paulbates

Congrats! Because rachio requires an oauth2 based token, the ISY is unable to talk to it directly. A "middle man" interface is needed to manage the token. I have the rainmachine and it has the same ISY challenge One common developer approach: Using ISY V5 firmware and a creating a nodeserver. The nodeserver is an interface that talks to your rachio on one end, and ISY devices it creates on the other. This is becoming the common approach for this exact type of technical requirement. The primary language for nodeservers is Python, and the ISY Python support framework is named Polyglot. If you are handy in linux/python, there are a number of examples and members in that part of the forum that would be happy to help out if you post there. Polyglot requires studying the link topics, but is one of the straightest paths to meet your requirement Note that ISY V5 Firmwares are considered alpha/beta depending which version you use. Paul

I have one on a stake under my deck as a "critter detector" (primarily skunks at night). It triggers photonic beam weaponry ...e.g. a landscape flood light. I thought about the sprinkler angle, but over time it triggers less and less. I think they've gotten the message Paul

The insteon motion sensor is sold as indoor/outdoor and can take cold and heat all day long. For me that's ~-20F to ~105F. However... heavy, continuous downpours knock them out...for good. I believe water comes through the lens seal as well as where the case and battery door pull apart. Mount it under the eves, or provide cover for the unit from above, out and over the front Paul

Hi- In the admin console, click on the iolinc, and then click options on the bottom center of the panel. If "relay follows input" is checked, uncheck it. This is the likely culprit. Test operation of the door from all controllers, GDO remotes to make sure it works Paul

It comes down to: every thermostat model has benefits and warts. You have to decide what you can live with. Its not uncommon for people to try a couple out. If there are any you can return after trying for a few weeks, it would probably be worth trying them and see what you like. Paul

Hi John, welcome to the forums! On the Link Management menu there is a option for New Insteon Device. You can use the Device Type drop down and pick the 4.0 EzRain/EzFlora specifically. Give that a try. Paul

@larryllix, somewhere in the forums you did an exhaustive comparison of TSTATs that covers a number of the ones discussed here and their trade offs. Can you post a link to that? Paul

Dan Node device status can be copied to variables, and variables can displayed in had. That's how I kept my HAD status pages working when transitioning from venlink to Nodelink. Paul

Hi Blake Welcome to the forums! The ISY Portal product supports IFTTT. And, IFTTT supports the Harmony hub. The amazon echo can be connected as well. It probably depends what kind of integration you're interested in... For instance, push an insteon keypad button, and have the hub turn on the tv, etc? Paul

To put one more option on the table, is io_guy's ISY Logger. I think it does exactly what you want and can ship the results to syslog if you'd like. You id the variables you want to track by checking a box next to their name. You do need a separate windows or Raspberry Pi type system to run it on your network Here is a sample of the csv output.. header row definition, followed by values: Time,Day,Month,Month_compare,Day_compare,V_FR_Fan_Cycle_Sequence,V_US_Fan_Cycle_Sequence 03/10/2016 00:12:40,9,3,3,9,29,52 03/10/2016 00:17:43,9,3,3,9,29,53 03/10/2016 00:32:41,9,3,3,9,30,53 03/10/2016 00:37:44,9,3,3,9,30,54 03/10/2016 00:52:41,9,3,3,9,31,54 03/10/2016 00:57:44,9,3,3,9,31,55 03/10/2016 00:59:58,10,3,3,10,31,55 03/10/2016 01:12:43,10,3,3,10,32,55 03/10/2016 01:17:46,10,3,3,10,32,56 03/10/2016 01:32:43,10,3,3,10,33,56 03/10/2016 01:37:48,10,3,3,10,33,57 03/10/2016 01:52:45,10,3,3,10,34,57 03/10/2016 01:57:48,10,3,3,10,34,58 03/10/2016 02:12:46,10,3,3,10,35,58 03/10/2016 02:17:49,10,3,3,10,35,59 03/10/2016 02:32:46,10,3,3,10,36,59 03/10/2016 02:37:50,10,3,3,10,36,60 03/10/2016 02:52:47,10,3,3,10,37,60 03/10/2016 02:57:51,10,3,3,10,37,61 ..... Paul

Thanks Michel!

