LarryS Posted November 4, 2013 Share Posted November 4, 2013 Hello I have an isy99i that stops responding to network and presumably insteon commands after a few minutes, after restart. Based on several other posts is this forum, I have opened up and reseated the SD card. That did no do much, so I replace the PLM with a new 2413S PLM. Still no go. Short of actually replacing the isy99i, what else should I look at? (Side note: For those upgrading to the 2413s PLM you will need a power supply adapter, I found that the same adapter used on the small black DSL verizon modem works perfectly ) Link to comment Share on other sites More sharing options...
LeeG Posted November 4, 2013 Share Posted November 4, 2013 Look for a Program that is looping. Disable all Programs and see if symptom goes away. Link to comment Share on other sites More sharing options...
LarryS Posted November 8, 2013 Author Share Posted November 8, 2013 Thanks Lee for the suggestion, however it did not change anything. I was able to disable all programs but still it locked up over time. In fact I purchased the isy994i and a new PLM, and restored a backup and same thing happened. I can get it to boot for about 5 mins, but any intense interactions cause it to lock up. (Like query all, or load programs.) Kinda stumped here and am at a loss on how to find the issue; now seems to be more software/programming related. Link to comment Share on other sites More sharing options...
LeeG Posted November 8, 2013 Share Posted November 8, 2013 Was a Save Changes done after the Programs were marked Disabled? Link to comment Share on other sites More sharing options...
LarryS Posted November 8, 2013 Author Share Posted November 8, 2013 Was a Save Changes done after the Programs were marked Disabled? I disabled from the summary tab, there is no save needed from there, just apply. Link to comment Share on other sites More sharing options...
LeeG Posted November 8, 2013 Share Posted November 8, 2013 If all the Programs confirmed the action by showing Disabled that would eliminate a loop. Run Tools | Diagnostics | Event Viewer at LEVEL 3. See if perhaps a device is flooding the network with traffic. You have eliminated the ISY hardware and PLM as the cause. Link to comment Share on other sites More sharing options...
LarryS Posted November 8, 2013 Author Share Posted November 8, 2013 I will check that. I did look at events log at level 1, but not 3. Seemed pretty quiet at 1. I have to contact my client to check that out. Keep in mind there is about 80 devices, and 250 programs.....so I expect it to be kinda busy anyway. Link to comment Share on other sites More sharing options...
LeeG Posted November 8, 2013 Share Posted November 8, 2013 Should not be busy at all with all Programs Disabled. Link to comment Share on other sites More sharing options...
LarryS Posted November 10, 2013 Author Share Posted November 10, 2013 Is there a way to restore only the devices configurations, and not programs? Link to comment Share on other sites More sharing options...
LeeG Posted November 10, 2013 Share Posted November 10, 2013 No, not through UI function. I don't think that would be possible. Program references to devices are by an internal ID not by node name. Using the device definitions that do not match Program definitions taken at the same time could lead to incorrect device references by Programs. Link to comment Share on other sites More sharing options...
Michel Kohanim Posted November 12, 2013 Share Posted November 12, 2013 Hi LeeG, thanks SO very much for all the help. Hi LarryS, please send your Tools | Error Log to support@universal-devices.com. With kind regards, Michel Link to comment Share on other sites More sharing options...
davefred99 Posted January 5, 2014 Share Posted January 5, 2014 I know this thread is a little old now but what was the the outcome of this. Did you ever get the problem solve as I am having a very similar problem with my 99i. I swapped PLM's and the problem did not go away. I also restored my isy to no avail . i have ordered a replacement 994 but really am not sure that is my problem either. Link to comment Share on other sites More sharing options...
Recommended Posts
Archived
This topic is now archived and is closed to further replies.