Chuck Posted May 11, 2010 Posted May 11, 2010 I have had a pretty reliable setup until a few days ago when I noticed a switchlinc dimmer not responding to scenes. I also noticed in the admin console it showed up with a different green icon next to it. The icon changed back to normal when I did a query on the device today. The device level and ramp rates within scenes show as comepletely different settings than it was originally set for. When I 1st open the admin console and try to correct the level or ramp rate for this device inside a scene, I get: [-110022] Couldn't open file [/CONF.ADR.CFG] [-110022] Couldn't open file [/CONF.FYP.CFG] And upon further attempts I get, "Request Failed". I can succesfully query the device and change it's default levels. Please help. Chuck
Michel Kohanim Posted May 11, 2010 Posted May 11, 2010 Hi Chuck, What does the Admin Console report for the version of this Switch? If v35, then rest assured the problem is the switch itself and that it must be replaced. With kind regards, Michel
Michel Kohanim Posted May 13, 2010 Posted May 13, 2010 Hi Chuck, Thanks and no, this is not one of the bad ones! What ISY firmware version are you on? Can you verify if you have this problem whether or not the load is ON for this device? i.e. what happens if you turn off the switch and then query and/or try programming it? With kind regards, Michel
Chuck Posted May 13, 2010 Author Posted May 13, 2010 I'm using v.2.7.14. I tried to upgrade to 15 and get, "Upgrade failed:invalid or incompatible upgrade file". The problem exists with the device on or off.
Michel Kohanim Posted May 13, 2010 Posted May 13, 2010 Hi Chuck, Please use Help | Automatically Upgrade My Lighting to do the upgrade. I think you might be using the upgrade file for ISY26. Ok, next test is to turn OFF all devices in your system (All Off) and retry. If that also fails, then please let me know if you have any SignaLinc RFs (with the Antenna). If not, how many access points do you have? With kind regards, Michel
Chuck Posted May 13, 2010 Author Posted May 13, 2010 After pressing "ALL OFF", I still get "Request Failed" when trying to adjust the device settings within any scene. I do not use any SignalLink RFs or Access Points. The system has been working for over a year up to this point. Thanks, Chuck
Michel Kohanim Posted May 14, 2010 Posted May 14, 2010 Hi Chuck, At this point I have to think that either your PLM has gone bad or something is blocking the signal from the PLM. Two more questions: 1. Do you have any LampLincs? If so, can you plug one right onto the PLM and try changing the settings 2. Have you recently moved your ISY/PLM OR have you recently installed a new piece of equipment anywhere? With kind regards, Michel
Chuck Posted May 14, 2010 Author Posted May 14, 2010 Michel, I plugged a LampLinc (2456D3 v.28) directly into the PLM and could succesfully change it's default settings and settings within scenes. I have not moved the ISY/PLM and have not added anything. Thanks, Chuck
Chuck Posted May 14, 2010 Author Posted May 14, 2010 (That's supposed to be "v.28", not a smiley face in that last post)
Michel Kohanim Posted May 15, 2010 Posted May 15, 2010 Hi Chuck, So, this test tells me that your PLM is OK. So, there HAS to be some type of signal issue or a defective device. The only way to diagnose - and although quite difficult - is to take out the switch and then plug it into the same outlet as the PLM. If that works, then we have to figure out where the signal is getting lost. If that does not work then you have a defective switch. With kind regards, Michel
Chuck Posted May 18, 2010 Author Posted May 18, 2010 Michel, I replaced the device and had the same errors, even when powered directly into the PLM. I removed the device and added it as a new device and manually added it into all the scenes and programs and that worked. A pain, but it worked. I'm not sure why. Chuck
Michel Kohanim Posted May 18, 2010 Posted May 18, 2010 Hi Chuck, This is quite strange. By replace do you mean actually replacing it with a new device? With kind regards, Michel
Chuck Posted May 18, 2010 Author Posted May 18, 2010 Yes, I replaced it. I was initially planning on selling Insteon (I own an electronics integration business), so I have some in stock.
Michel Kohanim Posted May 19, 2010 Posted May 19, 2010 Hi Chuck, thank you. This is quite strange ... please do keep me posted if you experience anything similar with other devices in your network. With kind regards, Michel
Chuck Posted May 28, 2010 Author Posted May 28, 2010 Michel, Now the new device is showing the same symtoms! The icon next to it in the admin console is green and all associated scenes show the ramp rate as 9m. The first attempt at changing the ramp rate within a scene results in: [-110022] Couldn't open file [/CONF.ADR.CFG] [-110022] Couldn't open file [/CONF.FYP.CFG] Subsequent tries result in "Request Failed". Please help. Thanks.
Michel Kohanim Posted May 28, 2010 Posted May 28, 2010 Hi Chuck, I think it's now time for getting in contact with our tech support team. Personally, I can only think of two things causing this issue: 1. A defective PLM 2. Some device on your network started going bad and is causing all sorts of network traffic/noise and thus all the comm errors Does your PLM blink continuously on its own even though there should not be any traffic? With kind regards, Michel
Chuck Posted August 18, 2010 Author Posted August 18, 2010 Michel, I am hoping to get this resolved. You mentioned getting in contact with your tech support team. Please have them contact me. Thanks, Chuck chuck@professionalavi.com 319-430-2482
Michel Kohanim Posted August 18, 2010 Posted August 18, 2010 Hi Chuck, Apologies for the confusion ... I meant that you can call our tech support team and we'll login to your system to see what's going on. Our tech department is open from 9:00 AM to 4:00 PM PDT. Phone number is 818-631-0333. Please call at your convenience. With kind regards, Michel
Recommended Posts