Techman

Most of the smartmeters use a Zigbee radio. You should check with your utility provider to verify its radio and to see if they will provision your meter to allow you to read its radio. You would then need to purchase the Zigbee module from UDI which will add Zigbee compatibility to your existing ISY.

jbferg Can you post a screenshot of the KPL scenes. Are the KPL buttons listed as a controller in all the scenes? Have you tried a factory reset on the KPL?

Open your ISY error log and take a look for possible SMTP or other errors around the time you had the email failures. Also try increasing your email time out value in the ISY configuration settings. Who are you using for your mail server?

Paulbates The extension cord would be for testing purposes only, just to try to isolate your issue by moving the PLM away from equipment that may be interfering with your powerline signal. Use a cord that has a ground.(3 prongs).

Depending on what else you have plugged into the same circuit as the PLM, it's possible that something (in your rack?) is interfering with the PLM powerline signal. A UPS or computer close to the PLM will have an adverse effect on your PLM signal. Try using an extension cord and plug the PLM into a different circuit if possible. Keep in mind that the I/OLinc is a powerline only device. If that resolves your issue then you need to isolate the device that's interfering with the PLM with a FilterLinc.

Tellijcl Take a look at your error log about the time you didn't receive an intended email. That will help you narrow down the problem. Also try increasing the timeout in your email configuration. If you're sending out several emails at the same time try putting a few seconds wait in between the notifications.

It's very simple If Module Climate (parameter) is xx Then send notification Else do nothing

Not sure what else to suggest. If no one else has a solution then you should submit a ticket to UDI and they will get you squared away.

Are there any devices showing in the folders below "My Lighting? If so, try moving them out of the folders

I don't think there's an Insteon module that will work with your setup. The chime most likely doesn't draw enough current to trigger a Insteon Synchrolinc 2423A5, but you may want to look into it.

It was mentioned in the 4.2.5 firmware release. http://forum.universal-devices.com/topic/13501-release-425-rc-is-now-available/

Input a city name rather than a zipcode. You'll also need to have the latest ISY firmware.

Michel When I query the "CO2 Detected" node I don't get a response, same with the "Clear" node, and the smoke detected node. All the other smoke bridge nodes respond to the query. The "current state" for these three nodes is blank, the rest of the nodes all show as off. Is this correct?

Seems it could best be used to send out an email indicating that the ISY is back up after a power failure

This is what I get if I type in Riverside (see attached). In the ISY Help > About, Make sure that both your firmware and UI are both 4.2.8. Are you running the latest Java version 1.7 update 67 (the update may vary depending on your browser)

What displays when you type a city name into the find box? If an acceptable station shows then click on save. I'm using Internet Explorer, not sure if there's a Firefox issue.

If you click on the scene name does it show an on level for the kitchen table light to be something other than 0?

If you're using the UDI default mail server it was down for a short while

there's not a separate log for the thermostat. if you look at your ISY log you'll find entries for the thermostat's temperature. you could also have the ISY email you the current temperature every xx minutes, etc. that could be done with a simple program. Update - I just saw your second post. The specs show the operating range for the thermostat as 39 to 104 degrees, so it probably won't work for the freezer

When I entered Bokeelia in the find box it found a station (see attached). Hope you get it resolved.

Easytim some of us have been having intermittent problems with the climate module. when I entered fort myers I got the following results (see attached) If you're still having issues you should submit a support ticket to UDI.

Click on "Find" then enter just a city name in the find box, no zip code or state. Once you have an acceptable station click on it then click "Save" Let me know it that works for you.

No need to contact HW. You'll need to update your ISY firmware to 4.2.8. The latest version of the firmware supports HamWeather.

I've also noticed that some feeds are intermittent and/or there one day and not the next. Try using the closest airport as a location just to see if you're getting updates. The airports are usually the most reliable stations and have the most data. Station KORD is O'Hare Airport.

Take a look at your error log to see if there are any errors related to HamWeather.