Everything posted by pjjameso
-
Considering disabling ISY due to ALL ON bug. Process to remove it??
Interesting topic and luckily have never experienced the all on issue. Question, why buy the Insteon opener kit when this zwave device is available which would be controlled by the ISY? Would the same issue occur if a keypad button is programed to trigger the isy to send a zwave command to open or close? http://www.amazon.com/dp/B00M75TEIU/ref=wl_it_dp_o_pd_nS_ttl?_encoding=UTF8&colid=PBYV64QP7F0S&coliid=I3FHF55RQ18LT4
-
Installing a Generac Generator
Thank you.... Will get the hang of this eventually.
-
Installing a Generac Generator
Thanks for your code above, I have implemented it along with Webcontrol and it is working well. One question on your code above. I get 2 text messages when the generator goes off, believe this is due to your sendmessage code as else statement says to send off text if GeneracIsOn is not equal to 1. The GeneracIsOn has three states, 1, 2, and 0 so when it changes to 2 or 0 i get the off text. Any thoughts on a fix?
-
Installing a Generac Generator
Thanks Lee, your are correct, must have been tired last night! Found the command have the WebControl send a state variable.
-
Installing a Generac Generator
Larry, Finally had some free time to work on this project a bit more. I have been able to get the state variables to change depending upon the TTL input on the WebControl. However for the life of me I cannot get a program to work and send a text message. If I tell it to run the If statement the text comes but when the state changes from 0 to 1 it doesnt trigger. What am I doing wrong? If $WebControl_IP1 is 1 Then Send Notification to 'Me Text' content 'Generator Power On' Else - No Actions - (To add one, press 'Action')
-
Installing a Generac Generator
Jim, Just received the CAI board. What do I need to do on the ISY side to allow variables to be set by the CAI? Is the ISY network module required? From the CAI manual I see the example to set the ISY URL1 192.168.2.222:80:www:mydomain.com, what the heck is the :www.mydomain.com?
-
Installing a Generac Generator
jzsjr, Looks like im going to have to go the relay and CAI route too. The micro sense is just not a reliable device and I suffer the same issue of not turning off when power to sense is removed. I actually pulled wires ito the house from both the utility side and the generator side of the transfer switch such that when utility is on I have 120 on that pair, and when the generator is running I have on the other pair. This will allow be to test if I have power on both the utility and generator side, generator must be in test mode. Havent worked with the CAI nor webset command so any guidance on how to tie to the relay and trigger the ISY would be appreciated.
-
ISY and PLM Communication Confirmation
This is a follow on to this thread http://forum.universal-devices.com/topic/13915-micro-onoff-sense-for-generator-status/. What I am trying to do is send a text message when the status of two 2443-222 micro switches detects power on sense line 1. I have sense power running from the transfer switch such that when utility power is on it triggers the 2443 and a program (see below) sends a text message. Same for the generator side, when it fires up it triggers the second 2443 and a program sends a text message. A third programs looks at the status of the two 2443 and if the utility has power and the generator has power it sends a text message that the generator is in exercise mode. The 2443 and the ISY are on UPS however I noticed some reliability degradation when I plugged the PLM into the UPS negating the power line transmissions. The generator fires up and transfers load within 30 seconds of utility power failure. Of course if it doesnt nothing will get sent which is why I initially tried to place the PLM on the UPS. Suppose I could put a wait statement in the programs. Any suggestions as to program or hardware modifications would be appreciated. Generator Power On If Control 'Power Source / Generator Power' is switched On Then Send Notification to 'Me Text' content 'Generator Power On' Else - No Actions - (To add one, press 'Action') Generator Power Off If Control 'Power Source / Generator Power' is switched Off Then Send Notification to 'Me Text' content 'Generator Power Off' Else - No Actions - (To add one, press 'Action') Generator Exercise If Control 'Power Source / Generator Power' is switched On And Status 'Power Source / Utility Power' is On Then Send Notification to 'Me Text' content 'Generator Exercise Mode' Else - No Actions - (To add one, press 'Action') Utility Power On If Control 'Power Source / Utility Power' is switched On Then Send Notification to 'Me Text' content 'Utility Power On' Else - No Actions - (To add one, press 'Action')
-
ISY and PLM Communication Confirmation
If I have the ISY (network, etc) on an UPS and a micro 2443 (also on UPS) sends a signal that power has been removed from the sense line, will the ISY keep trying to send the message to the PLM until the PLM (not on UPS) responds? Would like to keep the PLM off the UPS so I can continue to use the power line mode.
-
Micro On/Off Sense for Generator Status
Thanks Mike, Thank God I no longer have any X-10 devices.... Ripped them all out a few years ago after wife complaining that the automation (my hobby) never worked consistently, especially the outdoor entry lights..
