dbuss

ISY portal information: http://wiki.universal-devices.com/index.php?title=Main_Page#ISY_Portal_Installation_Instructions Agave information: https://www.agaveha.com/

I use the skill with my Harmony remote and it works quite well. It will turn on and off any activity I have programmed in my Harmony. It will adjust volume up and down. It will mute and unmute. It will go to the channel on the TV I ask it to go to. It's pretty neat.

Seems to be working now. Sent from my XT1650 using Tapatalk

Same problem here.

The new Amazon Show is supposed to work with Ring. Sent from my XT1650 using Tapatalk

But, I have to buy it, to find out what it's all about......hmmmmmmmmm.....seems I heard something like that before. So, I ordered two.

I had the same issue Here's the solution. http://forum.universal-devices.com/topic/19368-unable-to-backup-isy/

Elk does have wireless sensors and you can have an area setup for your residence and another area for your office. Sent from my XT1650 using Tapatalk

Thanks TrojanHorse and Stu. Sent from my XT1650 using Tapatalk

I have a program to turn on some indoor lights if motion is sensed by my outdoor motion sensors. The program seems to run all the time rather than just 11:00 PM to Sunrise. What have I done incorrectly? Thanks!! Indoor Security Lights - [iD 0051][Parent 0001] If From 11:00:00PM To Sunrise (next day) And Status '1 car Garage MS-Sensor' is On Or Status '2 Car Garage MS-Sensor' is On Or Status 'Lower Deck MS-Sensor' is On Then Run Program 'Indoor Security Lights 2' (Then Path) Else - No Actions - (To add one, press 'Action') Here's the Indoor Security Lights 2 program. Indoor Security Lights 2 - [iD 004E][Parent 0001] If - No Conditions - (To add one, press 'Schedule' or 'Condition') Then Set 'Living Room Floor Lamp ZW' On In Scene 'Kitchen Lights' Set 'Kichen Light Switch 1' 100% (On Level) Set 'Living Room Table Lamp' On Wait 10 minutes Set 'Living Room Table Lamp' Off Set 'Living Room Floor Lamp ZW' Off In Scene 'Kitchen Lights' Set 'Kichen Light Switch 1' 0% (On Level) Else - No Actions - (To add one, press 'Action')

I have two Echos, a Dot and four Fire TVs associated with the same ISY. Stusviews has multiple devices also and has them setup very nicely.

Echo does well in a room with noise as long as you have the Echo placed closer to you than source of the noise. I experimented with one of my Echos and placed it right under a wall mounted TV. When speaking about eight feet away it had some problems in that location. I moved the Echo about four feet from me and six feet from the TV and it works great.

http://www.businessinsider.com/otto-self-driving-truck-uber-purchased

I have not been able to avoid the "found several devices with the sane name" with this. I have not experimented much with different names either.

I control each fan speed and off with scenes. The KPL buttons update with each change made with Alexa.

I've not experimented a lot with the FanLinc. However, I'm able to tell Alexa to turn the fan on to wanted fan speed by saying turn on the fan name and then the desired speed. The only way I seem to be able to turn off the fan is to tell Aleax to turn on fan name off.

That fixed it. Thank you Michel.

I am unable to backup my ISY. During the backup process i get this error "Could Not Retrieve File /Conf/76.PRP" Firmware and UI are both 4.5.1 Thank you.

Log.pdf

Here's the log.

Main Level Bathroom Ceiling L Fade Start 1 Sat 2016/07/09 11:29:15 PM Web Log Scene:Smoke Alarm Fade Start 1 Sat 2016/07/09 11:29:30 PM Web Log Scene:Smoke Alarm Fade Stop Sat 2016/07/09 11:29:32 PM Web Log

Stu, The Zwave devices are controlled with a program. My error for not adding that bit of important.information.

I have a scene that is activated by a smoke bridge when a smoke alarm or CO2 alarm is activated. Last night the scene was activated. However it was activated with a fade start. There is no fade start in the scene. The scene has the lights turning on at 100%. Also, the Zwave devices in the scene were not activated. Just before the smoke bridge scene was activated the main level bathroom ceiling light was fade started. This light is controlled by a scene that is activated by a motion sensor. At this time of day the scene has the light turning at 35%. There is no record of the motion sensor being activated. We were not home at the time it happened, so I can't tell you if a smoke alarm went off. It appears it was started and stopped via the web. Could the fade starts and stops have been accidentally started when using Mobilinc? Thanks!!

I have a 2gig CT100 Z-Wave Thermostat and a RCS TZ45 Thermostat. The 2gig is being used where there was not a common 'C" wire. Both thermostats have been installed for about a year and have worked flawlessly. The battery has not needed replacement in the 2gig thermostat yet.

Thank you.