Jump to content

Do I have, again, a broken PLM ??


Recommended Posts

Hi

 

My ISY is accessed via Home Assistant to only control devices. All was working fine for many months until  this morning.

I initially thought I had an issue with Home assistant, so I fire up the  administrative console, but no luck. ISY cannot talk to any of my devices. I reset the PLM and reprogram it, still the same issue.

My PLM is only 1.5 years old, was already replaced twice in the last 7 years. I thought by having a 2.4 version would  free me of those problem, for at least 3-4 years, but seem not.

Before going forward, I would like to be sure I have a bad PLM, I include below a log output.

When I check for the PLM from Tools -> diagnostics -> PLM status, I only get connected.

The "reprogram" seem to have working fine.

Nothing change on the electrical side.

 

At this point I'm clueless on what I should do next to confirm a bad PLM, which do have a green led "on". Any advise

 

Regards

 

 

5603 L1 / L1_portique_banquette  Error   0.00000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000 Mon 2020/01/13 23:08:
5604 L1 / L1_portique_banquette          Mon 2020/01/13 23:08:37 System  -2  
5605 L1 / L1_Portique_plafond    Error   0.00000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000 Mon 2020/01/13 23:08:
5606 L1 / L1_Portique_plafond            Mon 2020/01/13 23:08:59 System  -2  
5607 Exterieur / L1_Veranda  Error   0.00000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000 Mon 2020/01/13 23:09:21 S
5608 Exterieur / L1_Veranda          Mon 2020/01/13 23:09:21 System  -2  
5609 L1 / L1_SDB Error   0.00000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000 Mon 2020/01/13 23:09:43 System  Log
5610 L1 / L1_SDB         Mon 2020/01/13 23:09:43 System  -2  
5611 L2 / L2_3way_esc_haut   Error   0.00000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000 Mon 2020/01/13 23:10:27 S
5612 L2 / L2_3way_esc_haut           Mon 2020/01/13 23:10:27 System  -2  
5613 L2 / L2_maitre_multi.1  Error   0.00000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000 Mon 2020/01/13 23:10:49 S
5614 L2 / L2_maitre_multi.1          Mon 2020/01/13 23:10:49 System  -2  
5615 L2 / L2_maitre_douche   Error   0.00000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000 Mon 2020/01/13 23:11:11 S
5616 L2 / L2_maitre_douche           Mon 2020/01/13 23:11:11 System  -2  
5617 Thermostat / L1_Thermostat- Main    Error   0.00000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000 Mon 2020/01/1
5618 Thermostat / L1_Thermostat- Main            Mon 2020/01/13 23:11:33 System  -2  
5619 L1 / L1_foyer   Error   0.00000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000 Mon 2020/01/13 23:11:55 System  L
5620 L1 / L1_foyer           Mon 2020/01/13 23:11:55 System  -2  
5621 L1 / L1_3way_esc_bas    Error   0.00000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000 Mon 2020/01/13 23:12:17 S
5622 L1 / L1_3way_esc_bas            Mon 2020/01/13 23:12:17 System  -2  
5623 Get NodeDef ZWave   0   Mon 2020/01/13 23:13:38 System  Log  

Link to comment
Share on other sites

The revision 2.4 PLM. Has the updated Serial Port Daughter Card with better serial signal protection and C7 and C13 are now a capacitor designed for switching power supplies.

You may want to try it in a different location, look for a newly added electronic device maybe causing electrical noise or absorbing the power line signals.

Link to comment
Share on other sites

Well,

 

I was about to move my ISY/PLM to another location but test once again. All is back to normal. I change nothing, I wonder if a good night was the answer. All I could say is for 6 hours it didn't work last night and nothing really change. I did try resetting the PLM and reprogramming it as a fix maybe that was the answer, but i swear, that it didn't work after that. Sorry for this inconvenience.

As usual, thanks for the quick feedback. A good reason to use ISY

Regards

Link to comment
Share on other sites

Archived

This topic is now archived and is closed to further replies.


×
×
  • Create New...