ingeborgdot

I am putting a fantech inline fan in my bathroom. I am wanting to use an insteon switch of some sort to control the time on but also be able to control it somewhat with the isy. I also want to control the fan speed. They tell me that the fan speed can be controlled and am wondering what someone would use from insteon for that? Sometimes I would just like it to run for an extended period of time but at a low level because this fan has so much suction on high I have had to hold on to something so I did not get sucked out of the room I want to tone it down a little sometimes. Thanks.

That sucks. I guess I just assumed that they could dim. I need to look at description again because I don't find anywhere that says it does not dim. That kind of defeats my purpose for having them. I am stuck with 2 devices that don't work for me now.

Does the outletlinc not work as a dimmer? I thought that I would be able to use it as a dimmer like the lamplincs would? I put it in a scene with a KPL and it only turns on and off. Did I miss something? Please help.

Is there another place I could go to get an answer?

I have just installed the venstar 1800 and have a question and a little problem. When I go into the isy and set it the mode I set it for program/heat right now. My problem is that after a day or so it goes into the off mode and I have to go in and start it again. What could be causing this. I have the fan set to run to circulate air for 10 minutes from 10-10 every day. Could that be it. I don't have it programmed in the isy to do anything yet, just in the thermostat itself. Is there some other setting that I may have done that is causing this? Thanks.

I may try it but what if the program that I used is running without any problems. It stays off during the day now. It turns on when it is supposed to. I don't know but it works right now.

I may be overlooking it, but I see five programs, labeled programs 1, 2, 3, 4, and 5. I see no program labeled "A2.BackYard Lights on 3 Minutes" or 'A1.BackYard Motion Sensed'. I see no device in your program called "back door light" What are the folder conditions? My bad, I meant back porch light. Conditions?

I relabeled the programs for you.

My two switches are in a scene. Nothing else. My back porch light, and garage light are the two lights that are controlled.

Go back up and look at the folder that I previously stated. I edited with more info about program #s. Is that what you mean????

a. yes b. yes c. yes d. yes e. yes f. yes Sorry about bad practices.

Well, here is where my ignorance comes to play. After re doing all of what you see, do I need to go to my ms and reset it?

oberkc, what would you do? Would you make a folder? Do you have an alternative to what I have? Thanks.

The back door light and garage light are in my scene.

Here is what I just got done writing before you wrote to me. I put it in a folder and wrote 5 programs. I will have to check to see if it works. A1. BackYard Motion Sensed If From Sunset To Sunrise (next day) And Control 'MS Garage' is switched On And Control 'MS House' is switched On And Status 'Back Porch Light' is not On And Status 'Garage Light' is not On And Program 'A2.BackYard Lights on 3 Minutes' is False Then Run Program 'A2.BackYard Lights on 3 Minutes' (Then Path) Else - No Actions - (To add one, press 'Action') A2.BackYard Lights on 3 Minutes If - No Conditions - (To add one, press 'Schedule' or 'Condition') Then Set Scene 'BackYard Lighting' On Wait 3 minutes Set Scene 'BackYard Lighting' Off Run Program 'A2.BackYard Lights on 3 Minutes' (Else Path) Else - No Actions - (To add one, press 'Action') Turns backyard lights on for 3 minutes. A program is used such that the 'wait' is not reinitialized by new events triggering 'If conditions'. A3. BackYard Lights Switched On If Control 'Back Porch Light' is switched On And Control 'Garage Light' is switched On Then Stop program 'A1.BackYard Motion Sensed' Enable Program 'A1.BackYard Motion Sensed' Run Program 'A2.BackYard Lights on 3 Minutes' (Else Path) Else - No Actions - (To add one, press 'Action') This programs returns control to motion sensor and reinstialzes the condition logic flags. Run prgram (else path) to reset the motion on/off flag. A4. BackYard Lights Switched Off If Control 'Back Porch Light' is switched Off And Control 'Garage Light' is switched Off Then Stop program 'A1.BackYard Motion Sensed' Disable Program 'A1.BackYard Motion Sensed' Run Program 'A2.BackYard Lights on 3 Minutes' (Else Path) Else - No Actions - (To add one, press 'Action') Double tap (off) disables the motion sensor such that the porch light stays off until the switch is manually turned on again. Purpose of the 'Run Program' (else path) is the reset the motion on/off flag. A5. BackYard Lights Daily Reset If Time is Sunrise + 30 minutes Then Set 'Back Porch Light' Off Set 'Garage Light' Off Run Program 'A2.BackYard Lights on 3 Minutes' (Else Path) Enable Program 'A1.BackYard Motion Sensed' Else - No Actions - (To add one, press 'Action') Turns off backyard lights 30 minutes after dawn and resets the program flags in case the lights were manually overridden and left on all night. What does this look like to people?

Well, I have just been re doing the programming in the isy for the 2 ms in my back yard. The 2 sensors run the same two lights. The programming of this is kicking my behind. I had it working, (I thought) but for some reason it started turning on in the day and I have not been able to get it fixed. Everyone on here has given me advice but it has been a little bit here and a little there that I am just getting confused. I am not a wizard at this like the rest of you on here. I do a program and then maybe don't do another one for 6 months or so. I kind of forget things sometimes. If someone would just give me a program in full that would work for the 2 ms for the 2 lights that I have in a scene together I would be forever in your debt. I want them to turn on only in the night and have it shut off after about 3-5 minutes. I think I have it that the ms are what controls the off time so I don't think I need something there unless everyone feels that is needed. That is all I need this to do. I have a ms in the front and have it programmed with no problems. It is the 2 ms that is beating me to death. The one in front is put into a folder that was done over a year ago and it still works great. I am not sure if that maybe putting this into a folder would work better or not. The problem is I have to figure out how a folder works again. Rand helped me out with it so I would have to try to figure it out. If someone would please be so kind as to help I would thank you greatly.

I have a question about after changing the programs on my 2 ms. If I change the program, do I need to do anything to the ms or just the switches to reset them to take the new program? Thanks.

Works.

Yep, I will delete the older and superfluous ones.

It is because I have too many scenes with them in it is the problem. It should be solved when I make one scene and put them all in it. I am still learning and you guys are great teachers. I just don't work with it enough to get real good at it.

Okay, I am out to lunch. I forgot about a couple of things that I should explain much better if I can. Example: East Counter lights are on a main switchlinc, a remote linc, a KPL downstairs and a KPL in the kitchen. How should I set all of these up? On one scene? My problem has been it won't let me choose as a controller. Example: West Counter Lights are on a main switchlinc, a remotelinc and a KPL. Sink light is on a main switchlinc, a remotelinc and a KPL.

Okay, let's see if I can explain correctly. In the kitchen I have switches on the south wall and at the other end of the room the KPL that has some of the buttons that control those switches. I need to be able to turn on and off from both places. When I turn on the lights from the switchlinc switch they turn on fine but the button on the KPL that corresponds with that light does not. If I turn on the light from the KPL the button lights up and the switchlinc on the other wall also lights up. Why does the KPL not light up when the switchlinc is turned on?

I do have an issue that I think I can solve but when I turn on the light that also is run by that KPL it does not light up the button any brighter than the original. When I turn it on at the KPL it lights up brighter. I can control it fine with my computer etc.

It keeps saying request failed.

I just got it a week ago.