Everything posted by pjjameso
-
WAF Open/Close vs On/Off
Is there a way to have the commands open and close in addition to on off? Use portal to control Curtains and saying turn on Curtains vs close Curtains would help on the wife acceptance factor.
-
What is ZWave Multi Channel, Does ISY Support?
Michel, Any luck with the MIMO2+? On another note will pull out the Fibaro and try to re install and send the results. As mentioned worked great with 4.62, not at all with 5.011b
-
What is ZWave Multi Channel, Does ISY Support?
Unfortunately my curtains require 2 relays.... one to trigger open, one to trigger close, and really a third to have them stop in between but i can live without that one. The motor attaches to a pull cord and contains sensors to tell when fully open or closed, eg no lever setting.
-
What is ZWave Multi Channel, Does ISY Support?
Michel, Any luck with the MIMO2+? Would like to remove the home assistant on rpi asap.
-
Home Assistant and ISY Portal Node
Well good news, all up and running and ISY and Home Assistant with the Aeotec Z Wave Stick are working great. I can press an insteon keypad button and control the zwave device.Gen 5 here we go!. Would still more eloquent when Gen 5 is supported with a new daughter card. But for now I am all set..
-
Home Assistant and ISY Portal Node
Any idea where to find the entity id in the ISY to use in Home Assistant?
-
Home Assistant and ISY Portal Node
Okay think I found the answer and it appears easier than thought. Will let you know how I make out. HANDLING INSTEON CONTROL EVENTS A Home Assistant isy994_control event is emitted for every “control” event in the Insteon network. This allows you to write automations that trigger based on Insteon button presses. You can also trigger off of the unique Insteon events, such as double-presses, long-holds etc. automation: - alias: turn off living room on double tap lightswitch trigger: platform: event event_type: isy994_control event_data: entity_id: light.lr_track_lights_front control: 'DFOF' action: service: light.turn_off entity_id: light.lr_track_lights_rear All isy994_control events will have an entity_id and control parameter in its event_data. You’ll need to refer to ISY994 documentation for the list of every possible control type, but the common ones are: DON: On button DOF: Off button DFON: “Fast On”, usually from double-tapping an On button DFOF: “Fast Off”, usually from double-tapping an Off button FDUP: “Fade Up”, usually while holding down an On button FDDOWN: “Fade Down”, usually while holding down an Off button FDSTOP: “Fade Stop”, when releasing a long-held button BRT: “Brighten”, from controllers that issue a single command to slightly brighten a light DIM: “Dim”, from controllers that issue a single command to slightly dim a light
-
Home Assistant and ISY Portal Node
So I have no clue as to what I’m talking about so bear with me.... On 5.0.11b but still have issues with multi channel zwave devices (MIMO2+) which Michel has kindly indicated he will research. What I am wondering is how one could one go about using Home Assistant to control zwave devices while keeping in sync via isy node server which would allow me to use insteon keypads and programs to control said zwave devices? A bit Rube Goldberg but would solve gen5 zwave device issues till ISY daughter card is available. There are already ISY 994 HA components developed to control devices via the ISY. Figure for 70 bucks it would be worth he effort, just need a bit of direction from someone. Basically I am trying to get control of the two relays on the mimo.
-
What is ZWave Multi Channel, Does ISY Support?
You rock Michel! Thank you so much for debugging the MIMO2+. It will solve a host of issues (automation) for me!
-
Should I be looking to transition to Z-wave from Insteon?
Michel Im on 5.0.11b and FortezZ MIMO2+ ISY only recognizes sensor 1 and relay 1. This is a multichannel device so should be seeing sensor 2 and relay 2 as well. Would be fantastic if you could take a look and see what wrong in the alpha code. Have tried including/excluding multiple times, repairing, syncing etc.
-
ZWave Node Increment
On version 5.0.11b, I have removed by exclusion all the zwave devices, removed leftovers by removing failed nodes, syncronized nodes, healed zwave network. Assume I would be starting from scratch at this point yet when I add new zwave device it starts at a higner number eg ZW 11. Why would it not start at ZW 01?
-
Tried to revert to 4.6.2 from 5.011b
Fixed the mess by removing sd card, formatting, installing 5.0.11b firmware, and restoring 5.0 backup version I had made earlier. Guess I’ll stick with 5.0 for the time being.
-
What is ZWave Multi Channel, Does ISY Support?
