diggler

For some reason my keypad linc will make a clicking noise all buttons go dim then goes back to normal. I also notice that if i open my door and the door sensor which is linked to the keypadlinc, the keypadlinc will go dim and make the clicking sound. Ia the keypadlinc going bad?

I have a micro module that controls the fan only and a kpl that controls the fan light. If fan light is on for more than 2min fan turns on, when light is switched off fan will run for additional 15min. Kpl A 5min run time kpl B 15min run time Sent from my SPH-L710 using Tapatalk

I wound up doing a reset on device hold set button and replace battery and seems to be working now. Sent from my SPH-L710 using Tapatalk

found one online and its useless. just weird, both sensors stopped working around same time. just replaced this one first and having issues with it. tomorrow morning ill see if the other one gives me issues.

nothing changed on the network. if i put battery back in and hit set button activate plunger it works and isy sees it, then couple seconds later i get the red flashing led and cant do anything with it.

Battery went dead. Put new battery in and query the device. Heart beat showa but after a few aeconds i get a red flasshing led on the sensor. On the isy dashboard i get this error Sent from my SPH-L710 using Tapatalk

Dont know what changed but it now works lol. Go figure, only issue is a loud click when it turns on. Is that the fan or module? Module is located in switch box.

Yeah wanted to not have a switch for the fan. Wanted it automated to go on when wife puts lights on in bathroom then stay on for 15 minutes after lights r off.

Ill try it this week. Thx

What does not light up?<br/> I take a 110v tester to test for voltage. Nothing lights up on tester but isy is showing on

1. No. 2. No. 3. Led shows current status green for on and red for off.. 4. No sense wires just on and off needed for exhaust fan. 5. Not home right now (have fan hooked up to keypad and works on and off and with timer program for a.b.c. how do you hard reset? Thanks

No issues. Powered up and isy saw it right away

If the fan goes on I can turn it off remotely. Led shows green when on, but if I put a test lead to the L! terminal it does not light up. The module has power and responds to commands, issue is where the fan lead connects to it does not power on.

I have the module installed. I can turn it on/off but the l1 does not power up all the time. It is hooked up to a exhaust fan for a bathroom. Is it a defective unit???????

For some reason I think i am now getting noise. weird, moved plm to different outlet on different breaker and got everything to work. Switched it back to original outlet and no go. Flipped breaker off then on now works. guess I have a weekend project now, sux

I click start and i am getting cannot communicate with devices. Count says 0

Everything was working fine last night. This morning the pool filter went on at its schedualed time. Then after 10am when it was suppose to shut off it didnt. Went to my phone to turn it off and it didnt, the assigned buttion on keypad was not working too. I turned it off manually. Went to check isy and every single device shows a (!) and says not communicating. Found this very odd, tried unplugging and plugging back in but no go, still doesnt communicate. In PLM/Info Status it says connected. Getting a err1. Is it possible the plm went dead?? thx drew

I have a scene Pool filter on keypadlinc "C" is controller to appliance linc have another scene Pool Filter Keypad lighting. Kepyad "C" is the responder and goes on and off when the program scene runs what I wanna do is run the program to turn on and off 3 different times a day 7 days a week. This part works great and the "C" button shows status I also wanna be able to press the "C" button to turn it on or off. I think its configured right

Got that, but will the "C" button be able to control the on and off for the pump?

On a side note, i have a pool filter setup to a appliance linc. If I write the program to read if status 'pool filter' is on or from 10 am to 10:05 pm same day then set 13.84.44.c on 15/0ff 7 (backlight level) will that turn on the "C" button ??????? The "C" button is linked to control the appliancelinc

I deleted program, re created it. for some reason the pc time was a hr off so when i was testing my program I was off on the time lol. IT works now.

I changed the time to a current one to see if it will go on now. With the "B" button on prior to the time the lights dont go on.

what I am looking to do is, lets say when I go out and wont be home before 830. If i push the "B" button before I leave, when I come home after 830 the lights should come on? It didnt work tho, I'll try again. drew

I wanna define "B" button on front door keypadlinc. When button is depressed and lit, time is 8:30 pm turn on dining room and backroom ceiling light. This is how I have it setup If status 13.83.0d.b is 100% and time is 8:30 pm then set backroom ceiling light on set dining room ceiling light on is this correct thx drew

I click on the scene and it works, thanks