dbwarner5

I think I did, but honestly, I dont remember! But sounds like its an Elk issue. The elk voice has some other oddities as well, where it "accumulates" voice commands during "no speak" time rules, and then when the first voice talks, it dumps out the accumulated voices first.

@Jimbothanks for adding voice to the elk NS! In testing I found the following to work properly: Then Set 'ELK Controller' Speak Word [500ms_Silence] Set 'ELK Controller' Speak Word [500ms_Silence] Set 'ELK Controller' Speak Word [800hz_Tone] Set 'ELK Controller' Speak Word Front Set 'ELK Controller' Speak Word Door (I use the silent command and beep to "wake up" the paging system.) However, when I used the following set up, the page came across as "Front Door is Open". The status should not have been included, and the door was actually shut. Then Set 'ELK Controller' Speak Word [500ms_Silence] Set 'ELK Controller' Speak Word [500ms_Silence] Set 'ELK Controller' Speak Word [800hz_Tone] Set 'ELK Controller' Speak Phrase Front Door Not a big problem, as I can use words vs phrases, but may need to check some of the others.

@jimbo. YEAH!!! Thanks

@peterathans Am not 100% sure what you are asking, but here is a screen shot of my Admin console / Configuration / system / Network Settings, as well as my mobilinc settings. All is working as expected. Once you change your mobilinc settings be sure to click on Tap to Sync with ISY

Thanks. I actually followed the earlier directions: upgraded PG2 then through sudo, restarted polisy which restarted IoP (ISY on polisy), PG2 and PG3. All worked after startup! now running 3.040 version on PG3 thanks! ***UPDATE: Query all ran fine last night!!

I think its this post? directions: update PG2, then restart PG3 via sudo commands?

Jim what is the best way to upgrade it?

It appears mine has just started working again as well. IOS 15.3, mobilinc. I did not do anything to the variable since before when it was working and then through the time period where it quit working.

PG3 is still being perfected. Am not sure how well the conversion of each of those nodes would go or if they are even available on PG3 yet. Elk on pg3 works very well, but there are some bugs still being worked out. Have you ever seen this: https://konnected.io I installed this device in a second home and it works great. This is a fabulous inexpensive product and upgrade of old alarm systems. Not sure if anyone has looked into a node server for it though. I use SmartThings at the second home.

very long thread here about Insteon

@someguy This actually is already in there under the ISY part. Thanks!

You may want to read through this post, especially the last few items in regards to Zwave.

This is where a device may not end up in the right number, gaps etc, and a find /replace will work.

@asbril yes you can run PG2 PG3 and PGC all at the same time. I am running ISY, PG2 PG3 all on my polisy, and PG cloud comes in just fine as well. You need to make sure they are all pointed correctly to the right IP and port for the ISY. For PG2 its under Settings/ Polyglot Settings / ISY Configuration. For PG3, its under ISY's.

a little hard to see your programs, (next time right click on your pgroam, and select copy to clipboard, and then past) I assume the first one follows the example. For the second one, you need to consider two more things: 1) after each zone runs, you need to turn it off, as you turn on the next one. 2) Do you have a pump or is it city water? I have a pump so I need to consider that as well. Would suggest you do something like this: Set zone 1 on wait 20 minutes set zone 2 on wait 1 second set zone 1 off wait 20 minutes etc etc. This way, there is a slight overlap on your zones and that will reduce any hammer you might get from the water. Another enhancement you may want to consider is use a variable for time for each zone and then a second variable that you can change to adjust the whole watering schedule. This requires slightly different programing , more of a chain of programs, where each zone is its own program and calls the next one in line. Here is an example. In this one, I change the variable SP1percent and for all my sprinkler 1 controller programs / times, they all get adjusted. So for dry spells, I may make it 120, for wet spells rescue to 75. etc Here are two of the programs. I have one for each of my zones. SP1 Lake 1 - [ID 02C4][Parent 02BD] If $I_Sp1_Lake_1 > 0 Then Set 'ELK Controller / Sprkl Lake 1' On Set 'ELK Controller / Sprinkler Pump' On $I_Sp_Counter = $I_Sp1_Lake_1 $I_Sp_Counter *= $I_Sp1_Percent $I_Sp_Counter /= 100 Repeat While $I_Sp_Counter > 0 Wait 1 minute $I_Sp_Counter -= 1 Repeat 1 times Run Program 'SP1 Lake 2' (If) Wait 4 seconds Set 'ELK Controller / Sprkl Lake 1' Off Else Run Program 'SP1 Lake 2' (If) SP1 Lake 2 - [ID 02C6][Parent 02BD] If $I_Sp1_Lake_2 > 0 Then Set 'ELK Controller / Sprkl Lake 2' On $I_Sp_Counter = $I_Sp1_Lake_2 $I_Sp_Counter *= $I_Sp1_Percent $I_Sp_Counter /= 100 Repeat While $I_Sp_Counter > 0 Wait 1 minute $I_Sp_Counter -= 1 Repeat 1 times Run Program 'SP1 Lake 3' (If) Wait 4 seconds Set 'ELK Controller / Sprkl Lake 2' Off Else Run Program 'SP1 Lake 3' (If)

2) not sure what or how that would work but probably 3) Yes. Look at my other post. I messed up in that I deleted my old isy UUID from the portal BEFORE I transferred the Alexa stuff so I had to recreate it all. Luckily I had downloaded a copy of my SPokens. In the Portal, there is a migrate option that will move the Alexa stuff from one UUId to another.