-
Micro On/Off Sense for Generator Status
Exactly what I hoped to hear... as the PLM is in the office with 4 other dual band devices, (3x outlets, 1 keypad) I should be in good shape to plug the PLM into the UPS. Follow up question for those who have the PLM plugged into a UPS. Do you still use a filterlinc on the power to the UPS?
-
Micro On/Off Sense for Generator Status
e Excellent point, thank you. So how does the rest of the Insteon network communicate? Specifically if the PLM (dual band) is plugged into the UPS which negates the powerline transmission, do other devices (all dual band) when receiving an RF signal only re transmit an RF or do they transmit both RF and powerline. If they transmit both then as long as you have another dual band device close their shouldnt be any reliability degeneration, correct?
-
Micro On/Off Sense for Generator Status
Thanks, thats what I figure, two micros. Yes PLM & ISY work perfect with the generator. Whats even more surprising is that the micro module Line and Neutral are plugged into the UPS and transmits status perfectly (was thinking that wouldnt work). Kept reading how UPS blocks signals and what is even stranger the UPS is on a fliterlinc too. Would be interesting to try the PLM in the UPS as well as then would have complete redundancy.
-
Micro On/Off Sense for Generator Status
Ok, the yellow sense wire turns the device on, the purple turns the device off. All well and good and works when I apply power and I can hear and see the relay is functioning as such. Issue now appears that although the relay switches it doesnt send an insteon command until the power is removed. If I leave the power connected command is not sent and if left longer the unit starts flashing in error mode. This wont work for me as power will always be applied to purple or yellow (but not at the same time). Appears I may need to have two of these units, one for generator supply, another for utility with them setup as latching, single line, act as 3 way. Any other ideas out there?
-
Micro On/Off Sense for Generator Status
Have a standby generator and would like to know via text whether its sending power or if it is coming from the utility. I have been travelling and would like to know the power status (especially since the generator needs oil everyday of run time under load). I have hooked the sense wires, 1 to the utility, 2 to the generator on each side of the transfer switch. For the life of me I cannot figure out how to program this device to execute an if statement. Is there no option in the ISY to 'sense' whether there is power on either sense line and then execute an action? Im sure I must be missing something here... Thanks in advance
-
Trane XL824 Thermostat w ZWave (Nexia Support)
I just installed the Zwave module in the ISY and trying to get it to work with the XL824 too. Not having any luck anyone have any ideas on how to get these two units to communicate?
-
Trane XL824 Thermostat w ZWave (Nexia Support)
Replacing my heat pump system and will be installing a new Tran XL824 thermostat. Reading the brochure it has ZWave capability. Would the ISY with the ZWave module be able to communicate with the thermostat? Looking to have the thermostat switch to Away Mode when the Elk alarm system is armed. Any experience out there with the XL824 or will I be the guinea pig?
-
2474DWH SwitchLinc Dimmer 2-Wire
You are a genius... that fixed the problem. Had a power outage the other night till the backup generator kicked in. Thanks.
-
2474DWH SwitchLinc Dimmer 2-Wire
After about a month the SwitchLinc has stopped responding to ISY commands and show a big red exclamation mark. Tried to query to no avail. Device is close to other dual band devices (3 - 6 ft) including the ISY PLM. Any thoughts as to whats going on besides just a dead device? Here is the event log... Fri 03/14/2014 11:03:55 AM : [iNST-TX-I1 ] 02 62 24 09 F2 0F 19 00 Fri 03/14/2014 11:03:55 AM : [iNST-ACK ] 02 62 24.09.F2 0F 19 00 06 LTSREQ (LIGHT) Fri 03/14/2014 11:04:04 AM : [iNST-TX-I1 ] 02 62 24 09 F2 0F 19 00 Fri 03/14/2014 11:04:04 AM : [iNST-ACK ] 02 62 24.09.F2 0F 19 00 06 LTSREQ (LIGHT) Fri 03/14/2014 11:04:13 AM : [iNST-TX-I1 ] 02 62 24 09 F2 0F 19 00 Fri 03/14/2014 11:04:13 AM : [iNST-ACK ] 02 62 24.09.F2 0F 19 00 06 LTSREQ (LIGHT)
-
Installing a Generac Generator
Looking to do the same install as you with a micro switch to sense when the generator is supplying power. Any further modifications or wish you had done it differently before I embark on this mod? Thanks in advance.
-
Curtain Control with discrete and global keypad buttons
Okay, inserted a filterlinc between the ups and the outlet. Seems to be working will test over the next couple of days with my fingers crossed. Using a mixture of curtain motors, originally had the somfy dr1000 but they are no longer manufactured and one unit bit the dust. Have switched to the NEW Wisetech (not the one on smarthome) rf model hooked up to an ezio relay. Works great at this point. Only downside with the Wisetech is you need to use two relays outputs vs the one for the Somfy. Somfy didnt care if you left the contact closed as would turn off once it reached the end. Wisetech needs to be momentary, hence two NO connections, one for open other for close. But what the heck, you get 4 relays per EZIO.
