tibbar

Hi. I have a submersible well pump that is 130 ft deep. Once a while for reasons unknown pump will loose a prime and I may have to cycle power couple times for it to kick in. I bought and installed Aeon Labs Aeotec Zwave Heavy Duty Appliance Smart Switch ZW078. The switch is also energy meter and under a status is will display Watts used at the moment. Need help with program that would cycle the pump. Can you guys tell me whats wrong with my program, because something is.: Well Pump Low - [iD 0059][Parent 0001] If 'Well Pump On-Off ZW 057 / ZW 057 Energy Meter' Status > 200.000 Watts And 'Well Pump On-Off ZW 057 / ZW 057 Energy Meter' Status < 900.000 Watts Then Send Notification to 'Robert' content 'Power' Set Elk Output 'Output 111' On Wait 30 seconds Set 'Well Pump On-Off ZW 057' Off Wait 2 minutes Set 'Well Pump On-Off ZW 057' On Else - No Actions - (To add one, press 'Action') P.S When pump is pumping water it draws 950 Watts und up and when it looses prime it's anywhere from 600 to 800. Thanks

Z-Wave, ELV, Instant Status: https://www.amazon.com/gp/product/B001HT4M3E/ref=ox_sc_sfl_title_98?ie=UTF8&psc=1&smid=ATVPDKIKX0DER

Hi. Tried connecting bosch motion detector to Mimo2+. I can see led coming on on Mimo board but nothing in ISY console. It looks like this all the time.

Hi. I've tried: 1. Exclude from ISY 2. Factory reset Mimo 3. Include to ISY NO change - same results. Here is a log when querying the Mimo2+ Multilevel Sensor: Sat 09/30/2017 02:13:02 AM : [ZWAVE-TX ZW056_1] [98/40] Security Nonce Get ACK,AUTO,EXPLORE To=0x38 Sat 09/30/2017 02:13:02 AM : [ZWAVE-RX ] [0104011301E8] [00/00] CC=0x00 cmd=0x00 [] ACK,AUTO,EXPLORE Sat 09/30/2017 02:13:02 AM : [ZWAVE-RX ] [010500130B00E2] [00/00] CC=0x00 cmd=0x00 [] ACK,AUTO,EXPLORE Sat 09/30/2017 02:13:02 AM : [ZWAVE-RX ZW056_1] [98/80] Security Nonce Report - nonce=[3BF7FADEAFDEBB73] ACK,AUTO,EXPLORE From=0x38 Sat 09/30/2017 02:13:02 AM : [ZWAVE-TX ZW056_1] [98/81] Security cmd=0x81 [1F487285E802B23F2A23B03B53E02D60A21A3701] ACK,AUTO,EXPLORE To=0x38 Sat 09/30/2017 02:13:02 AM : [ZWAVE-RX ] [0104011301E8] [00/00] CC=0x00 cmd=0x00 [] ACK,AUTO,EXPLORE Sat 09/30/2017 02:13:02 AM : [ZWAVE-RX ] [010500130C00E5] [00/00] CC=0x00 cmd=0x00 [] ACK,AUTO,EXPLORE Sat 09/30/2017 02:13:02 AM : [ZWAVE-RX ZW056_1] [98/40] Security Nonce Get ACK,AUTO,EXPLORE From=0x38 Sat 09/30/2017 02:13:02 AM : [ZWAVE-TX ] ... Sat 09/30/2017 02:13:02 AM : [ZWAVE-RX ] [0104011301E8] [00/00] CC=0x00 cmd=0x00 [] ACK,AUTO,EXPLORE Sat 09/30/2017 02:13:02 AM : [ZWAVE-RX ] [010500130D00E4] [00/00] CC=0x00 cmd=0x00 [] ACK,AUTO,EXPLORE Sat 09/30/2017 02:13:02 AM : [ZWAVE-RX ZW056_1] [98/81] Security cmd=0x81 [7D743A8B67C3C7D1014C4E321BD707463D35E19B89] ACK,AUTO,EXPLORE From=0x38 Sat 09/30/2017 02:13:02 AM : [ZWAVE-RD ZW056_1] [25/03] Binary Switch Report val=0x00 ACK,AUTO,EXPLORE From=0x38 Sat 09/30/2017 02:13:02 AM : [ZWAVE-TX ZW056_1] [31/01] CC=0x31 cmd=0x01 [] ACK,AUTO,EXPLORE To=0x38 Sat 09/30/2017 02:13:02 AM : [ZWAVE-RX ] [0104011301E8] [00/00] CC=0x00 cmd=0x00 [] ACK,AUTO,EXPLORE Sat 09/30/2017 02:13:02 AM : [ZWAVE-RX ] [010500130F00E6] [00/00] CC=0x00 cmd=0x00 [] ACK,AUTO,EXPLORE Sat 09/30/2017 02:13:07 AM : [ZWAVE-TX ZW056_1] [31/01] CC=0x31 cmd=0x01 [] ACK,AUTO,EXPLORE To=0x38 Sat 09/30/2017 02:13:07 AM : [ZWAVE-RX ] [0104011301E8] [00/00] CC=0x00 cmd=0x00 [] ACK,AUTO,EXPLORE Sat 09/30/2017 02:13:07 AM : [ZWAVE-RX ] [010500130F00E6] [00/00] CC=0x00 cmd=0x00 [] ACK,AUTO,EXPLORE Sat 09/30/2017 02:13:12 AM : [ZWAVE-TX ZW056_1] [31/01] CC=0x31 cmd=0x01 [] ACK,AUTO,EXPLORE To=0x38 Sat 09/30/2017 02:13:12 AM : [ZWAVE-RX ] [0104011301E8] [00/00] CC=0x00 cmd=0x00 [] ACK,AUTO,EXPLORE Sat 09/30/2017 02:13:12 AM : [ZWAVE-RX ] [010500130F00E6] [00/00] CC=0x00 cmd=0x00 [] ACK,AUTO,EXPLORE Sat 09/30/2017 02:13:17 AM : [ZW-TX-FAILED] 56.0/0x31.01