There is now an alexa skill for the ventstar T5xxx through T7xxx series thermostats. These can aslo be controlled by the ISY using Nodelink/Venstar. ISY programs can be aware of changes and make them. http://venstar.com/smart/alexa/

GT I disabled notifications some time ago. Folks have been catching interesting opportunities from SH on amazon... recently got a plm delivered for $35, and just recently 2 motion sensors for about the same price. To your point, they have been becoming x10.com a little more in the marketing/spam dept, each year that goes buy. Paul

I'm going to have maintenance done to my sprinkler system and will likely be out of town when it happens. My project is to create a simple web page to turn my 14 sprinkler zones on and off, and serve access to it through the portal. I've shut all port redirection off on my router and don't want a solution that requires back tracking on that. I've kinda painted myself in the corner with options and the simplest, safest way to proceed Access / security: I think I should create a separate guest portal account with a separate key for accessing devices. This creates a separate key, so I don't give away the key that allows access to things I've created on my main account. I'll change the password for the guest account after the work is done....(?) Web page: Create a simple single page with a set of on/off links for each zone. Option 1: place that page on the ISY and provide a link through the portal (albeit ugly long link) to the contractor, via the guest account, to use from their phone. I've used this method for my sprinkler work in the past. Option 2: host the simple webpage on the internet somewhere at an address that's a little easier to remember. I could make an easier link for the contractor to access. Though that link wouldn't give away the guest key, the zone on/off links would and the page would remain "out there" on the internet. Any alternatives, other suggestions? I don't want to get in to figuring out apps for contractors phones, and would love to avoid giving them a tablet, etc to use. Web keeps the delivery model simpler, I believe. Paul

if you have on/off buttons controlling a light via a scene, you should be able to "press and hold" the on button for the light to brighten, and "press and hold" off to dim. It will be in finer increments than 25/50/75/100 edit.. If its a CFL load it will be hard to impossible to know if what I suggested works Paul

Great, glad its working. Thanks for reporting back Paul

I think your goal is to control these lights remotely, together, via a phone app? If yes, than that what needs to be addressed. It still involves a scene. But instead of of controlling the switches with the app, control the scene. Set up the scene, and control the scene remotely with your phone. I have the Agave android app, and I can add the Scene to Agave and control separate switches in unison, together. All related lights an switches turn on, turn off and dim in unison but controlling a single scene control in agave. Paul

Ok, I see what happened. When the lights get turned on it makes the program false and it terminates. The way to solve it is to have 2 programs: Once the second program is started, it will run all the way through Program 1 If Status 'Garage Lights' is Off And ( Control 'Garage Door - Left-Sensor' is On Or control 'Garage Door - Right-Sensor' is On ) Then Run program 'program2' (Then) Else - No Actions - (To add one, press 'Action') Program 2 If No Conditions Then Set 'Garage Lights' On Wait 2 minutes Set 'Garage Lights' Off Else - No Actions - (To add one, press 'Action')

Are you sure it didn't pop up at the root level of Main, e.g not in the folder? Paul

There's a fix on the way to "un-set" pump mode. For now, delete the ezflora, factory reset it and then add it back in. To factory reset an ezflora, unplug it for at least 5 seconds. Press the SET button while plugging back in. Continue holding SET button for 5 seconds and then release. Paul

Hi, sure Status is the actual state the device is in. Control responds to the device actually being turned on or off: If the garage lights are on, their status is on If the garage doors are activated, the control statement responds to that act. That's what I think you intend for your program, after either iolinc senses/activates, turn the lights on for 2 minutes and then back off. There's an opportunity to enhance this with a scene, let's see if the suggested changes work first though Paul

I'd switch from 'if status' to 'if control' for the iolincs only. Them being a status of "on" and the light being set off is starting the program over again. Also, put parens around the two 'if controls" If Status 'Garage Lights' is Off And ( Control 'Garage Door - Left-Sensor' is On Or control 'Garage Door - Right-Sensor' is On ) Then Set 'Garage Lights' On Wait 2 minutes Set 'Garage Lights' Off Else - No Actions - (To add one, press 'Action') Paul

Then it would be the program statements mwester listed, but instead of taking device action, set a State variable: $GarageDoorActivated = 1 when its in process of moving, and = 0 when its not. Have programs activated based on that variable change. I have a "layer" of variables like this that can be mixed and matched for various automated activities; sprinlers Paul

USe the ISY to create a new scene by using the 'New Scene' menu option at the bottom of the 'Link Management Menu' (next to 'File') Use the mouse to 'drag and drop' each switch into the new scene you created. When asked, make each switch a controller. This is the preferred way to do it, and not have to rewire. Paul

Agreed Teken, ADR is a 'problem focused' approach that heavily penalizes non-business customer for unpredictable demand peaks. I've learned to live with it under "interruptible" service we've had on our A/C for 25 years. The reality is that the demand peaks rarely happen that shut off our A/C... for very cheap power always on that meter. If you've seen UDI's proposal for RATES in a recent post, its turning the business model inside-out by not trying to manically solve it by measuring all of the details. Paul