Dave H Posted October 25, 2021 Posted October 25, 2021 Neophyte. First use of new 994. Half dozen controllers, a dozen lights. Trying to communicate with an outdoor on/off unit, consistently getting this error: "The following devices could not be added: 22.80.75 (2634-222) On/Off Outdoor Module V.00 device is an old PLM, do Restore modem and try again." I've done the restore modem, and tried manually and automatically to find this device. When I do it manually I get the above error, when I try to do it automatically, the device is not found even though the controller it is linked to is found. controller and device work as programmed. help. -dave :
larryllix Posted October 25, 2021 Posted October 25, 2021 (edited) 11 minutes ago, Dave H said: Neophyte. First use of new 994. Half dozen controllers, a dozen lights. Trying to communicate with an outdoor on/off unit, consistently getting this error: "The following devices could not be added: 22.80.75 (2634-222) On/Off Outdoor Module V.00 device is an old PLM, do Restore modem and try again." I've done the restore modem, and tried manually and automatically to find this device. When I do it manually I get the above error, when I try to do it automatically, the device is not found even though the controller it is linked to is found. controller and device work as programmed. help. -dave : Is the device on the same powerline phase (120V leg) as the PLM is? Do you have any bridging between your powerline phases? Have you factory reset the device before attempting to link it with your PLM? What ISY firmware version are you running and what UI are you running? Edited October 25, 2021 by larryllix
MrBill Posted October 25, 2021 Posted October 25, 2021 try plugging the outdoor module in on the same circuit as the ISY/PLM Also Note that device codes on the stickers can be hard to read... 22.80.75 the 80 could be 8D, B0, BD 1
Techman Posted October 25, 2021 Posted October 25, 2021 1 hour ago, Dave H said: Neophyte. First use of new 994. Half dozen controllers, a dozen lights. Trying to communicate with an outdoor on/off unit, consistently getting this error: "The following devices could not be added: 22.80.75 (2634-222) On/Off Outdoor Module V.00 device is an old PLM, do Restore modem and try again." I've done the restore modem, and tried manually and automatically to find this device. When I do it manually I get the above error, when I try to do it automatically, the device is not found even though the controller it is linked to is found. controller and device work as programmed. help. -dave : What is your ISY and UI firmware versions. They must be the same for everything to work properly.
Dave H Posted October 27, 2021 Author Posted October 27, 2021 Thanks all-- 1. firmware and UI version 4.9 2. not sure about phase, but I have plugged a repeater into the same branch circuit and I see that communications are very reliable. 3. Did a factory reset of outdoor module and another PLM restore Same error message! -dave
Techman Posted October 27, 2021 Posted October 27, 2021 (edited) Perform the "4 tap test" to confirm that both legs of your powerline are bridged. This works with the range extenders and most of the newer modules Instructions are attached. 4 Tap test.pdf Edited October 27, 2021 by Techman
Brian H Posted October 27, 2021 Posted October 27, 2021 If the 4 test does not work. There are a few modules that you have to look at the manual for it. Then perform the Beacon Test. Through a series of set button pushes and LED color and flash patterns. To start it. It is in a flow chart in the modules manual.
lilyoyo1 Posted October 28, 2021 Posted October 28, 2021 Bring module close to ISU/PLM. Choose start linking>press set button on device until you hear the chirp
Dave H Posted October 28, 2021 Author Posted October 28, 2021 4 tap test plus lilyyoyo1's suggestion carry the day. Thanks everyone! -dave
Recommended Posts