LFMc Posted October 31, 2020 Share Posted October 31, 2020 Hi All, I was hoping to find an easy way to do this, but I have not found it. I need to enter a value into an ISY (v 4.7.5) variable with the Insteon 2441TH set point temp and the current temperature. Also I would like to direct set the thermostat's set point from a variable. I have found no way to put the temps into a variable. I can put the thermostat into a known/fixed set point and then increase or decrease the temp in one degree increments accordingly, but I have found that the thermostat occasionally doesn't respond to the up/down 1 degree command and I have no way of knowing that occurred. If anyone knows a way to make this happen, I would appreciate some insight. --Leon Link to comment Share on other sites More sharing options...
blueman2 Posted October 31, 2020 Share Posted October 31, 2020 31 minutes ago, LFMc said: Hi All, I was hoping to find an easy way to do this, but I have not found it. I need to enter a value into an ISY (v 4.7.5) variable with the Insteon 2441TH set point temp and the current temperature. Also I would like to direct set the thermostat's set point from a variable. I have found no way to put the temps into a variable. I can put the thermostat into a known/fixed set point and then increase or decrease the temp in one degree increments accordingly, but I have found that the thermostat occasionally doesn't respond to the up/down 1 degree command and I have no way of knowing that occurred. If anyone knows a way to make this happen, I would appreciate some insight. --Leon Every time the temperature (either the setting or actual) changes, it will update the variable. Link to comment Share on other sites More sharing options...
TrojanHorse Posted November 1, 2020 Share Posted November 1, 2020 Hi All, I was hoping to find an easy way to do this, but I have not found it. I need to enter a value into an ISY (v 4.7.5) variable with the Insteon 2441TH set point temp and the current temperature. Also I would like to direct set the thermostat's set point from a variable. I have found no way to put the temps into a variable. I can put the thermostat into a known/fixed set point and then increase or decrease the temp in one degree increments accordingly, but I have found that the thermostat occasionally doesn't respond to the up/down 1 degree command and I have no way of knowing that occurred. If anyone knows a way to make this happen, I would appreciate some insight. --LeonYou need v5 firmware. Sent from my iPhone using Tapatalk Link to comment Share on other sites More sharing options...
blueman2 Posted November 1, 2020 Share Posted November 1, 2020 Yup, sorry I forgot this was new in V5. I have been on V5 for so many years, I forgot! Link to comment Share on other sites More sharing options...
larryllix Posted November 1, 2020 Share Posted November 1, 2020 4 hours ago, LFMc said: Hi All, I was hoping to find an easy way to do this, but I have not found it. I need to enter a value into an ISY (v 4.7.5) variable with the Insteon 2441TH set point temp and the current temperature. Also I would like to direct set the thermostat's set point from a variable. I have found no way to put the temps into a variable. I can put the thermostat into a known/fixed set point and then increase or decrease the temp in one degree increments accordingly, but I have found that the thermostat occasionally doesn't respond to the up/down 1 degree command and I have no way of knowing that occurred. If anyone knows a way to make this happen, I would appreciate some insight. --Leon You can do it in V4 with a series of programs...one for each degree that installs a value into the variable. Each program progressively tests for a higher value until one either becomes true, or calls the next program in the chain. I suggest getting V5 instead. Link to comment Share on other sites More sharing options...
LFMc Posted November 1, 2020 Author Share Posted November 1, 2020 8 hours ago, larryllix said: I suggest getting V5 instead. OK, I guess I have been waiting for a good reason (for me) to switch to V5, this may be it. 9 hours ago, blueman2 said: I have been on V5 for so many years, I forgot! Lol. Nice way of suggesting I catch up with the times. (-; Thanks all! Link to comment Share on other sites More sharing options...
larryllix Posted November 1, 2020 Share Posted November 1, 2020 2 hours ago, LFMc said: OK, I guess I have been waiting for a good reason (for me) to switch to V5, this may be it. Lol. Nice way of suggesting I catch up with the times. (-; Thanks all! You won't regret it. Very few have had problems upgrading. You may like the decimal values available with v5 and many other features I take for granted now. Programs with conversion problems will have yellow avatars and line will be commented by the conversion. You will need to check your Insteon scenes as some of those may have hidden problems. I use as few scenes as possible, for other reasons so I wasn't bothered by scenes three years ago when I went to v5.0.0. backup...backup...backup! Just in case. Link to comment Share on other sites More sharing options...
Recommended Posts
Archived
This topic is now archived and is closed to further replies.