smokegrub

How do I do that?

I have a MacBook Pro running Mavericks. My router is an Airport Extreme. The router can be configured using Airport Extreme 6.3.2. I want to configure the ISY994 to allow access by both the local IP and the external IP. I can already access the ISY remotely using MobiLinc Pro which shows a local port (80), a Secure https (the external port of the router), a Secure Port (443), a Connect Method (Auto (HTTP) and the UUID of the ISY. How/where do I set up the ISY to allow access in the same manner?

Reprogrammed the light and fan speeds and all is well now.

I wrote Smarthome inquiring about my inability to get audio from my Insteon camera and their software running on a Mac. Here is their reply: Thank you for contacting Smarthome. The cameras audio works on windows computers through Active X, There was an older version of the VLC plugin that supported it for mac, however I do not believe that the current version does. Beware of this deficiency if you have a Mac and plan to use this camera and expect audio.

They are incandescent. As I posted earlier, the strange thing is that I can turn the light on/off without fail using either the admin console or MobiLinc. The KPL fails occasionally but will begin working if I manage the light for one cycle on/off using the admin console or MobiLinc.

Allow me to re-phrase the question about programming: The FanLinc shows up as two devices on the ISY, FanLinc Light and FanLinc Motor. To get the light to work I created a scene with the KPL "On" button as the controller and FanLinc Light as the responder. Is that the proper way set up the KPL button?

Each switch LED flickers when activated. Note that the fan buttons work as programmed all the time. Only the light is presenting a problem. Are there instructions as to how to properly program the scene for the light?

The On/Off button (6 button KPL) for the light on a ceiling fan (FanLinc controlled) flickers when pressed On/Off and occasionally works. The fan speeds consistently work from the keypad. When accessed from the app or from MobiLinc On/Off works consistently. When pressed at the KPL and it fails to work, using the app or MobiLinc to turn it on or off results in the switch on the KPL working again for a while but flickering when it does so. I am stumped. ISY994

Will this variation of your suggestion work? if status KPLD is on then set device C on set device B on wait 2 minutes set device C off set scene with KPLD off else nothing

oberkc: That is precisely what I am trying to do but I cannot find the KPL Off command. Where is it located?

I am trying to write a program that does the following: If KPL button D is on, turn devices B and C on. Wait 2 minutes and turn device C off. I am able to program that successfully but after device C turns off I would like to program KPL button D to go to its off state. Is that possible? If so, how?

Problem solved. Thank you, LeeG.

I have a folder that contains several programs on my ISY94i. The folder is assigned to a button on a KPL and runs fine when the button is activated. However, I can find no way to activate the button using MobiLinc Pro. Suggestions?

The factory reset worked. I am left wondering' however, what the root problem is. Thanks for the help.

I tried two separate circuits and neither helped. I hate to do a factory reset of the device because of the ripple effect in various scenes. Do you think I should try that? It seems my last option.

Great idea. The simplest tests often elude me!

Nothing has changed but there is a power strip near where the ISY is located. That strip may be on the same circuit as the subject device. The modem, router and a printer are plugged into it. Do you think I should plug all the aforementioned devices directly into an outlet and remove the strip altogether?

I wrote updates as directed with no change in status. I also tried to relink it on the 3-way circuit using the ISY. It would not link. It has been working well for several days prior to this incident.

I have a device that now has a green logo of some sort next to it and the subject message. It also says to "Please check communications". I tried restoring the device and that did not work. What do I need to do that will not mess up all the places where this device is used in a scene?

Thanks. Other than being a nuisance, it works. That is more than I had.

The desktop icon.

It works, once. Then I must empty the Java cache and download a new app for it to work again.

Thanks, Lee.

When I switch to Status for the KPL button, there is no ON option available. There is Responding, OFF and a percentage range of options. Why is the ON option not available?

I did use a different scene for each button. Each button is a controller for that scene and each os the remaining buttons is a responder. The FanLinc Motor is the node. My problem is setting the On/Off status of the responder buttons.