belanger Posted October 4, 2016 Posted October 4, 2016 I purchased two of those GoControl GB00Z Smart Glass Break Detector, I added to ISY under v5.0.5. In the beginning I was only seeing the battery level at 0%. I had to go out and back 1h30 later, I see a battery level of 0% and a Status of 0% as well. Perhaps within next 24 hours the battery level will get populated. I'm not sure what that Status = 0% mean and there's no "alarm on/off" status at all. Z-Wave glass break sensors are rare, can we manage to add this one? Tue 10/04/2016 16:45:04 : [ZW-SHOW ] ---------------------------------------------- Tue 10/04/2016 16:45:04 : [ZW-SHOW ] ZW016_1 uid=16 type=4.161.2 mid=335 tid=18242 pid=12336 model=0 Tue 10/04/2016 16:45:04 : [ZW-SHOW ] - x20 V1 BASIC Tue 10/04/2016 16:45:04 : [ZW-SHOW ] - x9C V1 SENSOR_ALARM Tue 10/04/2016 16:45:04 : [ZW-SHOW ] - x80 V1 BATTERY Tue 10/04/2016 16:45:04 : [ZW-SHOW ] - x82 V1 HAIL Tue 10/04/2016 16:45:04 : [ZW-SHOW ] - x84 V2 WAKE_UP Tue 10/04/2016 16:45:04 : [ZW-SHOW ] - x87 V0 INDICATOR Tue 10/04/2016 16:45:04 : [ZW-SHOW ] - x85 V0 ASSOCIATION Tue 10/04/2016 16:45:04 : [ZW-SHOW ] - x72 V0 MANUFACTURER_SPECIFIC Tue 10/04/2016 16:45:04 : [ZW-SHOW ] - x86 V0 VERSION Tue 10/04/2016 16:45:04 : [ZW-SHOW ] - x5A V0 DEVICE_RESET_LOCALLY Tue 10/04/2016 16:45:04 : [ZW-SHOW ] Tue 10/04/2016 16:45:04 : [ZW-SHOW ] Node 16 - ZW 016 Alarm has the following neighbors Tue 10/04/2016 16:45:04 : [ZW-SHOW ] - - Node 1 - [This ISY] Tue 10/04/2016 16:45:04 : [ZW-SHOW ] - Repeater - Node 3 - Repeater Tue 10/04/2016 16:45:04 : [ZW-SHOW ] - Repeater - Node 4 - ZW 004 Dimmer Switch Tue 10/04/2016 16:45:04 : [ZW-SHOW ] - Repeater - Node 5 - ZW 005 Dimmer Switch Tue 10/04/2016 16:45:04 : [ZW-SHOW ] - Repeater - Node 6 - ZW 006 Dimmer Switch Tue 10/04/2016 16:45:04 : [ZW-SHOW ] - Repeater - Node 7 - ZW 007 On-Off Power Switch Tue 10/04/2016 16:45:04 : [ZW-SHOW ] - Repeater - Node 8 - ZW 008 On-Off Power Switch Tue 10/04/2016 16:45:04 : [ZW-SHOW ] - Repeater - Node 9 - ZW 009 Siren Tue 10/04/2016 16:45:04 : [ZW-SHOW ] Tue 10/04/2016 16:45:19 : [ZW-SHOW ] Node 16 - ZW 016 Alarm cannot retrieve association groups Tue 10/04/2016 16:45:19 : [ZW-SHOW ] Tue 10/04/2016 16:45:19 : [ZW-SHOW ] ---------------------------------------------- Tue 10/04/2016 16:45:23 : [ZWAVE-WAKEUP 16] Awake with no pending work, putting back to sleep ZW016_1
belanger Posted October 5, 2016 Author Posted October 5, 2016 If I try to Query that device, I get the following pop-up : Could not open config file to read [/CONF/0038.CZW] Subscriber didn't reply to event: 1 [39]
Chris Jahn Posted October 5, 2016 Posted October 5, 2016 Hi belanger, We do support glass break sensors, but I not sure whats going on with yours. My guess is the query failed because the device was not awake. I don't know why its not reporting its status or battery level correctly though. We'll have to look at why you are seeing a percentage for the status.
belanger Posted October 5, 2016 Author Posted October 5, 2016 The battery % level populated later w/ a value of 2 , confirmed via the z-wave msg shown in the logs. The only other available value is still "status 0%", aka there's still no "on / off" alarm status. I noticed at times variable showing up only after the device sent a message. For example, the "Alarm on/off" might show up in the UI once the alarm trips. If this normal behaviour? I was always under the impression that all values would show up from the moment the device joins. Without that variable, how can somehow program in advance a condition using any variables exposed by the device? Let me know if you need anything else from me to troubleshot the device issue. Pierre
Chris Jahn Posted October 6, 2016 Posted October 6, 2016 When a device joins the network we query it, but in some cases it doesn't respond. When that happens, we don't have a status for us to report for that device. I have to check for 'Alarm' though, I think it doesn't even show the box in the GUI if it doesn't have a value. Can you run the following from a browser using the ISY Address of your glass break sensor node (its something like 'ZW016_xxxxxx'). http:///rest/zwave/node//def/get
belanger Posted October 6, 2016 Author Posted October 6, 2016 There you go : <nodeDefs> <nodedef id="UZW0026" nls="148"> <sts> <st id="ST" editor="_51_0"/> <st id="BATLVL" editor="_51_0_R_0_100"/> <st id="ERR" editor="ZW_ERR" hide="T"/> </sts> <cmds> <sends/> <accepts> <cmd id="QUERY"/> <cmd id="WAKEOPTS"> <p id="INTERVAL" editor="ZW_WAKE_INTERVAL"/> </cmd> </accepts> </cmds> <links> <ctl/> <rsp> <link linkdef="ASSOC"/> <link linkdef="ASSOC_CMD"/> </rsp> </links> </nodedef> </nodeDefs>
Recommended Posts
Archived
This topic is now archived and is closed to further replies.