Automate the World Posted February 6, 2016 Share Posted February 6, 2016 Just got from Smarthome and wanted to replace an EZflora that gave up after 5 years of service and when i try to link it say unsupported.... 22333-233 V 1.C 1057 PS. I am on 4.3.26 Link to comment
paulbates Posted February 7, 2016 Share Posted February 7, 2016 Just got from Smarthome and wanted to replace an EZflora that gave up after 5 years of service and when i try to link it say unsupported.... 22333-233 V 1.C 1057 PS. I am on 4.3.26 Did you try New Insteon Device and manually selecting the ezflora? If you scroll down the list of devices, the ezflora is 4.00 Paul Link to comment
Automate the World Posted February 7, 2016 Author Share Posted February 7, 2016 Did you try New Insteon Device and manually selecting the ezflora? If you scroll down the list of devices, the ezflora is 4.00 Paul Thanks for the pointer Paul! Manually selecting EZFlora did add it into the system as such but for some reason only added 5 of the 8 zones. Any idea why that would be? Link to comment
paulbates Posted February 7, 2016 Share Posted February 7, 2016 Wierd. No reason I can think of. Ideas at this point: Close, then re-run the admin console ..or.. Unplug and replug in the ezflora .. if that doesn't work... repeat step 2, delete the ezflora and add it back in again Guessing a bit at this point Paul Link to comment
LeeG Posted February 7, 2016 Share Posted February 7, 2016 Try right click on EZFlora node and select Group Devices. You may have all,eight nodes but they are not listed together without being 'grouped' together. Link to comment
Automate the World Posted February 7, 2016 Author Share Posted February 7, 2016 Wierd. No reason I can think of. Ideas at this point: Close, then re-run the admin console ..or.. Unplug and replug in the ezflora .. if that doesn't work... repeat step 2, delete the ezflora and add it back in again Guessing a bit at this point Paul Thanks again Paul. Gave those steps a try and same result. Have a wonderful weekend. Try right click on EZFlora node and select Group Devices. You may have all,eight nodes but they are not listed together without being 'grouped' together. Thanks Lee, but that didn't make a difference. Link to comment
paulbates Posted February 7, 2016 Share Posted February 7, 2016 One last suggestion, it may be the ezflora itself. Factory reset the ezflora. I don't know the steps, but the manual in the box should have it. Paul Link to comment
Automate the World Posted February 7, 2016 Author Share Posted February 7, 2016 One last suggestion, it may be the ezflora itself. Factory reset the ezflora. I don't know the steps, but the manual in the box should have it. Paul Negative ghost rider. Thanks again. Link to comment
jerlands Posted February 7, 2016 Share Posted February 7, 2016 Thanks for the pointer Paul! Manually selecting EZFlora did add it into the system as such but for some reason only added 5 of the 8 zones. Any idea why that would be? Curious... what does Help > About show for Firmware and UI? Jon... Link to comment
