Panda88

Can you try to erase the REFRESH_TOKEN key save (not just the value but the key)- and then restart? It seems to old token is somehow stuck in polyglots database

looks like something went wrong during installation - Can you try to remove it (fully) and install again - it is like it is not registered correctly in the node store

try to start again but get the log from upper right corner - it looks like the node server does not start at all

ny chance you can provide a full log - the error happens earlier - but it does look like the token did not refresh corectly Tesla does change their API once in a while and as there is no official API it takes a little while to get it updated It can also happen they log you out if you poll too often so try to log in at website to see if that works I am travelling now so there will be some delay on support

t looks like you found the place to put it (at the bottom - REFRESH_TOKEN) - Is the one shown one you entered - if not clear the filed and replace it with your token - make sure that there is not a blank space at the end of the token - I had that issue in the past. If it does not work, can you post a log file there - I need to know what it is wrong. Also it the version looks wrong - but it could be related to the node not starting

I believe a full power cycle should do it -unless you had a very early version I think you may have the latest version already

When you reboot it is designed to remove existing nodes and then recreate them - you often need to refresh the browser to the the node server to show all - it is a known polyglot UI issue Have you updated polyglot to latest version? There have been some node handling changes recently I do not see the behavior you describe - maybe you can enable debug in the log and send me a long log - Maybe I can figure out what is happening

Really strange - There is no communication from the Yolink cloud - Using MQTT the sensors should report by them selves - I am only querying once an hour - nothing coming from the cloud - maybe try to generate new credentials For the UDI mobile issue - did you try to reboot the PoI ? The text files are only read at reboot - updating the server is not enough - little strange but it seems to be the case

Are you running a different application with the same credentials (like HA or similar) - It seems only one one application can use the same credentials at a time . I am not 100% sure, but I have seen the same when using 2 different ISYs running the same code. I see the code initializing but then nothing happens - it times out and reacquires the token. I think another application has the control I did find an error on the door sensor that I fixed - I did not update version yet but uploaded the fix I am travelling and cannot test the code change.

Congrats on the car, I think this should work - you can specify max charge current - but you need to make sure it works correctly - I have not been able to verify it You have to be a little careful as there is (I believe) a delay from the tesla API - I htink commands are ok but getting data back may have some delay

Can you provide a log file from the node serer?. Aldo try to restart the node server after update. I think there were some cloud issues yesterday

Try 0.4.2 - I no longer remove nodes - There may be an issue with multi devices - as I cannot create the sub nodes as there is no information on them - I'll look to keep the state but it is a more complex change

I agree - but they are supposedly working on a local mode as well

I'll be looking at it today - hopefully not too complex. Also, Maybe I should change the error to warning - program should keep running and as soon as node is back on-line it should pick up again (assuming it was there when the Node server startted)

Yes - this is expected

There is no local API yet - they are working on something but not released yet - will likely need a new version of HUB to do it

yes - it detect the motion sensor as off line when installing and then it removes it - It is probably too aggressive - I should just keep it an let it show off-line - I have to assume that devices registered are supposed to exits I'll look at making that change later

I need the log from the node server - go to polisy and go to node server and then download log The on-line checks if the cloud api has a connection/communication with the motion sensor It is possible I made a mistake but mine show up???

If a device is not on line when restarted it is removed - Maybe that is too aggressive - let me know. Send me an log and I can take a look

I forgot to change the version number in the code - did a 0.4.1 - try that

0 means closed - there is an issue that I have been struggling to find on the udiMobile - is somehow does not pick up the number to text conversion

Is this a yolink device ? The door state is an input (opened or closed) - to control the door need to use the finger - issue a toggle to the finger

the changes are in the IF portion

Changes should be int he programming are - if you choose control in the conditional statement the nodes that can be controlled should show up now - e.g. a motion sensor should show up allowing control when there is motion - vs. a state change as before - In my mind there is little difference as the node server is MQTT based so the state change happens at the same time but it does not hurt to support both I guess . Or are you saying you do not see the nodes under control?

Dropped 0.4.0 Added support for Control (and state) in relevant nodes Let me know it works