Jim P Posted February 25, 2022 Posted February 25, 2022 I Can't seem to add any Z-wave devices to ISY on Polisy .. ( Yellow Cap Z-Wave Dongle ) (Z-Wave device is 5 feet from dongle) Fri 02/25/2022 07:19:19 AM : [ZWAVE-TX-NR ] [0105004AC1F081] REQ ZW_ADD_NODE_TO_NETWORK Fri 02/25/2022 07:19:19 AM : Listening for Z-Wave devices to add to the network Fri 02/25/2022 07:19:25 AM : [ZWAVE-TX-NR ] [0105004A85F1C4] REQ ZW_ADD_NODE_TO_NETWORK Fri 02/25/2022 07:19:25 AM : Adding Z-Wave devices stopped Fri 02/25/2022 07:19:25 AM : [ZWAVE-TX ] [01030020DC] REQ MEMORY_GET_ID Fri 02/25/2022 07:19:25 AM : [ZWAVE-TX ] [01030056AA] REQ ZW_GET_SUC_NODE_ID Fri 02/25/2022 07:19:25 AM : [ZWAVE-TX ] [01030002FE] REQ SERIAL_API_GET_INIT_DATA Fri 02/25/2022 07:19:26 AM : [ZWAVE-TX ] [01030005F9] REQ ZW_GET_CONTROLLER_CAPABILITIES Fri 02/25/2022 07:19:26 AM : [ZWAVE-TX-NR ] [0105004A850035] REQ ZW_ADD_NODE_TO_NETWORK Fri 02/25/2022 07:19:39 AM : [ Time] 07:19:41 0(0)
lilyoyo1 Posted February 25, 2022 Posted February 25, 2022 What devices are you trying to add and what process are you using
Jim P Posted February 25, 2022 Author Posted February 25, 2022 ZW39 Eva Logik Z-Wave Smart Plug (Dimmer) Menu Z-Wave Add a Z-Wave Device BTW.. I have not been able to add any Z-wave devices .
lilyoyo1 Posted February 25, 2022 Posted February 25, 2022 Did you try to remove first? How many button presses on the devices?
Jim P Posted February 25, 2022 Author Posted February 25, 2022 If I try to remove Z-Wave devices I get similar results.. Listening for Z-Wave devices and no response. 3 quick presses and buton begins to blink rapidly.
Jim P Posted February 25, 2022 Author Posted February 25, 2022 I added this module.. I tried adding a Z-Wave light switch with no results.. I tried removing the first module and it removed. I Added the first module again. I tried a different modue with no results. The plug in modules are added very close to Z-Wave dongle.. I move the one that is added about 15 feet away and it responds to the ISY commands and I can remove it and readd it from it's normal location.. Perhaps there is something still in working stage.. although I have not read about anyone else having these issues.
Techman Posted February 25, 2022 Posted February 25, 2022 (edited) Is the Zwave box checked, and saved, in the Polisy configuration window? If so, the then do a reboot on the Polisy by pushing the reset button ONCE in the right front of the polisy using a paper clip, Edited February 25, 2022 by Techman
Jim P Posted February 25, 2022 Author Posted February 25, 2022 Did all that.. I have not set a ZW device back to factory defaults yet, but I want to wait untill I have this issue fixed before I do that to my installed light switches...
lilyoyo1 Posted February 25, 2022 Posted February 25, 2022 2 hours ago, Jim P said: Did all that.. I have not set a ZW device back to factory defaults yet, but I want to wait untill I have this issue fixed before I do that to my installed light switches... I'd return your zwave board and get a new one.
Jim P Posted February 26, 2022 Author Posted February 26, 2022 How do you exclude a Zwave device if it has never been added to your IoP ? Is exclude the same as remove then readd ?
lilyoyo1 Posted February 26, 2022 Posted February 26, 2022 27 minutes ago, Jim P said: How do you exclude a Zwave device if it has never been added to your IoP ? Is exclude the same as remove then readd ? Yes
Jim P Posted February 26, 2022 Author Posted February 26, 2022 OK.. I am brain dead !!! Funny but here is what happened... I have always only had a single ISY ... Soo... It never occurred to me to remove my Zwave devices from my 994i before attempting to add them to my IoP ... This AM I removed one from the 994i and did not have any issues adding it to my IoP.. So I am going forward with removing them all from my 994i and adding them to my IoP. I am not expecting to see any more issues with this. Thank you all and sorry to have wasted your time. 1
Recommended Posts