Automate the World Posted February 7, 2016 Author Share Posted February 7, 2016 Curious... what does Help > About show for Firmware and UI? Jon... 4.3.26 for both Link to comment
jerlands Posted February 7, 2016 Share Posted February 7, 2016 After uninstalling and factory reset you might open Event Viewer to level 3 and copy linking events then post back trace. I've developed a habit with new devices to link from the same outlet as my PLM. I have extension cord I've parted the outlet end from and use that for wired devices and a short adapter I use for wall warts. Jon... Link to comment
Automate the World Posted February 10, 2016 Author Share Posted February 10, 2016 After uninstalling and factory reset you might open Event Viewer to level 3 and copy linking events then post back trace. I've developed a habit with new devices to link from the same outlet as my PLM. I have extension cord I've parted the outlet end from and use that for wired devices and a short adapter I use for wall warts. Jon... Finally had a chance to look at the issue again. Removed the EZFlora, rebooted and then added with a level 3 trace; Tue 02/09/2016 04:09:24 PM : Start Insteon Device Linking Mode Tue 02/09/2016 04:09:24 PM : [LNK-BGN ] 02 64 01 00 06 Tue 02/09/2016 04:09:32 PM : [LNK-STAT ] 02 53 M(01) gid=00 38.7C.3B 0400 28 Tue 02/09/2016 04:09:32 PM : [38.7C.3B 00] Linked device type=04.00 fw=28 Tue 02/09/2016 04:09:32 PM : [38 7C 3B 0 ] Added to list of devices to link to ISY Tue 02/09/2016 04:09:32 PM : [LNK-BGN ] 02 64 01 00 06 Tue 02/09/2016 04:09:33 PM : CLI-HAMW: Connecting to api.aerisapi.com Tue 02/09/2016 04:09:34 PM : CLI-HAMW: Successfully Processed HAMW Response Tue 02/09/2016 04:09:34 PM : CLI-HAMW: Connecting to api.aerisapi.com Tue 02/09/2016 04:09:34 PM : CLI-HAMW: Successfully Processed HAMW Response Tue 02/09/2016 04:09:34 PM : CLI-HAMW: Connecting to api.aerisapi.com Tue 02/09/2016 04:09:34 PM : CLI-HAMW: Successfully Processed HAMW Response Tue 02/09/2016 04:09:48 PM : Stop Insteon Device Linking Mode, Final processing to follow Tue 02/09/2016 04:09:48 PM : [LNK-END ] 02 65 06 : : Unexpected, ignored (65) Tue 02/09/2016 04:09:48 PM : [iNST-TX-I1 ] 02 62 38 7C 3B 0F 0D 00 Tue 02/09/2016 04:09:48 PM : [iNST-ACK ] 02 62 38.7C.3B 0F 0D 00 06 (00) Tue 02/09/2016 04:09:49 PM : [iNST-SRX ] 02 50 38.7C.3B 33.5D.61 2F 0D 02 (02) Tue 02/09/2016 04:09:49 PM : [std-Direct Ack] 38.7C.3B-->ISY/PLM Group=0, Max Hops=3, Hops Left=3 Tue 02/09/2016 04:09:49 PM : [38 7C 3B 0 ] Calibrating engine version Tue 02/09/2016 04:09:49 PM : [iNST-TX-I2CS] 02 62 38 7C 3B 1F 2F 00 00 00 00 00 01 00 00 00 00 00 00 00 00 D0 Tue 02/09/2016 04:09:49 PM : [iNST-ACK ] 02 62 38.7C.3B 1F 2F 00 00 00 00 00 01 00 00 00 00 00 00 00 00 D0 06 (00) Tue 02/09/2016 04:09:49 PM : [iNST-SRX ] 02 50 38.7C.3B 33.5D.61 2F 2F 00 (00) Tue 02/09/2016 04:09:49 PM : [std-Direct Ack] 38.7C.3B-->ISY/PLM Group=0, Max Hops=3, Hops Left=3 Tue 02/09/2016 04:09:50 PM : [iNST-ERX ] 02 51 38 7C 3B 33 5D 61 15 2F 00 00 01 1F FF 00 E2 00 33 5D 61 01 00 00 DE Tue 02/09/2016 04:09:50 PM : [Ext-Direct ] 38.7C.3B-->ISY/PLM Group=0, Max Hops=1, Hops Left=1 Tue 02/09/2016 04:09:50 PM : [38 7C 3B 0 ] Using Database Link Table offset 0x1FF8 (reported 0x1FF8) Tue 02/09/2016 04:09:50 PM : [38 7C 3B 1 ] Start : Adding device to ISY Tue 02/09/2016 04:09:50 PM : [38 7C 3B 1 ] Finish : Adding device to ISY was Successful Tue 02/09/2016 04:09:50 PM : [iNST-TX-I1 ] 02 62 38 7C 3B 0F 44 09 Tue 02/09/2016 04:09:50 PM : [iNST-ACK ] 02 62 38.7C.3B 0F 44 09 06 (09) Tue 02/09/2016 04:09:51 PM : [iNST-SRX ] 02 50 38.7C.3B 33.5D.61 2B 44 00 (00) Tue 02/09/2016 04:09:51 PM : [std-Direct Ack] 38.7C.3B-->ISY/PLM Group=0, Max Hops=3, Hops Left=2 Tue 02/09/2016 04:09:51 PM : [38 7C 3B 2 ] Start : Adding device to ISY Tue 02/09/2016 04:09:51 PM : [38 7C 3B 2 ] Finish : Adding device to ISY was Successful Tue 02/09/2016 04:09:51 PM : [iNST-SRX ] 02 50 38.7C.3B 33.5D.61 23 44 00 (00) Tue 02/09/2016 04:09:51 PM : [std-Direct Ack] 38.7C.3B-->ISY/PLM Group=0, Max Hops=3, Hops Left=0 Tue 02/09/2016 04:09:51 PM : [38 7C 3B 3 ] Start : Adding device to ISY Tue 02/09/2016 04:09:51 PM : [38 7C 3B 3 ] Finish : Adding device to ISY was Successful Tue 02/09/2016 04:09:51 PM : [38 7C 3B 4 ] Start : Adding device to ISY Tue 02/09/2016 04:09:51 PM : [38 7C 3B 4 ] Finish : Adding device to ISY was Successful Tue 02/09/2016 04:09:51 PM : [38 7C 3B 5 ] Start : Adding device to ISY Tue 02/09/2016 04:09:51 PM : [38 7C 3B 5 ] Finish : Adding device to ISY was Successful Tue 02/09/2016 04:09:51 PM : [iNST-TX-I1 ] 02 62 38 7C 3B 0F 44 02 Tue 02/09/2016 04:09:51 PM : [iNST-ACK ] 02 62 38.7C.3B 0F 44 02 06 (02) Tue 02/09/2016 04:09:51 PM : [iNST-SRX ] 02 50 38.7C.3B 33.5D.61 2F 44 00 (00) Tue 02/09/2016 04:09:51 PM : [std-Direct Ack] 38.7C.3B-->ISY/PLM Group=0, Max Hops=3, Hops Left=3 Tue 02/09/2016 04:09:51 PM : [38 7C 3B 0 ] Successfully added device Tue 02/09/2016 04:09:52 PM : [D2D EVENT ] Event [38 7C 3B 1] [sT] [0] uom=0 prec=-1 Tue 02/09/2016 04:09:52 PM : [ 38 7C 3B 1] ST 0 Tue 02/09/2016 04:09:52 PM : [iNST-TX-I1 ] 02 62 1D FE E2 0F 14 00 Tue 02/09/2016 04:09:52 PM : [iNST-ACK ] 02 62 1D.FE.E2 0F 14 00 06 LTOFF-F(00) Tue 02/09/2016 04:09:52 PM : [D2D EVENT ] Event [38 7C 3B 2] [sT] [0] uom=0 prec=-1 Tue 02/09/2016 04:09:52 PM : [ 38 7C 3B 2] ST 0 Tue 02/09/2016 04:09:52 PM : [D2D EVENT ] Event [38 7C 3B 1] [sT] [0] uom=0 prec=-1 Tue 02/09/2016 04:09:52 PM : [ 38 7C 3B 1] ST 0 Tue 02/09/2016 04:09:52 PM : [D2D EVENT ] Event [38 7C 3B 3] [sT] [0] uom=0 prec=-1 Tue 02/09/2016 04:09:52 PM : [ 38 7C 3B 3] ST 0 Tue 02/09/2016 04:09:52 PM : [D2D EVENT ] Event [38 7C 3B 4] [sT] [0] uom=0 prec=-1 Tue 02/09/2016 04:09:52 PM : [ 38 7C 3B 4] ST 0 Tue 02/09/2016 04:09:52 PM : [D2D EVENT ] Event [38 7C 3B 5] [sT] [0] uom=0 prec=-1 Tue 02/09/2016 04:09:52 PM : [ 38 7C 3B 5] ST 0 Tue 02/09/2016 04:09:52 PM : [All ] Writing 0 bytes to devices Tue 02/09/2016 04:09:52 PM : [All ] Writing 0 bytes to devices Tue 02/09/2016 04:09:52 PM : [iNST-SRX ] 02 50 1D.FE.E2 33.5D.61 2B 14 00 LTOFF-F(00) Tue 02/09/2016 04:09:52 PM : [std-Direct Ack] 1D.FE.E2-->ISY/PLM Group=0, Max Hops=3, Hops