Hi. I just received my first Mimo2+. Included it to ISY. It shows as: _1 Multilevel Sensor and _147 Binary Switch I'm trying it with my NICE APPOLO 1050 gate opener. 1. Connected Sig1 to gate output- programed for gate MOVING. 2. Connected Relay1 to gate input - programed for STEP operation. I can control the gate operation with ISY so the switch part works but ISY does not sense the gate moving. With the gate moving I can see SIG1 led on Mmo2+ control board change status (so it is receiving signal from gate) but ISY is not aware of it. Gate motherboard has NC, COM, NO connections for output. I tryed combination of NC+COM and NO+COM with same effect. Is there anything else I should do? P.S. I'm on 5.0.10- looks like multichannel is not working right with Mimo2+. Thanks.

What about any of v5. alphas? I could use 2 relays . Zwave plus is also nice.

Hi. I would like to add Zwave in-out module to my install. Found MimoLite and Mimo2+. Mimo2+ looks like a better device with 2in and 2 out signals and Zwave Plus. Is Mimo2+ supported by ISY? Thanks

Thanks. I got it working now. Special thanks go to Jackal and Barry Gordon.

Hi. Not sure if I'm blind today or just have a brain **** but for life of me I can't find any instructions on setting up Echo with ISY without portal using RaspberryPi. Could someone please point me in right direction. Thanks.

Thanks guys. ISY time is correct. I'll give the two program approach (looks good) tomorrow during day time hours.

Kitchen Door Open - [iD 0005][Parent 0001] If From Sunset + 15 minutes To Sunrise - 15 minutes (next day) And Control 'ZW Kitchen Door Lock' is switched Key/Manually Unlocked Then Set Scene 'Sofit / Sofit Backlanding' On Set Scene 'Sofit / Sofit Deck' Fast On Set Scene 'Sofit / Sofit Driveway' Fast On Set Scene 'Outside Rec Driveway' On Set Scene 'Garage Front Outside' On Else - No Actions - (To add one, press 'Action') This has run fine for quite a while but after last couple updates (current v.4.3.26) but lately light come on when the door is open in the middle of the day- why? What I would like is to lights to turn on when the door lock is unlocked but only when is "dark"- - 15 min after sunset to 15 min before sunrise. Any ideas?

I've figured out the problem. I'm using Vera3 for my zwave door locks and thermostat and I had a Denon plugin running Which is using telnet ( I guess) and could not connect to denon with Isy. As soon as I shot down Vera everything was good.

Hello. I'm tring this with AVR-3312ci but no luck. Anybody willing to help. It is the only reason I just purchased network module. Thanks.