-
Curtain Control with discrete and global keypad buttons
I dont have any Access Points but have about 40 dual band devices, not including keypads, in the house so would think that would cover the coupling of the phases, correct? The ISY is on a UPS but the PLM is directly into the same outlet as the UPS. Also in the outlet is the battery backup for FiOS. Im not seeming to have any other problems with communication in the house. Guess I could move the ISY from the basement to the main level, would that help? Question is why would the initial press of the On (or Off) keypad be rejected and not transmitted? Shouldnt I have seen a red light as you mentioned earlier if the transmission was not acknowledged correctly? Would inserting a 1 sec wait statement between each scene help? Other thoughts?
-
Curtain Control with discrete and global keypad buttons
Here is the log from when I pressed the On button on Keypad 1 after a successful pressing of the Off button and correctly executing. The press of the On button did not execute the programs. Sat 02/15/2014 12:09:15 PM : [iNST-SRX ] 02 50 2A.15.B9 11.00.01 C7 06 00 (00) Sat 02/15/2014 12:09:15 PM : [std-Group ] 2A.15.B9-->11.00.01, Max Hops=3, Hops Left=1 Sat 02/15/2014 12:09:15 PM : [iNST-INFO ] Previous message ignored. Here is the result after pressing the On button three times to get the execution of the program. And it didnt execute all the scenes, only 3 of the 4. Sat 02/15/2014 12:13:30 PM : [iNST-SRX ] 02 50 2A.15.B9 11.00.01 C7 06 00 (00) Sat 02/15/2014 12:13:30 PM : [std-Group ] 2A.15.B9-->11.00.01, Max Hops=3, Hops Left=1 Sat 02/15/2014 12:13:30 PM : [iNST-INFO ] Previous message ignored. Sat 02/15/2014 12:13:37 PM : [iNST-SRX ] 02 50 2A.15.B9 11.00.01 C7 06 00 (00) Sat 02/15/2014 12:13:37 PM : [std-Group ] 2A.15.B9-->11.00.01, Max Hops=3, Hops Left=1 Sat 02/15/2014 12:13:37 PM : [iNST-INFO ] Previous message ignored. Sat 02/15/2014 12:13:46 PM : [iNST-SRX ] 02 50 2A.15.B9 11.00.01 C7 06 00 (00) Sat 02/15/2014 12:13:46 PM : [std-Group ] 2A.15.B9-->11.00.01, Max Hops=3, Hops Left=1 Sat 02/15/2014 12:13:46 PM : [iNST-INFO ] Previous message ignored. Sat 02/15/2014 12:13:51 PM : [iNST-SRX ] 02 50 2A.15.B9 00.00.01 C7 11 00 LTONRR (00) Sat 02/15/2014 12:13:51 PM : [std-Group ] 2A.15.B9-->Group=1, Max Hops=3, Hops Left=1 Sat 02/15/2014 12:13:51 PM : [ 2A 15 B9 1] DON 0 Sat 02/15/2014 12:13:51 PM : [iNST-SRX ] 02 50 2A.15.B9 11.00.01 C7 06 00 (00) Sat 02/15/2014 12:13:51 PM : [std-Group ] 2A.15.B9-->11.00.01, Max Hops=3, Hops Left=1 Sat 02/15/2014 12:13:51 PM : [iNST-INFO ] Previous message ignored. Sat 02/15/2014 12:13:51 PM : [iNST-TX-I1 ] 02 62 00 00 47 CF 11 00 Sat 02/15/2014 12:13:51 PM : [iNST-TX-I1 ] 02 62 00 00 48 CF 11 00 Sat 02/15/2014 12:13:51 PM : [iNST-TX-I1 ] 02 62 00 00 45 CF 11 00 Sat 02/15/2014 12:13:51 PM : [iNST-TX-I1 ] 02 62 00 00 41 CF 11 00 Sat 02/15/2014 12:13:51 PM : [iNST-ACK ] 02 62 00.00.47 CF 11 00 06 LTONRR (00) Sat 02/15/2014 12:13:52 PM : [iNST-TX-I1 ] 02 62 28 AB F7 0F 45 01 Sat 02/15/2014 12:13:52 PM : [ 2A 15 B9 1] ST 255 Sat 02/15/2014 12:13:52 PM : [ 2A 15 B9 4] ST 255 Sat 02/15/2014 12:13:52 PM : [iNST-ACK ] 02 62 00.00.48 CF 11 00 06 LTONRR (00) Sat 02/15/2014 12:13:52 PM : [ 28 AC 86 1] ST 255 Sat 02/15/2014 12:13:52 PM : [ 2A 15 B9 6] ST 255 Sat 