Techman

also when using HAMWeather you'll need to search by city name as it doesn't recognize zip codes. It's best to upgrade to the current ISY firmware as it addressed some climate bugs.

You'll need to upgrade your firmware to 4.2.5 as HAMWeather is better supported beginning with that release (see the release notes for bug fixes).

Thank you. I did the restore and went from a 950 link count down to 306. It's hard to believe that I had so many dead links in the PLM, that's quite a significant memory recovery. The restore screen went up to about 13% then closed. Hopefully everything got restored.

You might be getting a voltage drop when the fan starts up due to a poor electrical connection. . How many watts are your lights drawing? What type of bulbs are you using, CFL or incandescent? When the lights are on and you turn the fan on does the fan speed seem to initially lag?

If I do a restore to an existing PLM do I still need to put all the battery operated devices in link mode as the restore PLM pop up window requires? I have 9 of them. What will be the outcome if I don't? Can I write to them after the restore by individually triggering them and setting the 994 pro to auto write?

K5MAP When you refer to the 0-15 I assume you're referring to the LED brightness levels on the KPL buttons as that's the only 0-15 option for the KPL. If you want each of your buttons to control a different scene then you need to place that button into the scene as a controller along with the device(s) you want the scene to control. You don't need to change the action of the buttons, they should be in the toggle mode assuming that you want to toggle your scenes on and off. Hope this helps Techman

I'm close to running out of link space on my PLM. Will a modem restore free up PLM memory by deleting unused links etc.?

MustangChris04 The contact should be CLOSED and the green status LED on the I/OLinc should be ON when the garage door is open, the LED should be off when the door is closed. If that's the case then you're properly wired. Make sure that you don't have trigger reverse enabled on the I/OLinc

see following post

MustangChris04 The bulb is not connected to a switch or dimmer, it is being controlled directly by the ISY Brian H I have numerous LED bulbs connected to various Insteon controllers and none of them flicker when dimmed except the Insteon bulb. Smarthome said when the bulb is connected to a Insteon Hub it didn't flicker so it's possible I have a defective one.

I just installed one of the 9 watt bulbs and noticed that when I dim or brighten it flickers during the process but is steady once it reaches the intended brightness. I spoke to Smarthome who said that when using the Insteon Hub they didn't experience any flicker. I'm wondering if I have a bad bulb or if the ISY algorithm is causing the flicker.

Catch up schedules is NOT checked Query at restart IS checked

I just added the climate module and about two minutes after the ISY rebooted everyone of my devices turned on. The ISY didn't reflect the on status of the devices. Is this a coincidence and/or is my PLM on the way out? This is the first time I've experienced this.

Here's the ISY994 LED troubleshooting info. Hope this helps

I originally had it that way and was getting SMTP errors from one of the ISP's so I divided them into two groups. I'll try combining them once again to see what happens.

I reversed them a while ago and the issue always seemed to be with email that was in second position. Do you have any idea how the outgoing emails are processed? I currently have email 1 in group id 1 and email 2 in group id 2. At one point I had them under the same group ID and still had an issue.

The following program is run if a door event is triggered. Email 1 is always received, however Email 2 is intermittent, sometimes it shows up sometimes it doesn't. The emails are sent to two different ISP's. There is nothing in the error log showing any mail server issues. How does the ISY process multiple emails sent at the same time? Do I need a longer wait time between notifications? Currently running 4.2.3, I also had this issue with the previous release If -No conditions Then Send Notification to 'Email 1' content 'Door Open' Wait 2 seconds Send Notification to 'Email 2' content 'Door Open' Else No action

I'm using 8 button KPL dimmers v.41 and .43 and have had no issues with the CREE Led bulbs. Not sure if there were issues with the older KPLs. The CFL's can be somewhat problematic. I've also had issues with the Philips bulbs and no longer use them. It might be worth it to pick up one of the later KPL's on sale and see if that solves your problems, if it doesn't you'll probably need to try a different bulb.

LeeG, once again many thanks, it's now working.

Is it possible to adjust the load (button A) local on level on a 6 button KPL dimmer based on the time of day using a scene or a program? The KPL is showing as a 5 button KPL in the ISY, not sure why I was able to adjust the on level on a SwitchLinc dimmer but it doesn't seem to work on the KPL. Thank you.

Hello Intellihome, After trying numerous led bulbs I found the CREE A19 led bulbs, which are sold at Home Depot stores and online, to work very well with the Insteon products. I'm able to dim them all the way down and up without any flicker or noise. They're currently available in 40w, 60w, and 100w equivalent. They come in both 2700k (soft white) and 5000k (bright white) color temperatures. The 2700k is most comparable to the color temperature of an incandescent bulb.

I'm not familiar with the Honeywell panel but if you have a dry contact N/O and a Common lead coming from the panel and if the N/O contact closes when the panel is armed then all you need to do is hook up those two leads to the Sensor and Ground contacts on the I/O Linc.

There's a documented issue with 4.2.2 and/or Java that causes the admin console to freeze up under certain conditions. This may be what's causing your issues. UDI said they will have a fix included in the next beta release.

I would like to change the state of an On/Off module each time an I/O Linc receives a momentary signal on the sensor input. Not sure the best way to proceed. UPDATE - think I figured it out. I set a state variable to change each time the sensor input receives a signal.

I've been seeing several 10011 messages in my error log lately. What triggers this error? 10011 - RSA REIMPORT KEYS FAILED