Left=2 Tue 02/09/2016 04:09:52 PM : [D2D EVENT ] Event [1D FE E2 1] [sT] [0] uom=0 prec=-1 Tue 02/09/2016 04:09:52 PM : [ 1D FE E2 1] ST 0 Tue 02/09/2016 04:09:52 PM : [D2D-CMP 0040] STS [1D FE E2 1] ST op=1 Event(val=0 uom=0 prec=-1) is Condition(val=0 uom=0 prec=-1) --> true Tue 02/09/2016 04:09:53 PM : [D2D-CMP 0040] STS [1D FE E2 1] ST op=1 Event(val=0 uom=0 prec=-1) is Condition(val=0 uom=0 prec=-1) --> true Tue 02/09/2016 04:09:53 PM : [D2D-CMP 003C] STS [1D FE E2 1] ST op=6 Event(val=0 uom=0 prec=-1) != Condition(val=0 uom=0 prec=-1) --> false Tue 02/09/2016 04:10:33 PM : CLI-HAMW: Connecting to api.aerisapi.com Tue 02/09/2016 04:10:34 PM : CLI-HAMW: Successfully Processed HAMW Response Tue 02/09/2016 04:10:34 PM : CLI-HAMW: Connecting to api.aerisapi.com Tue 02/09/2016 04:10:34 PM : CLI-HAMW: Successfully Processed HAMW Response Tue 02/09/2016 04:10:34 PM : CLI-HAMW: Connecting to api.aerisapi.com Tue 02/09/2016 04:10:35 PM : CLI-HAMW: Successfully Processed HAMW Response Still only getting 5 stations.... Link to comment
Michel Kohanim Posted February 10, 2016 Share Posted February 10, 2016 Hello Automate The World, Is this a 994i? If so, do you know how many nodes/scenes/folders you have? It might be that you are reaching the 254 limit. With kind regards, Michel Link to comment
Automate the World Posted February 12, 2016 Author Share Posted February 12, 2016 Hello Automate The World, Is this a 994i? If so, do you know how many nodes/scenes/folders you have? It might be that you are reaching the 254 limit. With kind regards, Michel thanks for the reply Michel. Is there a count somewhere or do I have to literally count each one? Link to comment
Michel Kohanim Posted February 14, 2016 Share Posted February 14, 2016 Hello Automate The World, Unfortunately no count anywhere. This said, you can definitely use Tools | Generate Topology for a high level view of where you are. With kind regards, Michel Link to comment
Automate the World Posted February 14, 2016 Author Share Posted February 14, 2016 Hello Automate The World, Unfortunately no count anywhere. This said, you can definitely use Tools | Generate Topology for a high level view of where you are. With kind regards, Michel Hi Michel, Thanks for the tip. Instead I had a few devices that I don't use anymore so I deleted them from the system and then re-added the EZFlora and everything is all good! It would have been nice if as I was linking and there were not enough nodes available that a message would tell me so. On a side note I remember thinking about 4 years ago when I bought this ISY that there is no way I would ever need more than 256 devices/nodes and here we are. Thanks for all the help everyone! Link to comment
Michel Kohanim Posted February 15, 2016 Share Posted February 15, 2016 Hello Automate The World, I am so very sorry that you had to go through this and, yes, we should definitely have some indication of the number of nodes used. With kind regards, Michel Link to comment
Recommended Posts
Archived
This topic is now archived and is closed to further replies.