooth for auto unlock also are you able to see in ISY the different users to create programs based on which user unlocks the door?

@JTsao here is what my yale locks show

@JTsao I’ll look at mine today night to see what it shows. I really like the way that lock presents itself but need to be able to differentiate between users.

@JTsao thank you for that information. My Yale lock shows multiple nodes including ability to add user codes and an access control node that shows what user did an action. If I understand you correctly your only shows locked unlocked and no other node types right?

@JTsao With your Polisy, can the this lock recognize different user codes entered? Currently my system is set up so that when certain codes are used to unlock the door it arms or disarms the system but when other codes are used the system does not arm or disarm. This is done so that if I leave for the day and others are at home the system does not arm itself with other in the house since going into the basement would trigger the alarm from a motion sensor.

I understand that, however I hadn't considered this feature until after researching the locks people on here suggested.

Do any of those have auto unlock feature so when approaching your door your smartphone with bt sends a signal to unlock it he door?

Looking to replace my 11 year old Yale Zwave locks. What is everyone using for smart locks? Zwave or wi-fi that integrates with Polisy? update: looking for lock options that allow me to create programs based on the user code entered into the door lock. My old Yale locks do this. thank you.

This can be deleted. Issue I found was the Insteon Support Check Box no checked after migration. I have tried over and over again to migrate from my 700 Zwave usb to the new ZMatter board on my Polisy. Every time I attempt the migration it contiuously goes into the do not make changes, turn devices on or off, progress and after it hits 100% it starts over. I have attempted a reboot in the configuration tab, I have attempted the restart in the configuration tab, I have attempted unplug and re-plug the Polisy with the same outcome. Then I restored back to a working version and attempted to delete all of my ZWave devices and once that was done and working, I attempted to do the migration but the button to just start using the ZMatter board and not migrate ZWave devices. That had the same outcome. Anyone have this happen and know how to get around it? I am fine with deleting my ZWave devices and rebuilding that stuff, however I can't get to a working setup where the progress bar goes away after moving to the ZMatter board.

@dbwarner5 I read your posts and every other post I can find. The system kept updating, hits 100% and starts over. I attempted to do a reboot, same outcome. I then attempted a reboot, same outcome. I then attempted to delete all of the ZWave devices and skip the migration part and still same outcome. Next I restored, 5th or 6th time, had to re-add all my zwave devices with the USB dongle plugged back in and I am back to normal. I have to 5.5.2 firmware and did unplug the USB dongle as the migration says to do. Any thoughts on what next?

@dbwarner5 I have gone the the process and back several times. Once it get to the progress bar of the migration, it gets to 100% and starts over again continues to do that over and over. Is that normal? How long should it take for the migration. I only have 2 locks, 2 switches, and 1 repeater on my build.

@bpwwer i attempted a couple times to update all packages and no luck. Version is still the same and that Node server still won’t connect.

@Michel Kohanim I think the issue is that my front end version of V3 is a tester version and I need to get it to go back to the previous non tester version. Not sure how it ended up on my Polisy unless I accidentally clicked on use beta version at some point.

@simplextech @bpwwer Any status on this? I am still not able to use the ST_Nuheat node_server that I paid $50.00 for and I just did a Polyglot update and still have frontend version 3.1.2

And as far as you know the ST-Heat will not work in the 3.1.2 version.

Any idea how to go back to an earlier version that is not the test version of the system?

I’m not a programmer so I have no idea about this. It does work fine on V2 when I install it on that platform. yes I did delete completely from v2 prior to installing under v3

pg3_8-16-2022_73058_PM.zip

Yes

I have no idea how it ended up on there. How do I revert it back to what it should be?

I am not able to backup my ISY, when it gets to 30% I get the error, Could Not Retrieve File ./FILES/CONF/frontend.pwd I am having some Polyglot issues and was going to reset the system to factory setting but wanted the backup first.

Version 3.1.2 Status: Connected Frontend Version: 3.1.2 ISY Version: 5.4.4 Uptime: 3 Hour(s) 25 Minute(s) 11 Second(s) (c) 2022 UDI Running on Polisy It gave the progress bar after install, just did it again, and now I am leaving it sit to see if it comes up or not.

@simplextech @JimboAutomates I have uninstalled and reinstalled many times, it works with v2 just not v3. I have also tried different node numbers.

pg3-current.log

It does not. I use firefox and there are no new files in the download folder until I downloaded the ecobee package and it is in my download folder