02/15/2014 12:13:52 PM : [ 28 AC 86 2] ST 255 Sat 02/15/2014 12:13:52 PM : [iNST-ACK ] 02 62 00.00.45 CF 11 00 06 LTONRR (00) Sat 02/15/2014 12:13:52 PM : [ 28 AB F7 3] ST 255 Sat 02/15/2014 12:13:52 PM : [ 2A 15 B9 3] ST 255 Sat 02/15/2014 12:13:53 PM : [iNST-ACK ] 02 62 00.00.41 CF 11 00 06 LTONRR (00) Sat 02/15/2014 12:13:53 PM : [ 2A 15 B9 5] ST 255 Sat 02/15/2014 12:13:53 PM : [iNST-ACK ] 02 62 28.AB.F7 0F 45 01 06 IOON (01) Sat 02/15/2014 12:13:54 PM : [iNST-SRX ] 02 50 28.AB.F7 1F.25.29 27 45 06 IOON (06) Sat 02/15/2014 12:13:54 PM : [std-Direct Ack] 28.AB.F7-->ISY/PLM Group=0, Max Hops=3, Hops Left=1 Sat 02/15/2014 12:13:54 PM : [ 28 AB F7 2] ST 255 Sat 02/15/2014 12:13:54 PM : [iNST-SRX ] 02 50 28.AB.F7 1F.25.29 23 45 06 IOON (06) Sat 02/15/2014 12:13:54 PM : [std-Direct Ack] 28.AB.F7-->ISY/PLM Group=0, Max Hops=3, Hops Left=0 Sat 02/15/2014 12:13:54 PM : [iNST-TX-I1 ] 02 62 28 AB F7 0F 46 01 Sat 02/15/2014 12:13:54 PM : [iNST-ACK ] 02 62 28.AB.F7 0F 46 01 06 IOOFF (01) Sat 02/15/2014 12:13:55 PM : [iNST-SRX ] 02 50 28.AB.F7 1F.25.29 27 46 04 IOOFF (04) Sat 02/15/2014 12:13:55 PM : [std-Direct Ack] 28.AB.F7-->ISY/PLM Group=0, Max Hops=3, Hops Left=1 Sat 02/15/2014 12:13:55 PM : [ 28 AB F7 2] ST 0 Sat 02/15/2014 12:13:55 PM : [iNST-SRX ] 02 50 28.AB.F7 1F.25.29 23 46 04 IOOFF (04) Sat 02/15/2014 12:13:55 PM : [std-Direct Ack] 28.AB.F7-->ISY/PLM Group=0, Max Hops=3, Hops Left=0
-
Curtain Control with discrete and global keypad buttons
The programs are not in a folder. You are correct though in that the ISY is not seeing the Keypad 1 button being pressed either on or off on the first try. The local LED come on indicating it was pressed and the green light at the bottom flashes but no action. Guess these are the new 2334-2 v43 KeypadLinc, any idea why the light flashes at the bottom? New feature?
-
Curtain Control with discrete and global keypad buttons
MBR Curtains Close If Control '2nd Floor / Master Bedroom / MBR Curtain Keypad.1' is switched Off Then Set Scene 'MBR Curtain NE' Off Set Scene 'MBR Curtain NW' Off Set Scene 'MBR Curtain S' Off Set Scene 'MBR Curtain E' Off Run Program 'MBR East Curtain Close' (Then Path) Else - No Actions - (To add one, press 'Action') MBR Curtains Open If Control '2nd Floor / Master Bedroom / MBR Curtain Keypad.1' is switched On Then Set Scene 'MBR Curtain NE' On Set Scene 'MBR Curtain NW' On Set Scene 'MBR Curtain S' On Set Scene 'MBR Curtain E' On Run Program 'MBR East Curtain Open' (Then Path) Else - No Actions - (To add one, press 'Action') MBR East Curtain Close If Control '2nd Floor / Master Bedroom / MBR Curtain Keypad.1 / MBR Curtain Keypad.C' is switched Off Then Set '2nd Floor / Master Bedroom / MBR Curtain South R1' On Wait 3 seconds Set '2nd Floor / Master Bedroom / MBR Curtain South R1' Off Else - No Actions - (To add one, press 'Action') MBR East Curtain Open If Control '2nd Floor / Master Bedroom / MBR Curtain Keypad.1 / MBR Curtain Keypad.C' is switched On Then Set '2nd Floor / Master Bedroom / MBR Curtain South R2' On Wait 3 seconds Set '2nd Floor / Master Bedroom / MBR Curtain South R2' Off Else - No Actions - (To add one, press 'Action') Each MBR Curtain Scene has only the Keypad eg A-D and and the corresponding relay R1-2 The MBR Curtain E only has the keypad C in the scene.