Thank you for your zwave thoughts. Agree was hoping ISY would solve some of my automation quests. Unfortunately unable to get insteon devices for some of those quests hence trying to use zwave. Able to get tilt zwave tilt sensor to work at the mailbox whereby ISY sends notification. However most other zwave devices seem to be a bust especially with 5:0:11b. Fibaro worked in 4.6.2 not in 5.0, along with mimo2+ only controlling one relay and sensor vs 2 in both 4.6 and 5.0. Also 5.0.11b broke Simple Controls app executing scenes. Still works for individual device control but not for scene execution. Can’t figure that one out... can execute scene in ISY and using ekPro but no longer with simple control app. Looks like latest 5.0.11b version was just released, anybody have an off the record guess as to when gen5 dongle will be released along with software version to enable? To be honest don’t care much about Alexa control (although I do use the portal) would much rather have complete zwave control. Wish team would focus on that work stream vs others. ISY is a fantastic product (elk, REST integration etc).....guess I’m just too impatient.
-
What is ZWave Multi Channel, Does ISY Support?
Thanks for the info, im with you... I give up on getting zwave devices to work with the ISY. Will need to brush up on my REST commands but assume I can send a command from a insteon keypad or isy program to the Aeon zwave to execute an action, correct?
-
What is ZWave Multi Channel, Does ISY Support?
Michel, No go on getting the MIMO2+ to recognize relay 2 nor the sensor 2. Also havent been able to get the Fibaro multi sensor to work under 5.0 as it was under 4.62. Any thoughts?
-
Tried to revert to 4.6.2 from 5.011b
And now nothing but red flashing error light on ISY. Any idea on how to recover from my stupidity?
-
What is ZWave Multi Channel, Does ISY Support?
Bit the bullet and upgraded to 5.0.11b and still only showing one relay. Any idea when ISY will support MultiChannel Command Class used by MIMO2+?
-
What is ZWave Multi Channel, Does ISY Support?
Need to control Curtains and bought the mimo2+ but only able to control one relay. Says need multi channel zwave controller. Does/will ISY support? Also just bought Vision curtain control but afraid will have the same issue. What’s your guys thoughts? Running 4.62 but ready to upgrade to 5.0 if that will solve my issue.
-
Geofence Application
Xathros, Thank you so much for the enhancement! Makes sense, will give it a go when Im back home long enough to play (program!) Curious as to why Michaels method using nodes would be any better than setting a state variable. What am I missing (not that i have v 5 installed)?
-
Geofence Application
Using Geofency app to indicate whether Im home or not to send a post command to set a state variable (1 Home, 0 Away). Would like to have the alarm turned off when I arrive but not interfere when im setting the alarm and leaving the house. I believe the following program will work but was wondering if there was a more eloquent method you may suggest. Paul Away - [iD 0049][Parent 004A] If Elk Area 'The Jameson's' 'Arm Up State' is Armed with Exit Timer Then Wait 5 minutes Enable Program 'Paul Home' Else - No Actions - (To add one, press 'Action') Paul Home - [iD 0048][Parent 004A][Not Enabled] If $sPaul.Is.Home is 1 And Elk Area 'The Jameson's' 'Armed State' is Armed Away Then Set Scene 'Welcome Home' On Set Elk Area 'The Jameson's' Disarm Wait 5 minutes Set '1st Floor / Kitchen / Camera On-Off Bot' Off Disable Program 'Paul Home' Else - No Actions - (To add one, press 'Action')
-
Unsupported Device 3.17; New PowerLinc Rev 2.3
Hi Teken, The Pronto rfx9600 is sending the commands from the pronto 9600 remote to trigger scenes. Have a few setup, movie time, intermission, reading, etc. Pronto remote controls all the AV equipment and NAS with icons for TV channels. Works extremely well, aka meets the wife acceptance factor!
-
Unsupported Device 3.17; New PowerLinc Rev 2.3
Poked around a bit more after Teken's suggestion above... Appears the old PLM version shows the same message in the Admin Console, Unsupported Device 3.17. Guess I just never noticed as everything was working properly... Thanks for the assist!
-
Unsupported Device 3.17; New PowerLinc Rev 2.3
Hi Teken, Im not using it as a PLM.... it hooked up to a serial port to a Pronto RFX 9600 controlling lights,etc. Previous versions of the PowerLinc were properly classified when Linked. Is anyone else using this version of a PowerLinc and had it recognized by the ISY? BTW the device is working properly, just shows unsupported in the ISY Admin Console.
-
Unsupported Device 3.17; New PowerLinc Rev 2.3
My PLM bit the dusk last week so ordered a replacement from SmartHome. Its a PowerLinc Modem Serial Interface (Dual Band) 2413S Revision 2.3 4216. Error keeps coming up with unsupported device if I manually select add new PowerLinc or try via the set button on the unit. Any thoughts on how to correct?
-
Does android lollipop work fine with mobilinc?
MobilLinc does not work with the non pro 994i version on Lollipop. Had to upgrade to the Pro version ($30) and then suffer with slow response with cell data connections. I would just stick with KitKat.