asbril

Michel, everything works, so no concerns from me.

Version 3.0.41 Status: Connected Frontend Version: 3.0.41 ISY Version: 5.3.0 Uptime: 46 Minute(s) 20 Second(s) (c) 2022 UDI

I followed Michel's Sudo instructions and everything seems to work. IoP shows as 5.0.4 (not 5.0.4.2) in Administrative Console but 5.0.3 in XX.X.X:3000. It was mentioned that going forward one should no longer use Sudo for updates but do this within the Administrative Console (or in XX.X.X:3000 ?), but I don't see where / how. Furthermore where can I change the Polyglot's username / pw from admin/admin ?

yes

Something must not be right with my Notification nodeserver. In the Adm. Cons. Main tab my various Pushover nodes show, but each have a "0" only in message. When I create a program and select Notification Controller, I have the sub-options Nodeserver Online, REST Status and Notification. With Notification there is again only "0". Nowhere can I select one of the pushover nodes that are listed in the Main tab and same for priority etc. Right now I use my Pushover email address to send a notification to my phone, but no priority etc, I may have to re-install the nodeserver.

I have been trying to find out for several weeks, but so far nothing.

I moved the Notification nodeserver to IoP and it works. However I remember that I was previously able to set type of urgency to messages, such as normal, urgent, emergency (or similar). Regular messages work. Now I don't see anywhere where to set the priority.

nope

Yes I waited more than 15 mins

I did the 6 * reset and everything seems to work and no more flashing.

I think that upgrade went through. I have not yet done the 6 * reset and Polisy is still flashing.

Thanks !!!!! In the Administrative Console, the ISY shows as 5.4.0. In Putty, it says that everything is up to date. I assume that the pinhole in the front of Polisy is the reset button, and I should press it with a paperclip 6 times ?

I also have the flashing light. everything seems to work as before (though PG3 still shows 5.3.0), except for Weatherbit; the controller shows all data in Celcius but at zero. The other days show data in Fahrenheit and apparently with correct data, but with wrong day. Node 0 shows as Sunday and Node 1 shows as Monday...... while of course it is now Tuesday. I don't use the nodeserver in any program, so it is not a big issue.

I did that as well

I did in Putty : sudo pkg update sudo pkg upgrade sudo service pg3 restart No error message but Polisy still shows : Version 3.0.41 Status: Connected Frontend Version: 3.0.41 ISY Version: 5.3.0 Uptime: 13 Minute(s) 1 Second(s) (c) 2022 UDI Running on Polisy Documentation

I always wonder how Michel finds the time for these individual sessions. I have had the benefit of several of these and it shows extraordinary commitment.

BTW a lesson learned. This morning I performed a Synch All and some 5 old Zwave devices showed up that I had removed some time ago, either because I forgot to exclude or because the switches just failed and could not be excluded. They remained in my network, possibly creating interference. I now removed these as remove failed node, something I should have done long ago.

I know nothing about Ring......other than it exists

No Update Neighbors is the same as what used to be Heal Network in previous version of ISY, excelt that it is now individual for each Zwave device. Synchronize is synchronizing the Administratve Console with the Zwave dongle.

I would definitely use that method. In theory, with Zwave 500 and 700, the mesh network automatically selects the best route for each device, but I suggest to do 'Update Neighbors' for newly added devices. That should help when adding devices further away from the dongle. Sometimes, however, the inclusion does not work because tne new device is too far from the dongle. I built a "portable" switchbox with a plug and I temporarily connect the new switch to that box close to the dongle for inclusion. Then I move the switch to its intended location. Over time the mesh network will (should) automatically select the best route for all devices.

I now have been using UD Mobile for several days on two of my Windows 11 computers and I am very impressed. The Bluestack solution works perfectly and I even found a way to add UD Mobile to my taskbar. UD Mobile is very flexible. I added folders and scenes to the UD Mobile's favorites tab and I can do everything (*), and more than what I used to do on Home Asssitant (as a front for ISY). I have devices on both ISY and I-on-P, and they can all be used in UD Mobile. I wil give it a bit more time, but I don't think that I will need Home Assistant anymore. I also added the same UD Mobile solution to an older Windows 10 computer, but there the performance is not as good. As an aside, after moving some of my Zwave devices, programs and nodeservers, from ISY to I-on-P, I have noticed a serious improvement of my setup. It is faster and the Administrative Console opens properly 99% of the time, compared to before when often I had to try 4 or 5 times before the AC would open. My only small issue now is that I have a Homeseer dimmer switch in our master bedroom that I set up so that the sentinels show green or red to let me know if lights are on in the different rooms. Because two rooms are now on I-on-P, these two rooms no longer show. Something to work on. In short, bravo to UD and Javi. (*) I work a lot on my computers and prefer to use the pc to turn on lights, music programs etc rather than using my phone. I have both Alexa and Google Home, but voice commands are not always accurate (my European accent ???? ?).

I have done some reading on this and found out that Zwave Associations do indeed exist, but I am not sure whether the issue is ISY or the actual devices, depending on the manufacturers. ISY is Zwave certified (5.3 or 5.3.3 ?) and therefore I have some doubt that it would be an ISY issue.

I don't know if this is of any help, but I use the Harmony Hub nodeserver to switch the TV ON as part of a wake-up program. It selects the channel and the volume. Very useful.

@Javi This is absolutely amazing ! I installed it on one of my pc's and it does everything I was looking for. The initial setup took some 15 minutes and I actually used the Google App Store instead of the Amazon Store, but same results. I added Bluestack to my windows taskbar, and then I need to wait a minute to get to UD Mobile. Maybe one day I can get directly to UD Mobile, but right now I am a happy camper. Thanks Javi for the amazing App and your help. BTW This morning Michel , once again, helped out of a major disaster with my setup. My whole Zwave network had crashed and nothing I could think of worked. Michel identified that one of my devices was creating havoc and by power cycling a switch that seemed to be the culprit, my whole system came back..... and Michel relieved me of my frustration. I am more and more getting on @lilyoyo1's side that Zwave has serious issues, but I have invested a lot in my setup. However once there is a new Lutron nodeserver, tested and working, I will gradually move to RA3.

Nice Javi, I will test that tomorrow