@macjeff Am not sure what you mean by redoing the scenes. I did not have to do anything with my scenes. Only my programs that had elk or zwave in them. But I dont have any zwave devices in scenes. All the Insteon stuff, resources, variables, etc all came over seamlessly. The zwave had some potential short cuts in that if an original zwave device Zwave1 was in node ZW006 and now zwave 1 was in ZW008, and Zwave2 device was in ZW006, I could do a find and replace in the programs: find Zwave 2 and replace with Zwave 1. That worked great for a lot of it. I got the Zoos 700 for ~$28. Works great. No problems with it at all. Plugs into the back of the polisy.

@macjeff I would consider moving the ISY first. the performance upgrade is significant. For me the hardest two area in moving was losing the Elk module and having to redo programs after adding the Elk NS on PG3, and then having to read all my z-wave devices. My system is also fairly complex, but not nearly as much zwave as you have. Here is a link to a posting I made of my experience. In moving the Nodeservers, there really isn't a great option on how to do this yet. @Jimbo outlines several options in one of his Nodeserver ReadMe. --> Moving from PG2 There are a few ways to move. Backup and Restore The best way to move from PG2 to PG3 is to backup on PG2 and restore on PG3, but the only option is to do all your nodeservers at once. I don't have much information on this method, if you have questions please ask on the PG3 forum. Delete and add If you can't or don't want backup/restore then you can delete the NS on PG2 and install on the same slot on PG3. All node addresses will stay the same so all your programs should work after doing an update and save on each one, or rebooting the ISY, especially any using the Controller node since it's ST value has changed. Add then delete Another option is to install in a new slot then go edit all your programs and scenes that reference the nodes and switch to the new slots. Good luck!

I moved from the Elk Module to the Elk nodeserver on PG3, purchased from @Jimbo. Its fantastic. Conversion though did mean redoing each program. So I did a Copy Folder to Clipboard of My Programs and had a reference for each program to update it. You will lose voice however, for now. Alexa is a possible replacement option for voice. not as neat / smooth, but works well.

@apostolakisl I moved from the Elk Module to the Elk nodeserver on PG3, purchased fro @Jimbo. Its fantastic. Conversion though did mean redoing each program. So I did a Copy Folder to Clipboard of My Programs and had a reference for each program to update it. You will lose voice however, for now. Alexa is a possible replacement option for voice. not as neat / smooth, but works well.

@jimbo Moved my Kasa from pg2 to pg3. No problems. Did a delete on pg2, add on pg3. Key was to reboot ISY after the delete to free up the slot, per your directions. GREAT!! Glad I can throw it your way, again!

@satwar time/data node server is green. simple. works. I do something similar to what you are trying to do and I keep it pretty simple. Am sure it could be optimized, but its readable and easy. I am looking for three options for my sprinkler program #1. 1) 7 days a week, 2) three days a week 3) every other day. Three separate programs, plus some other very simple programs to change a variable to differentiate between which program is true. 1) Sprinkler 1 7 days - [ID 0158][Parent 02BD] If Time is 4:30:00AM And 'Non Alarm / Rain Sensor' Logical Status is Normal And $Sprinkler_1 is 1 And $I_Sp1_Days is 7 Then Run Program 'SP1 Lake 1' (If) 2) Sprinkler 1 3 Days - [ID 02D6][Parent 02BD] If On Mon, Wed, Fri Time is 4:30:00AM And 'Non Alarm / Rain Sensor' Logical Status is Normal And $Sprinkler_1 is 1 And $I_Sp1_Days is 3 Then Run Program 'SP1 Lake 1' (If) 3) Sprinkler 1 Odd Days - [ID 02D7][Parent 02BD] If Time is 4:30:00AM And 'Non Alarm / Rain Sensor' Logical Status is Normal And $Sprinkler_1 is 1 And $I_Sp1_Days is 2 And 'ISY Time Data' Odd or Even Day is ODD Then Run Program 'SP1 Lake 1' (If) Two enabler programs for the whole sprinkler system and controller program 1 to run or not: All Sprinkler - [ID 01BE][Parent 01A5] If - No Conditions - (To add one, press 'Schedule' or 'Condition') Then $All_Sprinkler = 1 $All_Sprinkler Init To $All_Sprinkler Else $All_Sprinkler = 0 $All_Sprinkler Init To $All_Sprinkler Sprinkler 1 - [ID 0044][Parent 01A5] If - No Conditions - (To add one, press 'Schedule' or 'Condition') Then $Sprinkler_1 = 1 $Sprinkler_1 Init To $Sprinkler_1 Else $Sprinkler_1 = 0 $Sprinkler_1 Init To $Sprinkler_1 Using Mobil link under advanced options for these programs, I change these "enabling" programs to be: -Run then: Enable -Run Else: Disable -True: Enabled -False: Disabled. Delete everything else I have three more for each of the different #days / week that sets the last variable in the Then and a 0 in the Else. Running an else of any of these shuts down the sprinkler as well. Now it super easy to change between: -Turn all sprinkler on or off, -Turn sprkinler program 1 on or off -Select the three different Days a week I preset.

@someguy @apostolakisl Check this post out. I tried to capture all I did in my conversion to IoP (isy on polisy).

ok. thanks for the validation. I will open a ticket on this.

Have run into the same issue. The module appears to not be supported. My devices, while they still appear in My Lighting, they are all "dead links". Clicking on them doesn't even bring up anything at all. The screen stays on whatever it was last on. They have become invisible. Furthermore, I am finding that I cant get the ISY to recognize x10 command received. It will send them fine, using the X10 command line, but not receive them. I will wait and see who else comments here, then open a ticket if needed.